- DL manuals
- Z-Wave
- Computer Hardware
- IOMOD10F
- Hardware user manual
Z-Wave IOMOD10F Hardware user manual
Summary of IOMOD10F
Page 1
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 i iomod10f xtal calibration module v1.1 and carrier board for the sigma z-wave 500 series of ics and modules hardware user manual.
Page 2
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 ii.
Page 3: Contents
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 iii contents contents ................................................................................................................................ Iii copyright information ............................
Page 4
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 iv 1.2 iomod10f - spi interface via 10-way idc connector ................................................ 31 1.3 iomod10f - uart interface via separate wired signal connections ............................
Page 5: Copyright Information
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 v copyright information information in this document is subject to change without notice and does not represent a commitment on the part of the manufacturer. The software described in this document is f...
Page 6
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 vi equinox warranty information this product is guaranteed by equinox technologies uk limited for a period of 24 months (2 years) after the date of purchase against defects due to faulty workmanship or ...
Page 7: Disclaimer
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 vii disclaimer whilst every effort has been made to ensure that programming algorithms are correct at the time of their release, it is always possible that programming problems may be encountered, espec...
Page 8: Compliance
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 viii electromagnetic compatibility (emc) compliance the 'iomod10 - z-wave calibration module' is a ce approved product but only when used in conjunction with an equinox ‘ispnano programming module’. It ...
Page 9: Technical Support
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 ix technical support it is often the case that users experience problems when installing or using a product for the first time. If you have a technical support problem, please consult the following list...
Page 10
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 x.
Page 11: (Fixed Frequency Version)
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 1 1.0 iomod10f - z-wave calibration module (fixed frequency version) 1.0 overview the ‘iomod10f’ module has been specially designed to support 'xtal calibration' of the z-wave 500 series ics and modules...
Page 12
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 2 1.2 principle of operation of the iomod10f module the ‘iomod10f - calibration module’ is simply a hardware block which generates a very accurate / stable 'calibration frequency' for use with the 'z-wa...
Page 13
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 3 1.3 oxco - frequency generator block the 'oxco frequency generator' block on the iomod10f module generates a very accurate 'calibration frequency' which is used during the 'xtal calibration procedure'...
Page 14
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 4 1.4 iomod10f module - control methods the table below outlines possible methods of controlling the 'iomod10f' module..... # control method further information / instructions 1 equinox ispnano programm...
Page 15: 2.1 Ordering Information
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 5 2.0 iomod10f - general product information 2.1 ordering information this table below details the order codes for the various iomod calibration systems.... See section kit order code further informatio...
Page 16
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 6 module with an on-board 3.3v power supply if you are using the iomod10f module with an external programmer from sigma, then please refer to the new eq-rbk-zwavecalibox-3 kit. 2.3 sigma eq-rbk-zwavecal...
Page 17
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 7 2.4 iomod10f module - hardware layout the illustration below shows the relevant hardware items on the ‘iomod10’ module...... Pcb label diagram # functional description connectors j2 10 dc power input ...
Page 18
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 8 lk3 12 tvcc (target power) status led - enable (fit jumper to enable led) lk4 6 external nvm spi memory device - 'chip select (cs)' - enable fit jumper link to connect programmer 'io4' pin to the targ...
Page 19
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 9 2.5 iomod10f module - connector overview the connectors on the iomod10f module are detailed in the table below. J5 spi equinox standard 10-way 0.1" pitch idc box header spi interface pin-out spi inter...
Page 20
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 10 2.6 iomod10f - connecting to a z-wave target system the illustrations below detail the connections required between the iomod10f module and the target 500 series z-wave device for both the 'spi inter...
Page 21
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 11 2.7 iomod10f - configuration jumper link settings the ‘iomod10f’ module features 4 x 'configuration jumper links' which are used to configure the module for the programming application. Pcb label dia...
Page 22
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 12 2.7.2 configuration jumper lk2 - calibration clock output pin selection the 'lk2' jumper link is used to select which output pin on the iomod10f module the 'calibration frequency' will be output on. ...
Page 23
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 13 important note: the 'target power' is independent of the 3.3v supply which the iomod10f circuitry is actually running from. 2.7.4 configuration jumper lk4 - nvm cs (chip select) the jumper link lk4 c...
Page 24
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 14 2.8 iomod10f module - status led's the iomod10f module features 3 x 'status leds' as shown in the illustration below.... The function of each 'status led' is explained in the table below.... Led colo...
Page 25
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 15 2.9 oxco - oscillator module (temperature compensated) the 'oxco oscillator module' fitted to the iomod10f module is a temperature-compensated component. It requires a minimum of 90 seconds to come u...
Page 26
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 16 2.10 operating specifications the table below details the main operating characteristics of the iomod10f module. Parameter minimum nominal maximum units notes temperature range 0 25 70 deg. C supply ...
Page 27: 1.0 Overview
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 17 appendix 1 - using iomod10f module with ispnano series 4 programmer 1.0 overview this appendix describes how to use the 'iomod10f' module with an equinox ‘ispnano series 4’ programmer. Important note...
Page 28
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 18 1.1 fitting the iomod10f module to the ispnano programmer the ‘iomod10f’ module fits onto the 'ispnano series 4 ate' programmer as shown in the picture below..... Instructions: • position the ‘iomod1...
Page 29
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 19 1.2 powering the iomod10f module a programming / calibration system using the 'ispnano series 4 ate' and the 'iomod10f - oscillator calibration module', requires two independent power supplies. One p...
Page 30
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 20 the illustration below shows how to connect an external power supply to the iomod10 module via a 2.1 mm centre positive jack socket. Please note: a suitable 3.3v dc regulated @ 1.8a power supply for ...
Page 31
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 21 1.4 power sequencing instructions for the iomod10f module it is very important to follow the power sequencing instructions below when setting up the iomod10f module / programmer ready for a productio...
Page 32: 1.0 Overview
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 22 appendix 2 - iomod10f 'carrier board' 1.0 overview it is possible to use the iomod10f - sigma calibration module without using an equinox ispnano programmer. This allows the module to be used for per...
Page 33
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 23 1.1 iomod10f - carrier board - features the main features of the 'iomod10f carrier board' are as follows: • simple 'carrier board' which allows the 'iomod10f - sigma calibration module' to be used wi...
Page 34
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 24 1.2 iomod10f - carrier board - hardware layout pcb label diagram # description connectors j3 7 programming / calibration signals connector type: 10-way idc - equinox / sigma pin-out purpose: connect ...
Page 35
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 25 miscellaneous - 2 this is where the iomod10f module is located when fitted. - 4 this is where the circuitry for the 3.3v power supply is located on the iomod10-cb1 v2.0 board..
Page 36
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 26 1.3 powering the iomod10f module via the carrier board the new version 2.0 of the 'carrier board' now has an on-board 3.3v power supply which generates a very accurate and stable 3.3v supply to power...
Page 37
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 27 instructions: the instructions detailed below explain how to connect power to the iomod10f / carrier board combination. Steps 1 - 3 should already have been carried out by equinox so you can start at...
Page 38: 1.1 Overview
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 28 appendix 3 - interfacing the iomod10f carrier board to the sigma eval module 1.1 overview the ‘iomod10f module’ can be interfaced to the ‘sigma eval module / programmer’ by using the 'iomod10 carrier...
Page 39: 1.0 Overview
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 29 appendix 4 - interfacing the iomod10f module to a z-wave target system 1.0 overview this section details how to connect the iomod10f module to a z-wave target system. The iomod10f module supports the...
Page 40: Connections
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 30 1.1 iomod10f - spi interface via separate wired signal connections the illustration below shows how to connect the iomod10f module to a 500 series z-wave target board (dut) via the 'spi programming i...
Page 41
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 31 1.2 iomod10f - spi interface via 10-way idc connector the illustration below shows how to connect the iomod10f module to a 500 series z-wave target board (dut) via the 'spi programming interface' usi...
Page 42: Connections
Iomod10f calibration module for z-wave 500 series ic and modules - user manual - v2.06 06/10/2017 32 1.3 iomod10f - uart interface via separate wired signal connections the illustration below shows how to connect the iomod10f module to a 500 series z-wave target board (dut) via the 'uart programming...