User's manual ver. 130620 to ensure safe and easy installation, please read the following precautions. Www.Zalman.Com fx100 amd socket fm2 / fm1 / am3+ / am3 / am2+ / am2 cpu&apus intel socket lga 2011 / 1366 / 1156 / 1155 / 1150 / 775 cpus * optional 92mm fan is required for intel lga 2011/1366 soc...
1 .Com 2. Specifications 1. Precautions 1) do not ingest the thermal grease, and avoid its contact with skin and eyes. If contact is made with skin, wash off with water. If ingested or irritation persists, seek medical attention. 2) to prevent possible injuries, gloves must be worn while handling th...
2 .Com nipple a fan clip nuts thermal grease bolts manual loading block intel washer (0.1mm) amd washer (1mm) double-sided tape backplate nipple b clip support cooler nuts & side caps installation clip 3. Components.
3 .Com 4. Installation requirements 1) space requirments 2) air guide removal 3) cooler orientation the cooler’s installation requires an unobstructed space of 156mm(width), 156mm(length), and 157mm(height), with the cpu as a central reference point. Please check if components such as odds and psu p...
4 .Com 5. Installation a. Intel socket installation ※ make sure to install the clip support by following specific instructions based on your cpu socket. ※ optional fan is required for lga 2011 socket cpus. (fan sold separately) 1) intel socket 2011 installation ① fasten nipple b to the clip support’...
5 .Com 1 2 2) intel socket lga 1366/1156/1155/1150 installation socket 775 socket 1156/1155/1150 socket 1366 ② attach double-sided tape to the center of the backplate and remove the double-sided tape’s cover. ※ socket lga 1366/1156/1155/1150 installation does not require the loading block. ① install...
6 .Com 3) intel socket 775 installation ① install bolts to the backplate according to the socket type and secure with side caps. ③ attach double-sided tape to the loading block and remove the double-sided tape cover. ② remove the sticker cover from the lower tier of the loading block and attach it t...
7 .Com ④ align the backplate’s nuts with motherboard’s clip support holes, attach it to the back side of the motherboard, and then fix it with intel’s washer(0.1mm) and nipple a. Intel washer ⑤ install the clip support on the motherboard using nuts. Nut clip support please make a note of the orienta...
8 .Com 1) amd socket fm2/fm1/am3+/am3/am2+/am2 installation b. Amd socket installation ① install bolts to the backplate according to the socket type and secure with side caps. ② remove the sticker cover from the lower tier of the loading block and attach to the backplate. ③ attach dobule-sided tape ...
9 .Com amd washer nut clip support ④ take away the fixed clip support from the motherboard, and then install the included clip support using nipple a, amd’s washer(1mm) and nuts. ※after installing the clip support, please mount the cpu cooler as following. C. Cooler installation ① apply a suitable a...
10 .Com ② take off the heatsink cover and remove the protection pad. ③ place installation clip on top of the base cover, and secure it by screwing down two bolts on each end of installation clip. ④ place the heatsink cover back on the cooler. Bolt heatsink cover protection pad.
11 .Com ※users must purchase the optional 92mm fan for installation (zalman zm-f2q(bl) fan is recommended) d. Optional fan installation ① take off the heatsink cover installed on the cooler. ② attach two fan clips to the top mounting holes on the fan. Then, vertically insert the fan to the center of...
12 .Com ③ place the heatsink cover back on the cooler. ④ connect the cooler’s 4-pin connector to the motherboard’s option fan header. After installing, be sure to activate the pwm control mode in bios on the motherboard. Caution m/b.
