Summary of HD501
Page 1
English.
Page 3: Hd500 Series
1 english 1 hd500 series (1) please read this manual thoroughly prior to installation. (2) before installing, check the components and condition of the product, and if any problem is found, contact the retailer. (3) avoid inserting objects or hands into the system while it is in operation to prevent...
Page 4: Hd500 Series
2 2 hd500 series models hd501 hd503 enclosure type htpc dimensions (w×h×d) 450 × 170 × 455mm (17.6” x 6.8” x 17.9”) weight main unit: 8kg(17.6lb) / with packaging: 9.6kg(21lb) materials aluminum / plastic / steel color black / silver compatible motherboards standard atx / matx compatible psus standa...
Page 5: Hd500 Series
3 english 3 hd500 series components (1) main unit top panel top panel hdd chassis hdd chassis odd chassis odd chassis main chassis main chassis hd501 hd503.
Page 6: Hd500 Series
4 hd500 series (2) parts [hd501, hd503] 13 x motherboard/ psu bolts 2 × matx standoffs 1 x clamp 10 x cable ties 1 x user’s manual 1 x lock plate bolt 1 x lock plate 4 x odd bolts 4 x ssd bolts 2 x hdd bolts (hot swap bay) (3) imon components [hd503] remote control installation cd 2 x batteries(aaa)...
Page 7: Hd500 Series
English 5 hd500 series 4 ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ① lcd & ir receiver ② power button ③ power led ④ reset button ⑤ hdd led ⑥ media control button ⑦ volume control knob ⑧ front i/o port ⑨ hdd hot swap bay ⑩ 5.25” odd bay ① power button ② power led ③ reset button ④ hdd led ⑤ front i/o port ⑥ hdd hot swap ba...
Page 8: Hd500 Series
5 6 hd500 series installation (1) installation preparation 1) unfasten the rear screws and remove the top panel. 2) unfasten the two screws (top and side) holding the odd chassis. With the side button pressed, push the odd chassis towards the rear to remove. Push 1 2.
Page 9: Hd500 Series
English 7 hd500 series 3) unfasten the hdd chassis’ handscrew (top) and fixing screw (bottom) ,then move sequentially in the directions as indicated by the numbered arrows in the diagram to remove. Install the motherboard (with cpu, ram etc. Installed) and psu. Psu (2) motherboard and psu installati...
Page 10: Hd500 Series
8 hd500 series matx standoff (3) odd installation install the odd into an available slot in the odd chassis and fasten with odd bolts. Tip if the motherboard is of the matx standard, please install the matx standoffs before motherboard installation. Odd odd bolt.
Page 11: Hd500 Series
English 9 hd500 series to remove handle, pull upwards while pressing the hook button. Use the hand screws to attach the handle to the hdd. Push the hdd into the slot until there is a “click” sound. (4) 3.5 ” hdd installation hdd hdd tip ▶ hdd removal is possible without removing the hdd chassis from...
Page 12: Hd500 Series
10 hd500 series insert the ssd in the ssd bracket and fasten with ssd bolts. Reattach the hdd handle to the ssd bracket. Push the ssd into the slot until there is a “click” sound. Two ssd’s can be installed on a single bracket. Installing hdd’s to the bottom rung can cause short circuiting so please...
Page 13: Hd500 Series
2 english 11 hd500 series if the case is frequently transported, please fasten the odd chassis (top) and hdd chassis (bottom) before use. Tip (6) odd/hdd chassis assembly 1) push the odd chassis into its slot until there is a “click” sound and fasten with hand screws. 2) push the hdd chassis into it...
Page 14: Hd500 Series
12 hd500 series (7) hot swap bay installation 1) hdd tray removal 2) 3.5” hdd installation ‘open’ the hot swap tray by pressing the hot swap tray’s hooks located on the underside, and pushing in the direction as shown the diagram. While squeezing and holding the hot swap tray’s hook in ‘direction 1’...
Page 15: Hd500 Series
English 13 hd500 series align the hdd’s screw holes with the hot swap trays fixing pins, then ‘close’ the hot swap tray by pushing in the protruded section. Check that the hot swap tray’s fixing pins and the hdd’s holes are properly aligned and fastened. Fully insert the hdd installed hot swap tray ...
Page 16: Hd500 Series
14 hd500 series 3) hot swap cable connection s-ata port 4 pin power port (hdd) 4-pin power port (fan) 3-pin fan connector fan speed control switch (up: 12v/ down: 5v) the s-ata cable and power cable must be connected to the s-ata port and 4-pin power port before powering on. For stable operation, pl...
Page 17: Hd500 Series
English 15 hd500 series 2) dfstn and media controller cable connections [hd503] 1) front panel i/o cable connections [hd501, hd503] e-sata usb hd audio ac’97 audio ① usb(4/5-pin) ② power(2-pin) ③ power led(2/3-pin) ④ reset(2-pin) ⑤ hdd led(2-pin) ⑥ standby power(20/24-pin) (8) cable connections ① ② ...
Page 18: Hd500 Series
6 16 hd500 series optional fan installation unfasten the fixing bolts and press the hooks towards each other to pull the side panels off. Install the 2 x 120mm fans to the locations shown in the diagram. Intake fan exhaust fan.
Page 19: Hd500 Series
7 english 17 hd500 series recommended use 1) installation location 2) cable routing for adequate air flow, please install the system in a well ventilated area. Low air flow can cause high fan rpm, which can create unwanted noise. O o x please use the provided clamp and cable ties for cable managemen...
Page 20: Hd500 Series
18 hd500 series memo.