Zamel GRL-01 Instruction Manual
VER. 007_22.08.2011
LAN REMOTE SWITCH GRL-01
MANUAL INSTRUCTION
The device is designed for
single-phase
installation
and must be installed in
accordance with standards
valid in a particular country.
The device should be con-
nected according to the de-
tails included in this operat-
ing manual. Installation, connection and control
VKRXOGEHFDUULHGRXWE\DTXDOL¿HGHOHFWULFLDQ
staff, who act in accordance with the service
manual and the device functions.
In case of casing dismantling an electric shock
may occur, and the guarantee is lost then. Be-
fore installation make sure the connection ca-
bles are not under voltage. The cruciform head
screwdriver 3,5 mm should be used to instal the
device. Improper transport, storage, and use of
WKHGHYLFHLQÀXHQFHLWVZURQJIXQFWLRQLQJ,WLV
not advisable to instal the device in the following
cases: if any device part is missing or the device
is damaged or deformed. In case of improper
functioning of the device contact the producer.
CAUTION!
APPEARANCE
FEATURES
TECHNICAL DATA
DESCRIPTION
Ɣ UHPRWH FRQWURO RI HOHFWULF GHYLFH RSH-
ration by means of computer network
commands - by means of web browser,
Ɣ FRPIRUWDEOHFRQWURORIGHYLFHVZLWKGLI¿-
cult access (ventilation, heating, other),
Ɣ WKUHH RSHUDWLRQ PRGHV VZLWFKLQJ RQ
switching off, restart - contact relay po-
sition change for adjusted time),
Ɣ SRVVLEOH FRRSHUDWLRQ ZLWK VWDQGDUG QH-
twork devices (routers, switches, etc.)
Ɣ 66/SURWRFROVHFXUHVFRQQHFWLRQ
Ɣ HDV\PRXQWLQJLQ9$&VRFNHW
Remote switch LAN is used to control
lighting, heating, etc. by means of ether-
net (web browser). The switch is mounted
in a 230 V~ socket and it has a possibility
of a remote restart (relay status change
at the adjusted time) of the connected de-
vice, which is done by means of a safe
SSL protocol.
GRL-01
Input rated voltage: 230 V~
Input voltage tolerance: -15 ÷ +10 %
Nominal power consumption: 2 W
Optic signalling of input (supply): LED green diode
Number of operation modes: 3
Accepted communication protocols: IP, TCP, UDP, HTTP, HTTPS, DHCP, ARP
Coding: SSL code connection
Connection parameters (Link): 10 Mbps / Full Duplex
LAN socket type: RJ 45
Optic signalling of relay status: LED red diode
Output contacts parameters: 1NO 16A / 250V~ AC1 4000 VA
Ambient temperature range: -10 ÷ +55
o
C
Operating position: free
Casing mounting: 230 V~ socket
Casing protection degree: IP20 (EN 60529)
Protection level: II
Overvoltage category: II
Pollution degree: 2
Surge voltage: 1 kV (EN 61000-4-5)
Dimensions: 160 x 66 x 90 mm
Weight: 0,170 kg
Reference standard: EN 60950-1:2007,
EN 55024:2000,
EN 610004-4
The symbol means selective
collecting of electrical and
electronic equipment.
It is forbidden to put the used
equipment together with other
waste.
Optic signalling of receiver’s switch on
Relay manual control
LAN (RJ 45) socket
Receiver’s slot
Power supply plug
Optic signalling of input voltage
ZAMEL Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04
www.zamelcet.com, e-mail: marketing@zamel.pl