Zamel P-257/2 Manual Instruction - page 2
VER. 003_20.05.2011
COOPERATION AND OPERATING RANGE
Symbol
ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTI-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
*-1-channeltransmittersdonotcooperatewithrollerblindcontrollers.
CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%,
glass: from 10 to 20 %, Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have
also a negative influence on the range.
RADIO TRANSMITTERS PROGRAMMING
ROP-01 OPERATION
ROP-01canoperateinfivemodes:
MONOSTABLE
the relay operates only
while pressing transmit-
ter’spush-button.
BISTABLE
(one push-button) the
device changes relay
statuscyclicallyalways
after pressing the same push-
-button.
SWITCH ON
the device switches on
afterpressingthepush-
-button.
SWITCH OFF
the device switches off
afterpressingthepush-
-button.
TIME
the device switches
off according to the
adjusted time (tp),
butitmaybeswitchedoffbefore
adjusted time finishes. Default
settings - 15 seconds.
CAUTION! Adjusted time can
not be deleted.
TIME PROGRAMMING
RADIO TRANSMITTERS DELETION
TRANSMITTERS
RECEIVERS
RNK-02
2–channelbutton
radio transmitter
RNL-01
Radio
foot transmitter
ROP-01
1-channel
radioreceiver
RWL-01
Radiolighting
switch
RNK-04
4-channelbutton
radio transmitter
RTI-01
IR/EXTAFREE
transceiver
ROP-02
2-channel
radioreceiver
RWG-01
Remote control
socket
P-256/8
8-channel
remote controller
RNM-10
4-channelradio
modular transmitter
RDP-01
1-channel
radio dimmer
SRP-02
Radio roller blinds
controller
P-257/4
4-channel
remote controller
RNP-01
4-channel
radio transmitter
ROB-01/12-24V
Radio
gate controller
SRP-03
Central radio roller
blinds controller
P-257/2
2-channel
remote controller
RNP-02
4-channel
radio transmitter
ROM-01
1-channelradio
modularreceiver
ROM-10
2-channel
radiomodularreceiver
RCR-01
Radio
motion sensor
RXM-01
Translator
RS-485/EXTAFREE
ACCESSORIES
ANT-01
External antenna
RTN-01
Retransmitter
MONOSTABLE mode:
BISTABLE mode:
SWITCH ON/SWITCH OFFmode(twopush-buttons):
TIMEmode(onepush-button):
AnexemplaryprogrammingprocedurewiththeuseofP-257/2remotecontroller.TheprocedurefortherestofradioEXTAFREEtransmitters
is analogous.
CAUTION: Every transmitter can cooperate with ROP-01 in a different mode, depending on how they were added to
the device. One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode.
Press transmitter’s
push-buttonfor
a longer time.
Pressthetransmitter’spush-button
for a longer time. LED red diode
switcheson(firstsignalpulsates,
nextthesignalisconstant).
Presstransmitter’spush-buttonandthen
releaseit.LEDreddiodeswitcheson
(firstsignalpulsates,next
thesignalisconstant).
Press and release transmitter’s
push-button.LEDreddiode
switcheson(firstsignalpulsates,next
thesignalisconstant).
Releasetransmitter’spush-
button.LEDreddiodeswitches
on(firstsignalpulsates,
nextthesignalisconstant).
Releasetransmitter’spush-button.
LEDreddiodeswitcheson(the
signalpulsates),nexttheLEDred
diodeswitchesoff-itmeansthe
TRANSMITTER IS ADDED.
Pressandreleasethesametransmitter’s
push-button.LEDreddiodeswitcheson
(signalpulsates)andthenswitchesoff-
THE TRANSMITTER IS ADDED.
Pressandreleasethesametransmitter’s
push-button.LEDreddiodeswitcheson
(thesignalpulsates)andnextitswitches
off - THE TRANSMITTER IS ADDED.
Pressthesametransmitter’spush-
-button and release it. LED red
diodeswitcheson(thesignalpulsa-
tes)andnextitswitchesoff-THE
TRANSMITTER IS ADDED.
PressPROGpush-buttonofROP-01device
for a longer time until LED red diode
switcheson(constantsignal).
NextreleasePROGpush-button.
PressPROGpush-buttonofROP-01device
for a longer time until LED red diode
switcheson(constantsignal).
NextreleasePROGpush-button.
PressPROGpush-buttonofROP-01device
for a longer time until LED red diode
switcheson(constantsignal).
NextreleasePROGpush-button.
PressPROGpush-buttonofROP-01device
for a longer time till LED red diode
switcheson(constantsignal).
NextreleasePROGpush-button.
Maximumtimeis18hours.
PressPROGpush-buttonofROP-01deviceforalongertimetill
LEDreddiodeswitcheson(constantsignal).NextreleasePROG
push-button.Wait(forabout5seconds)tillLEDreddiodeswitches
on(firstsignalpulsates,nextthesignalisconstant).
Aftertheadjustedtimeis
finished(thenumber
ofLEDreddiodeflashes)
pressPROGpush-button
andthenreleaseit
- TIME IS ADDED.
PressPROGpush-buttonofROP-01device
andthenreleaseit.LEDreddiodeswitches
offandthenswitcheson(signalpulsates).
EveryLEDdiodepulseequals1second.
PressPROGpush-buttonofROP-01
deviceforalongertime.
After5secondsLEDreddiodeswitcheson
(signalpulsates)andthenitswitchesoff.
Releasethepush-buttoninROP-01-
MEMORY IS DELETED.
1s 2s
ns