Zamel ROP-01 Manual Instruction

1-CHANNEL RADIO RECEIVER ROP-01

MANUAL INSTRUCTION

ZAMEL Sp. z o.o.

ul. Zielona 27, 43-200 Pszczyna, Poland

tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04

www.zamelcet.com, e-mail: marketing@zamel.pl

VER. 005_20.05.2011

APPEARANCE

The device is designed for 

single-phase installation and 

must be installed in accord-

ance with standards valid in  

a particular country. The de-

vice should be connected 

according to the details in-

cluded in this operating manual. Installation, 

connection and control should be carried out by  

a qualified electrician staff, who act in accord-

ance with the service manual and the device 

functions. Disassembling of the device is equal 

with a loss of guarantee and can cause elec-

tric shock. Before installation make sure the 

connection cables are not under voltage. The 

cruciform head screwdriver 3,5 mm should be 

used to instal the device. Improper transport, 

storage,  and  use  of  the  device  influence  its 

wrong functioning. It is not advisable to instal 

the device in the following cases: if any device 

part is missing or the device is damaged or de-

formed. In case of improper functioning of the 

device contact the producer.

CAUTION

FEATURES

TECHNICAL DATA

DESCRIPTION

●  cooperation with wireless EXTA FREE 

control system transmitters,

●  1 NO/OC output relay (dry contacts),

●  lighting, heating operation control,

●  easy junction box Ø 60 mm installation,

●  5 operation modes: switching on, swit-

ching off, monostable mode, bistable 

mode, time mode  (switch off delay),

●  wide operation range (up to 230 m),

●  operation is optically signalled, 

●  low current consumption, possibility of 

constant operation,

●  possibility of increasing operation ran-

ge by means of RTN-01 retransmitter.

Radio receivers are used both as el-

ements in mounting in flush and surface 

installation cable boxes and as an ac-

tuator built directly in lighting fittings and 

other receivers. ROP-01 enables opera-

tion in 5 different modes (switching on, 

switching off, monostable mode, bistable 

mode, time mode.)

ROP-01

Input (supply) terminals: L, N

Input rated voltage: 230 V AC

Input voltage tolerance: -15 ÷ +10 %

Nominal frequency: 50 / 60 Hz

Nominal power consumption: 0,29 W

Number of operation modes: 5

Number of channels: 1

Transmission: radio 868,32 MHz

Transmission way: unidirectional

Coding: addressing transmission

Maximum number of transmitters: 32

Range: up to 230 m in the open air

Time adjustment: 1 second ÷ 18 hours (every second)

Optical signalling of transmitter’s operation: red LED diode

Relay output clamps: 12, 11, 14

Relay contacts parameters: 1NO/NC 5A / 250V~ AC1 1250 VA

Number of terminal clamps: 5

Section of connecting cables: up to  2,5 mm

2

Ambient temperature range: -10 ÷ +55 

o

C

Operating position: free

Casing mounting: junction box Ø 60 mm

Casing protection degree: IP20 (EN 60529)

Protection level: II

Overvoltage category: II

Pollution degree: 2

Surge voltage: 1 kV (EN 61000-4-5)

Dimensions: 47,5 x 47,5 x 20 mm

Weight: 0,043 kg

Reference standard: EN 60669, EN 60950, EN 61000

The symbol means selective 

collecting of electrical and electronic 

equipment. It is forbidden to put 

the used equipment together with 

other waste.

Optical signalling of receiver’s operation

Programming buttons

Relay output terminals  

(12, 11, 14)

Input (supply) terminals (L, N)

CONNECTION

APPLICATION

1-channel radio receiver 

ROP-01 operates as a receiv-

er of 8-channel remote con-

troller P-256/8 and of 2-chan-

nel button radio transmitter 

RNK-02 (light sources switch  

on/switch off control). 

The above mentioned trans-

mitters can also control op-

eration of radio lighting switch 

RWL-01 and remote control 

socket RWG-01.

CAPACITY

750W

250W

500W

375W

MOUNTING

1. Disconnect power supply by the 

phase fuse, the circuit-breaker  or 

the switch-disconnector combined 

to the proper circuit.

2.  Check if there is no voltage on 

connection cables by means of 

a special measure equipment.

3. Connect  the cables with the termi-

nals in accordance with the install-

ing diagram.

4. Install ROP-01 device in installa-

tion cable box.   

5. Switch on the power supply from 

the mains.

WARRANTY CARD

There is 24 months guarantee on the product

1.  ZAMEL provides a two-year warranty for its products. 

2.  The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances  

b) defects resulting from incorrect installation or operation of ZAMEL products; c) defects resulting from any changes made by CUS-

TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold; d) defects resulting 

from force majeure or other aleatory events for which ZAMEL is not liable; e) power supply (batteries) to be equipped with a device 

in the moment of sale (if they appear); 

3.  All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.; 

4.  ZAMEL will review complaints in accordance with existing regulations.; 

5.  The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 

6.  Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy 

between the goods and the contract.

Salesman stamp and signature, date of sale

The ZAMEL company devices which 

are characterised with this sign can 

cooperate with each other.