Zanussi ZDF4013 User Manual

Other manuals for ZDF4013: User Manual
Manual is about: Product Manaul

Summary of ZDF4013

  • Page 1

    En user manual dishwasher zdf 4013.

  • Page 2

    Contents safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 before first ...

  • Page 3

    • do not change the specification of this appliance. • put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. • do not keep the appliance door open without supervi- sion to prevent to fall on it. • do not sit or stand on the open door. • dish...

  • Page 4

    Control panel 1 3 5 4 2 6 a b c d e 1 on/off button 2 programme buttons 3 delay button 4 indicators 5 display 6 function buttons indicators description wash indicator. End indicator. Multitab indicator. Salt indicator. This indicator is off while the programme operates. Rinse aid indicator. This ind...

  • Page 5

    Programmes programme 1) degree of soil type of load programme phases duration (min) energy (kwh) water (l) heavy soil crockery, cutlery, pots and pans prewash wash 70 °c rinses dry 80 - 90 1.6 - 1.8 22 - 24 2) all crockery, cutlery, pots and pans prewash wash 45 °c or 70 °c rinses dry 90 - 140 1.1 -...

  • Page 6

    2. Make sure that the appliance is in setting mode. Refer to ‘setting and starting a programme'. 3. Press and hold function buttons (d) and (e) at the same time until the multitab indicator comes on. The function stays on until you deactivate it. Press and hold function buttons (d) and (e) at the sa...

  • Page 7

    Water hardness water softener adjustment german degrees (°dh) french degrees (°fh) mmol/l clarke degrees manual electronic 4 - 10 7 - 18 0.7 - 1.8 5 - 12 1 2 1 2) 1 2) 1) factory position. 2) do not use salt at this level. Manual adjustment 1 2 turn the water hardness dial to the position 1 or 2. El...

  • Page 8

    Filling the rinse aid dispenser caution! Only use rinse aid for dishwashers. Other products can cause damage to the appliance. The rinse aid, during the last rinsing phase, helps to dry the dishes without streaks and stains. 1 2 max m a x 1 2 3 4 + 3 4 m a x 1 2 3 4 + to adjust the released quantity...

  • Page 9

    Using the detergent caution! Use only detergents for dishwashers. Do not use more than the correct quantity of deter- gent. Refer to the instructions on the detergent packaging. 1 2 a 3 put the detergent or the tablet in compartment (a). A b if the programme has a prewash phase, put a small quantity...

  • Page 10

    You can set a programme, options and the delay start also with the appliance door closed. In this condition, you only have 3 seconds after each setting be- fore the appliance starts to operate. Opening the door while the appliance operates if you open the door, the appliance stops. When you close th...

  • Page 11

    D a 5 put filter (a) to its initial position. Make sure that it assembles correctly under the two guides (d). 6 assemble filters (b) and (c). Put them into position in filter (a). Turn the han- dle clockwise until it locks. An incorrect position of the filters can cause bad washing results and damag...

  • Page 12

    Problem possible cause possible solution the appliance does not drain the water. The sink spigot is clogged. Clean the sink spigot. The water drain hose has a kink or a bend. Make sure that the position of the hose is correct. After the checks are completed, activate the appliance. The programme con...

  • Page 13

    Problem possible cause possible solution the quantity of detergent was too much. Make sure that you add the correct quan- tity of detergent in the dispenser before you start a programme. Dry water drop stains on glasses and dishes. The released quantity of rinse aid was not sufficient . Increase the...

  • Page 14

    Capacity place settings 12 power consumption left-on mode 1.90 w off-mode 0.10 w 1) connect the water inlet hose to a water tap with a 3/4'' thread. 2) if the hot water comes from alternative sources of energy, (e.G. Solar panels, aeolian energy), use the hot water supply to decrease energy consumpt...

  • Page 15

    15 www.Zanussi.Com.

  • Page 16

    Www.Zanussi.Com/shop 1569 59610-a-032012.