1. DL manuals
  2. Zanussi
  3. Hob
  4. ZGF 642 CTN
  5. Instruction Booklet

Zanussi ZGF 642 CTN Instruction Booklet

Summary of ZGF 642 CTN

  • Page 1

    Gas hobs zgf 642 ctn zgf 642 ctx instruction booklet please read this instruction booklet before using the appliance gb ie.

  • Page 2: Important Safety Information

    2 guide to use the instructions the following symbols will be found in the text to guide you throughout the instructions: safety instructions step by step instructions for an operation hints and tips environmental information important safety information you must read these warnings carefully before...

  • Page 3: Description of The Hob

    3 1. Hob top 2. Auxiliary burner 3. Semi-rapid burners 4. Rapid burner 5. Control knobs description of the hob this appliance complies with the following e.E.C. Directives: * 73/23 - 90/683 (low voltagedirective); * 93/68 (general directives); * 89/336 (electromagnetical compatibility directive); * ...

  • Page 4: Operation

    4 operation a - burner cap b - burner crown c - ignition electrode d - thermocouple burner minimum maximum diameter diameter large (rapid) 180 mm 260 mm medium (semi-rapid) 120 mm 220 mm small (auxiliary) 80 mm 160 mm hob burners to light a burner: z turn the relevant control knob anticlockwise to t...

  • Page 5: The Hob Top

    5 before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top using a soft cloth well wr...

  • Page 6: Something Not Working?

    6 something not working? If the hob is not working correctly, please carry out the following checks before contacting your local zanussi service force centre. Important: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will b...

  • Page 7: Zanussi Guarantee Conditions

    7 zanussi guarantee conditions we, zanussi, undertake that if, within 24 months of the date of the purchase, this zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same free of any char...

  • Page 8: Engineers Technical Data

    8 rear left burner (semi rapid) heat input 2.0 kw (6824 btu/hr) front left burner (auxiliary) heat input 1.0 kw (3412 btu/hr) rear right burner (semi rapid) heat input 2.0 kw (6824 btu/hr) front right burner (rapid) heat input 3.0 kw (10236 btu/hr) instructions for the installer engineers technical ...

  • Page 9: Provision For Ventilation

    9 important safety requirements 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm i clearances required when fitting the hob without a cooker hood above clearances required when fitting the hob with a cooker hood above fo 0813 fo 0812 700 mm this hob ...

  • Page 10: Gas Connection

    10 rectangular cut-out size for hob a) end of shaft with nut b) washer c) elbow fo 0814 gas connection connection to the gas supply should be with either rigid or semi-rigid pipe, i.E. Steel or copper. The connection should be suitable for connecting to rc 1/2 (1/2 bsp male thread). When the final c...

  • Page 11: Building In

    11 on/off switch flex outlet on/off switch flex outlet fo 0763 fo 2564 fo 2044 1 2 3 fo 0199 a fitting the hob into the worktop ) carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them along the side edges and at 8 mm from the ...

  • Page 12: Electrical Connections

    12 electrical connections any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This hob must be earthed. The manufacturer declines any liability should these safety measures not be observed....

  • Page 13: Fault Finding

    13 fault finding preliminary electrical systems check a. Earth continuity check - appliance must be electrically disconnected - meter set on Ω (ohms) x 1 scale and adjust zero if necessary. A) test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (ohm),...

  • Page 14

    14 ignition system / gas ignition yes check plug top fuse and replace if necessary check polarity and earth continuity of supply point check earth continuity of appliance ignitor does not spark check fitting of burners check position of the electrode check by pass simmer light burner manually check ...

  • Page 15: To Adjust The Gas Rate

    15 conversion from natural gas to lpg important the replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct inject...

  • Page 16

    Grafiche mdm - forlì 35687-7901 09/04 from the electrolux group. The world’s no.1 choice. The electrolux group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million electrolux group products (such as refrigerators, cookers, washing machines...