Summary of ZGF 646
Page 1
Gas hobs zgf 646 operating and installation manual.
Page 2: English
2 • this appliance has been designed to be operated by adults and children under supervision. Young children must not be allowed to tamper with the controls or play near or with the oven. • this appliance has been designed for cooking edible foodstuff and to be used for domestic non- professional pu...
Page 3: 1. Instruction For The User
3 1. Instruction for the user hob burners control knobs the hob burners control knobs are situated on the hob front panel. The symbols on the knobs mean that : ● there is no gas supply there is maximum gas supply there is minimum gas supply lighting the burners • for easier lighting, proceed before ...
Page 4: 2. Cleaning and Maintenance
4 2. Cleaning and maintenance • disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. General cleaning wash the enamelled components with warm soapy water. Never use abrasive cleaners frequently wash the "caps" and the "crowns" with hot soapy wate...
Page 5: 3. Periodic Maintenance
5 periodically ask your local service centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. Original spare parts this machine, before leav...
Page 6: 5. Technical Data
6 5. Technical data gas burners rating rapid burner (big) 2,9 kw semirapid burner (medium) 1,9 kw auxiliary burner (small) 1,1 kw category ii2hs3b/p setting natural gas g 20 25 mbar gas connection g 1/2" electric supply 230 v 50 hz hob recess dimensions length 560 mm. Width 480 mm. 6. Instruction fo...
Page 7: 7. Electrical Connection
7 the appliance is designed to be connected to 230 v monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the ratin...
Page 8
8 adjustment of minimum level to adjust the minimum level of the burners, proceed as follows: • light the burner. • turn the knob on the minimum position. • remove the knob. • with a thin screwdriver, adjust the by-pass screw (see fig. 10). If changing from natural gas to lpg, completely tighten clo...
Page 9: 9. Building In
9 type type of injectors nominal reduced nominal nominal of gas burner marks power power power pressure 1/100 mm input kw mbar kw m 3 /h g/h rapid (large) 112 2,9 0,65 0,276 - semi-rapid (medium) 92 1,9 0,45 0,180 - 25 auxiliary (small) 70 1,1 0,33 0,104 - rapido (grande) 86 2,8 0,65 - 203 semirapid...
Page 10
10 fitting the lid we recommend the lid hinge block are fitted before installing the hob into the worktop. To install the lid onto the hob, proceed as follows: a. Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (fig. 12) b. Fit the lid hing...
Page 11
11 installation and assembly these hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in fig. 15. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the ...
Page 12
12 480 30 591 380 140 360 cm 2 50 cm 2 120 cm 2 180 cm 2 30 20 min 60 a b possibilities for insertion kitchen unit with door proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recomm...