Summary of ZGF 759
Page 1
2 gas hob model zgf 759 instruction booklet.
Page 2: Important Safety Information
3 important safety information you must read these warnings carefully before installing or using the appliance. Installation ● this appliance must be installed by qualified personnel, according to the manufacturer ’s instructions and to the rules in force. ● remove all packaging before using the app...
Page 3: For The User
4 for the user description of the hob page 5 operation page 6 maintenance and cleaning page 7 something not working page 8 contents for the installer technical data page 9 installation page 10 gas connection page 10 building in page 11 fitting the hob to the worktop page 12 electrical connection pag...
Page 4: Description of The Hob
5 1. Hob top 2. Auxiliary burner 3. Semi-rapid burners 4. Rapid burner 5. Ignition pushbutton 6. Control knob for front left burner (auxiliary) 7. Control knob for back left buner (semi-rapid) 8. Control knob for central burner (rapid) 9. Control knob for back right burner (semi-rapid) 10. Control k...
Page 5: Operation
6 operation to light a burner, turn the relevant control knob anticlockwise to maximum position and push it down to ignite. Keep the control knob pressed down for about 5 seconds, to allow the safety device to be switched off. Then adjust the flame as required. If the burner does not ignite, turn th...
Page 6: The Hob Top
7 before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top using a soft cloth well wr...
Page 7: Something Not Working?
8 something not working? If the appliance is not working correctly, please carry out the following checks before contacting your local service centre. Symptom ■ there is no spark when lighting the gas ■ the gas ring burns unevenly solution ◆ check that the unit is plugged in and the electrical suppl...
Page 8: Engineer Technical Data
9 overall dimensions width: 680 mm. Depth: 510 mm. Height: 72 mm. Weight: 12 kg. Cut out dimensions width: 560 mm. Depth: 480 mm. Thickness: 30 mm. Instructions for the installer engineer technical data supply connections gas: rc 1/2 inch (1/2 inch male) rear right hand corner electric: 230-v 50hz s...
Page 9: Installation
10 rectangular cut-out size for hob 560 150 min 480 55 min. Fo 2038 dimensions are given in mm. Installation cut out size the dimensions of the cut-out are given in the diagram. A) end of shaft with nut b) washer c) adjustable joint important this appliance must be installed by qualified personnel. ...
Page 10: Building In
11 building in building over a cupboard or drawer if the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. Building over a kitchen unit with door proper arrangements must be taken in de...
Page 11
12 50 50 fo 2039 fo 0199 a carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. From the side edges, as shown in the diagram, taking care that the seals meet without overlappin...
Page 12: Electrical Connections
13 electrical connections any electrical work required to install this appliance should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This appliance must be earthed. The manufacturer declines any liability should these safety measures not ...
Page 13: Commissioning
14 commissioning when the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - turn the gas tap to the max position and ignite. - set the gas tap to the min flame position then turn the control knob from min to max several ti...
Page 14: Servicing
15 a: removal of hob top 1. Remove all control knobs, pan supports, burner caps and burner crowns. 2. Remove 2 screws for each burner. 3. Remove 6 fixing screws from the pan support hinges, and remove the hinges from the hob. 4. Lift hob top at the rear and disengage it from the front locators. B: r...