- DL manuals
- Zanussi
- Hob
- ZGF 782 CTN
- Instruction Booklet
Zanussi ZGF 782 CTN Instruction Booklet - Description of The Hob
Summary of ZGF 782 CTN
Page 1
Gas hob zgf 782 ctn zgf 782 ctx instruction booklet please read this instruction booklet before using the appliance gb ie.
Page 2: Important Safety Information
2 important safety information you must read these warnings carefully before installing or using the hob. If you need assistance, contact our customer care department on 08705 727727 installation z this appliance must be installed and serviced by a competent person as stated in the gas safety (insta...
Page 3: For The User
3 for the user contents for the installer important safety information 2 description of the hob 4 operation 5 maintenance and cleaning 6 something not working? 7 this appliance complies with the following e.E.C. Directives: * 73/23 - 90/683 (low voltagedirective); * 93/68 (general directives); * 89/...
Page 4: Description of The Hob
4 1. Auxiliary burner 2. Semi-rapid burners 3. Ultra-rapid triple-crown burner 4. Rapid burner 5. Control knobs description of the hob 2 1 4 3 2 5.
Page 5: Operation
5 operation hob burners to light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (fig. 1, d) to be heated and the safety device to ...
Page 6: Maintenance and Cleaning
6 maintenance and cleaning before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top u...
Page 7: Something Not Working?
7 something not working? If the hob is not working correctly, please carry out the following checks before contacting your local zanussi service force centre. Symptom there is no spark when lighting the gas the gas ring burns unevenly solution check that the unit is plugged in and the electrical sup...
Page 8: Engineers Technical Data
8 overall dimensions width: 680 mm depth: 510 mm cut out dimensions width: 560 mm depth: 480 mm supply connections gas: r 1/2 inch (1/2 inch male) rear right hand corner electric: 230 v 50 hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. Rear left burner ...
Page 9: Provision For Ventilation
9 fitting the gas hob without a cooker hood above fitting the gas hob with a cooker hood above 700 mm 400 mm 400 mm 100 mm 55 mm 50 mm 50 mm 600 mm 700 mm 400 mm 400 mm 100 mm 55 mm 600 mm 50 mm 50 mm fo 2369* fo 2231* important safety requirements this hob must be installed in accordance with the g...
Page 10: Installation
10 installation important: this hob must be installed by a competent person to the relevant gas standards. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in...
Page 11: Building In
11 f o 2564 fo 2044 3 dimensions are given in mm. Building in building over a cupboard or drawer if the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry...
Page 12: Electrical Connections
12 electrical connections any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This hob must be earthed. The manufacturer declines any liability should these safety measures not be observed....
Page 13: Fault Finding
13 fault finding preliminary electrical systems check a. Earth continuity check - appliance must be electrically disconnected - meter set on Ω (ohms) x 1 scale and adjust zero if necessary. A) test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (ohm),...
Page 14
14 ignition system / gas ignition yes check plug top fuse and replace if necessary check polarity and earth continuity of supply point check earth continuity of appliance ignitor does not spark check fitting of burners check position of the electrode check by pass simmer adjusted light burner manual...
Page 15: Commissioning
15 commissioning when the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - turn the gas tap to the max position and ignite. - set the gas tap to the min flame position then turn the control knob from min to max several ti...
Page 16: Guarantee/customer Service
16 guarantee/customer service standard guarantee conditions we, zanussi-electrolux, undertake that if within 12 months of the date of the purchase this zanussi-electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option...
Page 17: European Guarantee
17 this appliance is guaranteed by electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move w...
Page 18
18.
Page 19
19.
Page 20
Grafiche mdm - forlì 35687-7802 11/06 www.Zanussi-electrolux.Co.Uk.