- DL manuals
- Zanussi
- Hob
- ZGF 782
- Instruction Booklet
Zanussi ZGF 782 Instruction Booklet
Summary of ZGF 782
Page 1
Gas hob model zgf 782 instruction booklet please read this instruction booklet before using the appliance.
Page 2
3 important safety information you must read hese warnings carefully before installing or using the hob. If you need assistance, contact our customer care department on 08705 727727 installation l this hob must be installed by qualified personnel, according to the manufacturers instructions and to ...
Page 3: Contents
4 this appliance complies with the following e.E.C. Directives: * 73/23 - 90/683 (low voltagedirective); * 93/68 (general directives); * 89/336 (electromagnetical compatibility directive); * 90/396 (gas appliances), and subsequent modifications guide to use the instructions the following symbols wil...
Page 4: Description Of The Hob
5 1. Hob top 2. Auxiliary burner 3. Semi-rapid burners 4. Ultra-rapid double-crown burner 5. Rapid burner 6. Ignition pushbutton 7. Control knob for front left burner (auxiliary) 8. Control knob for back left burner (semi-rapid) 9. Control knob for central burner (ultra-rapid) 10. Control knob for b...
Page 5: Operation
6 operation hob burners to light a burner, push the relevant control knob in, turn it anticlockwise to maximum position, and depress the ignition pushbutton marked by a small electric spark symbol. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and t...
Page 6: Maintenance and Cleaning
7 before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top using a soft cloth well wr...
Page 7: Something Not Working?
8 something not working? If the hob is not working correctly, please carry out the following checks before contacting your local zanussi service force centre. Symptom n there is no spark when lighting the gas n the gas ring burns unevenly solution u check that the unit is plugged in and the electric...
Page 8: Peace of Mind For 24 Months
9 zanussi guarantee conditions we, zanussi, undertake that if, within 24 months of the date of the purchase, this zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same free of any char...
Page 9
10 burner rapid semi-rapid auxiliary ultra-rapid (double-crown) (large) (medium) (small) rod pan supports cast iron pan supp. Position max min max min max min max min max min nominal thermal power kw 3.0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 3.5 1.2 nominal flow rate m 3 /h 0.286 0.062 0.190 0.043 0.095 0....
Page 10
11 fitting the gas hob without a cooker hood above fitting the gas hob with a cooker hood above 700 mm 400 mm 400 mm 100 mm 55 mm 50 mm 50 mm 600 mm 700 mm 400 mm 400 mm 100 mm 55 mm 600 mm 50 mm 50 mm fo 2369* fo 2231* important safety requirements this hob must be installed in accordance with the ...
Page 11: Installation
12 rectangular cut-out size for hob a) end of shaft with nut b) washer c) elbow it is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Fo 0814 gas connection conn...
Page 12: Building In
13 on/off switch flex outlet on/off switch flex outlet fo 0763 fo 0764 30 20 min 60 a b fo 1013 1 2 3 50 50 fo 2039 fo 0199 a fitting the hob into the worktop carry out the building in of the hob as follows: put the seals supplied with the hob, on the edges of the cut out: place them exactly on th...
Page 13: Electrical Connections
14 electrical connections any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This hob must be earthed. The manufacturer declines any liability should these safety measures not be observed....
Page 14: Wiring Diagram
15 a. Ignitor switch b. Ignitor unit b l n 0 1 2 3 4 5 6 220/240 a wiring diagram.
Page 15: Fault Finding
16 fault finding preliminary electrical systems check a. Earth continuity check - appliance must be electrically disconnected - meter set on (ohms) x 1 scale and adjust zero if necessary. A) test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 (ohm), che...
Page 16
17 ignition system / gas ignition yes check plug top fuse and replace if necessary check polarity and earth continuity of supply point check earth continuity of appliance ignitor does not spark check fitting of burners check position of the electrode check by pass simmer adjusted light burner manual...
Page 17: Commissioning
18 commissioning when the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - turn the gas tap to the max position and ignite. - set the gas tap to the min flame position then turn the control knob from min to max several ti...
Page 18
19 conversion from natural gas to lpg it is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit. Method ensure that the gas taps are in the 'off' ...
Page 19
35669-7303 12/99 grafiche mdm - forlì.