Summary of ZGF 786 ICW
Page 1
1 gas hobs (zgf 786 icx) (zgf 786 icw) operating and installation manual.
Page 2: English
2 • this appliance has been designed to be operated by adults and children under supervision. Young children must not be allowed to tamper with the controls or play near or with the oven. • this appliance has been designed for cooking edible foodstuff and to be used for domestic non- professional pu...
Page 3: 1. Instruction For The User
3 1. Instruction for the user hob burners control knobs the hob burners control knobs are situated on the hob front panel. The symbols on the knobs mean that : ● there is no gas supply there is maximum gas supply there is minimum gas supply lighting the burners • for easier lighting, proceed before ...
Page 4: 2. Cleaning and Maintenance
4 2. Cleaning and maintenance • disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. General cleaning wash the enamelled components with warm soapy water. Never use abrasive cleaners frequently wash the "caps" and the "crowns" with hot soapy wate...
Page 5
5 fo 2032 fig. 4 fig. 5 fo 2030 only enamelled pan supports can be lifted in this way fo 2292 enamelled pan supports in hobs provided with enamelled pan supports, these can be removed and kept in the right position thanks to special hinges in the back of the hob (see fig. 4 and 5). This solution ena...
Page 6: 5. Technical Data
6 5. Technical data gas burners rating ultra-rapid burner (double crown) 3,4 kw rapid burner (big) 2,9 kw semirapid burner (medium) 1,9 kw auxiliary burner (small) 1,1 kw category ii2hs3b/p setting natural gas g 20 25 mbar gas connection g 1/2" electric supply 230 v 50 hz hob recess dimensions lengt...
Page 7
7 6. Instruction for the installer ● the following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. ● the side walls of the unit in which the hob is going to be installed, must not exceed the height of the working ...
Page 8: 7. Electrical Connection
8 the appliance is designed to be connected to 230 v monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the ratin...
Page 9
9 adjustment of minimum level to adjust the minimum level of the burners, proceed as follows: • light the burner. • turn the knob on the minimum position. • remove the knob. • with a thin screwdriver, adjust the by-pass screw (see fig. 11). If changing from natural gas to lpg, completely tighten clo...
Page 10: 9. Building In
10 9. Building in a = auxiliary burner sr = semirapid burner r = rapid burner ur = ultra-rapid burner (double crown) these hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in fig. 12. 510 680 a sr sr r ur hobs with enamelled pan sup...
Page 11
11 fitting the lid we recommend the lid hinge block are fitted before installing the hob into the worktop. To install the lid onto the hob, proceed as follows: a. Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (fig. 13) b. Fit the lid hing...
Page 12
12 installation and assembly these hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in fig. 16. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the ...
Page 13
13 480 30 591 380 140 360 cm 2 50 cm 2 120 cm 2 180 cm 2 30 20 min 60 a b possibilities for insertion kitchen unit with door proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recomm...