Zanussi ZGF783 ITXC Instruction Book

Other manuals for ZGF783 ITXC: Instruction Booklet

Summary of ZGF783 ITXC

  • Page 1

    32 • this appliance has been designed to be operated by adults and children under supervision. Young children must not be allowed to tamper with the controls or play near or with the oven. • this appliance has been designed for cooking edible foodstuff and to be used for domestic non- professional p...

  • Page 2: 1. Instruction For The User

    33 1. Instruction for the user hob burners control knobs the hob burners control knobs are situated on the hob front panel. The symbols on the knobs mean that : l there is no gas supply there is maximum gas supply there is minimum gas supply lighting the burners • for easier lighting, proceed before...

  • Page 3: 2. Cleaning and Maintenance

    34 2. Cleaning and maintenance • disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Wash the enamelled components with warm soapy water. Never use abrasive cleaners frequently wash the "caps" and the "crowns" with hot soapy water, carefully tak...

  • Page 4: 3. Technical Data

    35 3. Technical data gas burners rating triple crown burner 4,0 kw rapid burner (big) 3,0 kw (g20) - 2,8 kw (g30-31) auxiliary burner (small) 1,0 kw semirapid burner (medium) 2,0 kw class 3 appliance category ii 2e+3+ setting natural gas g20/ g25 - 20/25 mbar gas connection g 1/2" electric supply 23...

  • Page 5

    36 4. Instruction for the installer l the following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The regulation to be applied for this type of installation is nbn d 5i.003 : "installations functioning with comb...

  • Page 6: 5. Electrical Connection

    37 the appliance is designed to be connected to 230 v monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rati...

  • Page 7

    38 injectors replacement • remove the pan supports. • remove the burner's caps and crowns. • with a socket spanner 7 unscrew and remove the injectors (fig. 7), and replace them with the ones required for the type of gas in use (see table 2). • reassemble the parts, following the same procedure backw...

  • Page 8: 7.  Building In

    39 fitting the lid we recommend the lid hinge block are fitted before installing the hob into the worktop. To install the lid onto the hob, proceed as follows: a. Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (fig. 10) b. Fit the lid hing...

  • Page 9

    40 installation and assembly these hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in fig. 13. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the ...

  • Page 10

    41 480 30 591 380 140 360 cm 2 50 cm 2 120 cm 2 180 cm 2 30 20 min 60 a b possibilities for insertion kitchen unit with door proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recomm...

  • Page 11

    42 our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result. This declaration of g...

  • Page 12

    43.

  • Page 13

    35668-8651 11/02 grafiche mdm - forlì from the electrolux group. The world’s no.1 choice. The electrolux group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million electrolux group products (such as refrigerators, cookers, washing machines...