DL manuals
Zanussi
Hob
ZGL 62
Instruction Booklet

Zanussi ZGL 62 Instruction Booklet - Electrical Connections

Other manuals for ZGL 62: Instruction Booklet

Manual is about: Zanussi Cooktop User Manual

Page of 16

Download

Print this page

Bookmark us

Electrical connections

Any electrical work required to install this hob

should be carried out by a qualified electrician or

competent person, in accordance with the current

regulations.

THIS HOB MUST BE EARTHED.

The manufacturer declines any liability should these

safety measures not be observed.

This hob is designed to be connected to a 230 V 50 Hz

AC electrical supply.

Before switching on, make sure the electricity supply

voltage is the same as that indicated on the hob rating

plate. The rating plate is located on the bottom of the

hob. A copy is attached on the back cover of this book.

The hob is supplied with a 3 core flexible supply cable

incorporating a 3amp plug fitted. In the event of having to

change the fuse, a 3amp ASTA approved (BS 1362) fuse

must be used.

Should the plug need to be replaced for any reason, the

wires in the mains lead are coloured in accordance with

the following code:

Green and Yellow - Earth

Blue

- Neutral

Brown

- Live

— Connect the green and yellow (earth) wire to

the terminal in the plug which is marked with

the letter 'E' or the earth symbol

or coloured

green and yellow.

— Connect the blue (neutral) wire to the terminal

in the plug which is marked with the letter 'N'

or coloured black.

— Connect the brown (live) wire to the terminal in

the plug which is marked with the letter 'L' or

coloured red.

Upon completion there must be no cut, or stray strands

of wire present and the cable clamp must be secure over

the outer sheath.

A cut off plug inserted into a 13 amp socket is

a serious safety (shock) hazard. Ensure that

the cut off plug is disposed of safely.

Permanent Connection

In the case of a permanent connection, it is necessary

that you install a double pole switch between the hob

and the electricity supply (mains), with a minimum gap

of 3 mm. between the switch contacts and of a type

suitable for the required load in compliance with the

current electric regulations.

The switch must not break the yellow and green earth

cable at any point.

Ensure that the hob supply cable does not

come into contact with surfaces with

temperatures higher than 50 deg. C.

FO 0390

)

« ‹ Prev 9 10 11 12 13 14 15 Next › »

Summary of ZGL 62

Page 1
Gas hob zgl 62 instruction booklet please read this instruction booklet before using the appliance gb.
Page 2: Important Safety Information
2 guide to use the instructions the following symbols will be found in the text to guide you throughout the instructions: safety instructions step by step instructions for an operation hints and tips environmental information important safety information you must read these warnings carefully before...
Page 3: Description of The Hob
3 description of the hob this appliance complies with the following e.E.C. Directives: * 73/23 - 90/683 (low voltagedirective); * 93/68 (general directives); * 89/336 (electromagnetical compatibility directive); * 90/396 (gas appliances), and subsequent modifications for the user contents for the in...
Page 4: Operation
4 operation a - burner cap b - burner crown c - ignition electrode burner minimum maximum diameter diameter large (rapid) 180 mm 260 mm medium (semi-rapid) 120 mm 220 mm small (auxiliary) 80 mm 160 mm hob burners to light a burner: z turn the relevant control knob anticlockwise to the maximum positi...
Page 5: The Hob Top
5 before any maintenance or cleaning can be carried out, you must disconnect the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The hob top regularly wipe over the hob top using a soft cloth well wr...
Page 6: Something Not Working?
6 something not working? If the hob is not working correctly, please carry out the following checks before contacting your local zanussi service force centre. Important: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will b...
Page 7: Zanussi Guarantee Conditions
7 zanussi guarantee conditions we, zanussi, undertake that if, within 24 months of the date of the purchase, this zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same free of any char...
Page 8: Engineers Technical Data
8 rear left burner (semi rapid) heat input 2.0 kw (6824 btu/hr) front left burner (rapid) heat input 3.0 kw natural gas (10236 btu/hr) 2.8 kw l.P.G. (9554 btu/hr) rear right burner (semi rapid) heat input 2.0 kw (6824 btu/hr) front right burner (auxiliary) heat input 1.0 kw (3412 btu/hr) instruction...
Page 9: Provision For Ventilation
9 important safety requirements 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm i clearances required when fitting the hob without a cooker hood above clearances required when fitting the hob with a cooker hood above fo 0813 fo 0812 700 mm this hob ...
Page 10: Gas Connection
10 a) end of shaft with nut b) washer c) elbow fo 0814 gas connection connection to the gas supply should be with either rigid or semi-rigid pipe, i.E. Steel or copper. The connection should be suitable for connecting to rc 1/2 (1/2 bsp male thread). When the final connection has been made, it is es...
Page 11: Building In
11 fo 0763 fo 0764 fo 1013 2 3 fo 0199 a fitting the hob into the worktop ) carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is ...
Page 12: Electrical Connections
12 electrical connections any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. This hob must be earthed. The manufacturer declines any liability should these safety measures not be observed....
Page 13: Fault Finding
13 fault finding preliminary electrical systems check a. Earth continuity check - appliance must be electrically disconnected - meter set on Ω (ohms) x 1 scale and adjust zero if necessary. A) test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (ohm),...
Page 14
14 ignition system / gas ignition yes check plug top fuse and replace if necessary check polarity and earth continuity of supply point check earth continuity of appliance ignitor does not spark check fitting of burners check position of the electrode check by pass simmer light burner manually check ...
Page 15: To Adjust The Gas Rate
15 conversion from natural gas to lpg important the replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct inject...
Page 16
Grafiche mdm - forlì 35675-2602 01/05 customer care zanussi 55-77 high street slough berkshire, sl1 1dz tel: 08705 727727 long mile road dublin 12 republic of ireland tel: + 353 (0) 1 4090751 © electrolux plc 2003 from the electrolux group. The world’s no.1 choice. The electrolux group is the world’...