Summary of ZXS 646 IT
Page 1
1 built-in hob zxs 646 it instruction booklet ua si hr.
Page 2: About Installation, Cleaning
2 about installation, cleaning and maintenance • it is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. • disconnect the appliance from the electrical supply, before carrying out any cle...
Page 3: Hob Burners Control Knobs
3 once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Hob burners control knobs the hob burners control knobs are situated on the hob right hand side. The symbols on the knobs mean that: there is no gas supply there is maximum gas su...
Page 4: Using The Hob Correctly
4 burner minimum maximum diameter diameter medium (semirapid) 120 mm. 220 mm. Small (auxiliary) 80 mm. 160 mm. Using the hob correctly to ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will...
Page 5
5 before the first use of the appliance before using the appliance remove all packaging, including the advertising labels and any protective film. When using the hob for the first time: 1) place on all the plates a pan filled with some water; 2) switch the plates on for about 10 minutes at “maximum”...
Page 6: Cleaning and Maintenance
6 cleaning and maintenance disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. General cleaning wash the enamelled components with warm soapy water. Never use abrasive cleaners frequently wash the "caps" and the "crowns" with hot soapy water, ca...
Page 7: Gas Burners Rating
7 gas burners rating auxiliary burner 1 kw semirapid burner 2 kw appliance class 3 category ii 2h3b/p setting lpg g30/g31 30/37 mbar gas connection g 1/2" the following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in for...
Page 8: Metal Pipes
8 fo 0067 fig. 4 choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with ...
Page 9: Electrical Connection
9 the following instructions about installation must be carried out by qualified personnel in compliance with the regulation in force. The appliance is designed to be connected to 230 v monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in fo...
Page 10: Injectors Replacement
10 injectors replacement • remove the pan supports. • remove the burner's caps and crowns. • with a socket spanner 7 unscrew and remove the injectors (fig. 7), and replace them with the ones required for the type of gas in use (see table 2). • reassemble the parts, following the same procedu- re bac...
Page 11: Building In
11 these hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in the relevant diagram. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the ho...
Page 12: Kitchen Unit With Door
12 a) removable panel b) space possibly useful for connections fig. 12 fig. 13 fig. 15 fig. 16 fo 1013 fo 0947 fo 0198 kitchen unit with door proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is ope...
Page 13: European Guarantee
13 european guarantee this appliance is guaranteed by electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance gu...
Page 14
14.
Page 15
15.
Page 16
35675-9104 r.B 05/09.