1. DL manuals
  2. ZBA
  3. Barcode Reader
  4. Z-3080
  5. User Manual

ZBA Z-3080 User Manual

Manual is about: CCD Barcode Scanner

Summary of Z-3080

  • Page 1

    Z-3080 ccd barcode scanner multi-interface user’s manual zba inc 94 old camplain road hillsborough nj 08844 phone: 908-359-2070 fax: 908-359-1272 web: http://www.Zbausa.Com/.

  • Page 2: Notice

    Notice the issuer of this manual has made every effort to provide accurate information contained in this manual. The issuer shall not be held liable for any technical and editorial omissions or errors made herein; nor for incidental consequential damages resulting from the furnishing, performance or...

  • Page 3: Keyboard Wedge

    Installation keyboard wedge 1. Turn off the pc 2. Disconnect the keyboard cable from the pc. 3. Connect the keyboard cable to the scanner and connect the scanner cable to the pc 4. Turn the terminal/computer power on. 5. You are ready use the scanner rs-232 1. Turn off the pc. 2. Connect the scanner...

  • Page 4

    Table of contents introduction......................................................... 1 default parameters ............................................. 2 program procedure............................................. 5 system setting ................................................... 6 general c...

  • Page 5

    Chinese post code parameters setting..............32 upc/ ean/ jan parameters setting ..................33 coda bar/ monarch parameters setting..............37 code 128 parameters setting ............................37 matrix 25 parameters setting ..........................38 msi/plessy parameters s...

  • Page 6

    3. Default parameters this table gives the default settings of all the programmable parameters. The default settings will be restored whenever the "reset" programming label is scanned and the laser scanner is in programming mode. Default values of operating parameters function default values scannin...

  • Page 7

    Default values of decoding parameters function code default value code 39 enable itf 2 of 5 enable chinese post code disable upc/ean/jan enable coda bar enable reading codes ¡ ° msi disable selection code 128 enable code 93 enable ¡ ° itat disable ¡ ° ean-128 disable ¡ ° matrix 25 disable ¡ ° italia...

  • Page 8: System Setting

    System setting 6 start of configuration reset Ÿ the reading of the "reset” label turns all the parameters back to default values. Ÿ when you intend to turn your scanner back to default parameter, please scans the "start of configuration" label first, then scan "reset" label abort rs-232c pc/at usb w...

  • Page 9: General

    General configuration 8 start of configuration scanning mode selection (for laser scanner) for series laser scanners, there are 3 scanning modes to suit your application requirements. Trigger mode pulse mode the scanner becomes inactive as soon as the data is transmitted. It must be triggered to bec...

  • Page 10

    Start of configuration data redundant check the option allows you to set decoder data redundant check. Enable disable inter-message delay these series of scanners allow you to add a delay between two consecutive messages. This delay will be added before each data transmission. None 100 msec 500 msec...

  • Page 11

    Start of configuration send command in block mode communication you can use this option to set your own “sen d” command used in block mode communication. Enable disable store set good read beeper tone selection you can use this option to set frequency and / or duration of the buzzer after successful...

  • Page 12: Interface

    Interface configuration 14 start of configuration 1. Rs-232c serial communication parameters setting the rs-232c scanner supports four handshaking protocols. With these options of communication protocol, you can tailor the scanner to meet the requirement of most systems handshaking protocol none rts...

  • Page 13

    Start of configuration ack/nak response time setting (cont’d) 3 sec 1 sec 5 sec baud rate 19200 9600 4800 2400 1200 600 16 data bit 7 8 stop bit 1 2 parity even odd mark space none end of configuration 17.

  • Page 14

    Start of configuration message terminator (for rs-232c type only) none cr/lf cr lf h tab stx/etx eot 18 2. Keyboard emulation parameters setting keyboard type selection the keyboard emulation scanners can emulate a number of personal computers keyboard and a number of terminal keyboard. Keyboard emu...

  • Page 15

    Start of configuration keyboard type selection (cont’d) nec 9801 ibm 3196 terminal apple mac ii(¡ ° ) ibm 3477/3472 terminal ps2/30/56 ibm 3477 terminal (without break code) nec 5200(¡ ° ) note: the configuration of the items with asterisk (¡ ° ) is optional. 20 keyboard language selection usa uk fr...

  • Page 16

    Message terminator (for keyboard wedge use) none return /enter hor. Tab execute keyboard type selection scan code mode alt mode break code on/ off setting (for ibm terminals 31xx, 34xx, 37xx use) to select the interface for these ibm terminals, read the correct key transmission code. On off 22 funct...

  • Page 17

    Start of configuration 00h~1fh ascii code defined alt-mode code crtl+code 3. Wand emulation parameters setting emulation speed selection low medium normal high higher 24 emulation data output selection the decoded data output logic level can be set to befit the external decoder. Black = high black =...

  • Page 18: The Symbologies

    Start of configuration 4. Usb interface parameters setting the usb mode is effectively a keyboard emulator that works with hosts that usb-compatible operating system and usb ports. Usb compatible operating systems are windows 98, windows nt 5.0 and later, no additional software is needed since the u...

  • Page 19

    Start of configuration reading code selection code 39 enable code 39 disable coda bar enable coda bar disable upc/ ean/ jan enable upc/ ean/ jan disable itf 2 of 5 enable itf 2 of 5 disable chinese post code enable chinese post code disable code 128 enable 28 code 128 disable msi enable msi disable ...

  • Page 20

    Start of configuration reading code selection (cont’d) italian pharmacy enable italian pharmacy disable code 39 parameters setting character set standard code 39 full ascii code 39 start/stop character transmission yes no check digit calculate and transmit calculate but not transmit 30 no concatenat...

  • Page 21

    Start of configuration check digit no calculate and transmit calculate but not transmit chinese post code parameters setting length max min set scan:. Start of configuration min 0 4 set max 0 8 set end of configuration 32 check digit no calculate and transmit calculate but not transmit upc/ean/jan p...

  • Page 22

    Start of configuration upc/ean/jan parameters setting (cont’d) ean-13 ean-8 addendum no 5 characters 2 characters 2 or 5 characters force upc-e to upc-a format yes no 34 force upc-a to ean-13 format yes no transmit upc-a leading character yes no transmit upc-a check digit yes no transmit upc-e leadi...

  • Page 23

    Start of configuration transmit upc-e check digit yes no transmit ean-13 check digit yes no transmit ean-8 check digit yes no 36 codabar/ monarch parameters setting start/ stop character transmission no a, b, c, d dc1~dc4 a/ t, b/ n, c/ *, d/ e concatenation enable disable code 128 parameters settin...

  • Page 24

    Start of configuration code 128 parameters setting (cont’d) check digit no calculate but not transmit calculate and transmit ucc/ean128 parameters setting the character fnc1 can be transmitted or not using these codes. Fnc1 character transmitted fnc1 not transmitted matrix 25 parameters setting exam...

  • Page 25

    Start of configuration msi/plessy parameters setting (cont’d) plessy code setting calculated and transmitted calculate but not transmitted check dight no calculate and transmit calculate but not transmit italian pharmacy parameters setting transmit "a" character yes no 40 barcode length setting code...

  • Page 26: Data Editing

    Start of configuration isbn/ issn conversion the function convents the upc/ean codes appearing on books and magazine not isbn/issn format. Active isbn/ issn inactive isbn/ issn end of configuration 42 data editing 43.

  • Page 27

    Start of configuration header and trailer this option allows you to append a header and/or a trailer to every message transmitted via the serial ports or the keyboard port. There is no restriction in selecting header or trailer characters as far as the sum of the lengths of header and trailer is not...

  • Page 28

    Start of configuration barcode identifier code setting (cont’d) coda bar code 39 code 128 code 93 msi matrix 25 set 46 truncate header/trailer character (version az1.24, dz1.05, ac1.01, dz1.05,pl1.39 or higher is required) you can truncate a number header or trailer for a symbology. When you do, the...

  • Page 29: Appendixes

    Appendixes 48 appendix a code 39 full ascii code table ascii code 39 valeur hexa. Ascii code 39 valeur hexa. Nul %u 00 % /e 25 soh $a 01 & /f 26 stx $b 02 ' /g 27 etx $c 03 ( /h 28 eot $d 04 ) /i 29 enq $e 05 * /j 2a ack $f 06 + /k 2b bel $g 07 , /l 2c bs $h 08 - - 2d ht $i 09 . . 2e lf $j 0a / / 2f...

  • Page 30

    Appendix a code 39 full ascii code table ascii code 39 valeur hexa. Ascii code 39 valeur hexa. J j 4a e +e 65 k k 4b f +f 66 l l 4c g +g 67 m m 4d h +h 68 n n 4e i +i 69 o o 4f j +j 6a p p 50 k +k 6b q q 51 l +l 6c r r 52 m +m 6d s s 53 n +n 6e t t 54 o +o 6f u u 55 p +p 70 v v 56 q +q 71 w w 57 r +...

  • Page 31

    Appendix b code 39 full ascii barcode table start of configuration nul enq (up) soh (ins) ack (down) stx (del) bel (left) etx (home) bs (backspace) eot (end) ht (tab) 52 appendix b code 39 full ascii barcode table lf (enter)(num) dle 5 (num) vt (right) dc1 (f1) ff (pgup) dc2 (f2) cr (enter) dc3 (f3)...

  • Page 32

    Appendix b code 39 full ascii barcode table start of configuration syn (f6) gs (esc) etb (f7) rs ctl (l) can (f8) us alt (l) em (f9) sp sub (f10) ! Esc (f11) " fs (f12) # 54 appendix b code 39 full ascii barcode table $ + % , & - ' . ( / ) 0 * 1 end of configuration 55.

  • Page 33

    Appendix b code 39 full ascii barcode table start of configuration 2 : 3 ; 4 5 = 6 > 7 ? 8 @ 9 a 56 appendix b code 39 full ascii barcode table b i c j d k e l f m g n h o end of configuration 57.

  • Page 34

    Appendix b code 39 full ascii barcode table start of configuration p w q x r y s z t [ u \ v ] 58 appendix b code 39 full ascii barcode table ^ e _ f ` g a h b i c j d k end of configuration 59.

  • Page 36

    Appendix c barcode samples code 39 c o d e 3 9 code 128 c o d e 1 2 8 interleaved 2 of 5 1 2 3 4 5 6 7 8 9 0 coda bar(nw-7) a $ 9 9 . 9 5 a upc a 0 4 4 2 5 2 3 0 2 4 5 1 ean-13 4 7 1 1 2 3 4 5 6 7 8 9 9 62 appendix d quick settings 1. Quick settings for keyboard wedge mode program reset pc/at end 2....