Summary of ZB-8110
Page 1
Zb-8150/zb-8110/zb-8210 ccd barcode scanner user’s manual zba inc 94 old camplain road hillsborough nj 08844 phone: 908-359-2070 fax: 908-359-1272 web: http://www.Zbausa.Com/ 1.
Page 2
Installation: keyboard wedge 1) turn off the pc 2) disconnect the keyboard cable from the pc. 3) connect the keyboard cable to the scanner and connect the scanner cable to the pc 4) turn the terminal/computer power on. 5) you are ready use the scanner rs-232 1) turn off the pc. 2) connect the scanne...
Page 3
Default setting for each barcode shown as below: read enable code type 8110 8150/8210 checksum verification enable checksum transmission enable code id upc-a v v v v a upc-e v v v v e ean-13 v v v v f ean-8 v v v v ff code-39 v v ＊ interleaved 2 of 5 v v v i industrial 2 of 5 - - i matrix 2 of 5 b c...
Page 4
Zba zb- 8110 / 8150 - 1d barcode scanner specification mode l 8110 mode l 8150 operational light source 660 nm visible red led optical system 2048 pixel ccd (charge-coupled device) depth of scan field 0-80 mm (code 39, pcs=90%, 20mils) 0-250 mm (code 39, pcs=90%, 20mils) scanning width 80 mm 120 mm ...
Page 5
Weight 155 g (cable not included) 160 g (cable not included) cable – k/b wedge straight 2.0 m cable – universal type straight 2.3 m connector type rj-45 phone jack connector case material abs plastic cushion material rubber electrical input voltage 5 vdc ± 0.25v power - operating 380 mw 1275 mw powe...
Page 6
Programming programming method manual (reading special barcode) dos command through rs-232, windows configuration program program upgrade enabled by built-in flash memory programmable characteristics code type selection, check digit selection decoding option decoding option transmitted character del...
Page 7
Programming the 8110/8150/8210 to program the 8110/8150/8210, you must scan a series of programming barcode in the correct order. Fold out the back cover of this manual. You will see a table of alphanumeric barcodes, which are used to program the various options presented. To program each option, yo...
Page 8
Option bar code option alphanumeric entry interface selection keyboard wedge rs-232 wand emulation usb keyboard/rs-232 auto detection reserved 00＊ 01 02 03 04 05 back fold out finish barcode exit barcode option barcode program barcode exit program 8.
Page 9
Interface selection this decoder build-in scanner comes in one model and supports interfaces such as keyboard wedge, rs232 serial wedge, wand emulation, and the latest usb interface. In most of the cases, simply selecting an appropriate cable with a device code will work for a specific interface. In...
Page 10
Keyboard wedge as a keyboard interface, the scanner supports most of the popular pcs and ibm terminals. The installation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard type: select keyboard type connector of your host computer. Scanner must be selected ...
Page 11
Keyboard wedge keyboard layout: the selecting of keyboard layout supports many country languages other than usa keyboard layout. First you need to confirm country language that you desire. In dos, using command “keyb” to select the desirable keyboard layout or in windows entry “control” then pops “k...
Page 12
Keyboard layout usa belgium danish france germany italian portuguese spanish swedish switzerland uk latin american 00 ＊ 01 02 03 04 05 06 07 08 09 10 11 keyboard speed 0-8 0 : high clock rate 8 : low clock rate 00-08 01 ＊ function key disable enable 00 01 ＊ numeric key alphabetic key numeric keypad ...
Page 13
Keyboard wedge caps lock: by selecting caps lock or no caps lock, scanner can get caps lock status. Power-on simulation: all of the pcs check the keyboard status during power-on selftest. It is recommended to enable function if you are working without keyboard installation. It simulates keyboard tim...
Page 14
Program option bar code option alphanumeric entry caps lock caps lock”on” caps lock”off” 00 01 ＊ power-on simulation disable enable 00 ＊ 01 inter-character delay 00-99 msec 00-99 02 ＊ block transmission delay 00-99 10 msec 00-99 10 ＊ exit 14.
Page 15
Rs-232 cts: clear to send (hardware signal) rts: request to send (hardware signal) xon: transmit on (ascii code 11 16 ) xoff: transmit off (ascii code13 16 ) flow control: none-the communication only uses txd and rxd signals without regard for any hardware or software handshaking protocol. Rts/cts-i...
Page 16
Program option bar code option alphanumeric entry flow control none rts/cts xon/xoff ack/nak 00 ＊ 01 02 03 inter-character delay 00-99 (msec) 00-99 00 ＊ block transmission delay 00-99 (10 msec) 00-99 00 ＊ response delay 00-99 (100 msec) 00-99 20 ＊ exit 16.
Page 17
Program option bar code option alphanumeric entry baud rate 300 bps 600 bps 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 38400 bps 00 01 02 03 04 05 ＊ 06 07 parity none odd even 00 ＊ 01 02 data bit 8 bits 7 bits 00 ＊ 01 stop bit one bit two bits 00 ＊ 01 exit 17.
Page 18
Wand emulation bar/space polarity: high/low- black will be transmitted as a high voltage level (+5) and space as low level (0v). Low/high- black will be transmitted as a low voltage level (0v) and space as high level (+5). Initial polarity: you must make sure what is initial polarity of your wand de...
Page 19
Wand emulation output speed: this setting is same as serial transmission baud rate, and it must be approbated your wand decode resolution. The unit of speed is a width of minimum narrow bar. Margin delay: it is a timer of zone like space zone of barcode label margin. The width of margin time will be...
Page 20
Reserved 00 ＊ reserved 00 ＊ margin delay 00-99 (10 pixel) 00-99 15 ＊ transmit delay 00-99 (10 msec) 00-99 30 ＊ exit 20
Page 21
Scan scanning mode: good-read off-the trigger button must be pressed to activate scanning. The light source of scanner stops scanning when there is a successful reading or no code is decoded after the stand-by duration elapsed. Momentary-the trigger button acts as a switch. Press button to activate ...
Page 22
Program option bar code option alphanumeric entry scanning mode good-read off momentary alternate timeout off continue 00 01 ＊ 02 03 04 stand-by duration 01-99 (second) 00-99 10 ＊ same barcode delay time 01-99 (10 msec) 01-99 50 ＊ double confirm 00-99 (00: no double confirm) 00-09 00 ＊ exit 22.
Page 23
Scan multi field scan: the scanner can be read many sets of barcode data on the same scanning line at the same time, even if they are different kinds of barcode symbology. Global min./max. Code length: global minimum and maximum length can be set to qualify data entry. The length is defined as the a...
Page 24
Multi field scan disable enable 00 ＊ 01 global min. Code length 00-63 00-63 04 ＊ global max.Code length 00-63 04-63 63 ＊ inverted image scan disable enable 00 ＊ 01 cts trigger disable enable 00 ＊ 01 position indication disable 30 second 60 second 90 second 120 second 150 second 180 second continue 0...
Page 25
Indication power on alert: after power-on the scanner it will generate an alert signal to indicate a successful self-test. Led indication: after each successful reading, the led above the scanner will light up to indicate a good barcode reading. Buzzer indication: after each successful reading, the ...
Page 26
Program option bar code option alphanumeric entry power on alert disable enable 00 01 ＊ led indication disable enable 00 01 ＊ buzzer indication disable enable 00 01 ＊ beep loudness 00-07 00-07 07 ＊ beep tone freq. 00-99 (100hz) 00-99 26 ＊ beep tone duration 00-99 (10 msec) 00-99 10 ＊ exit 26.
Page 27
Upca read: format leading zero data digits (11 digits) check digit check-sum transmission: by setting enable, checks sum will be transmitted. Truncate leading/ending: the leading or ending digits of barcode data characters can be truncated when these values are set to non-zero. It will beep instead ...
Page 28
Check-sum verification disable enable 00 01 ＊ check-sum transmission disable enable 00 01 ＊ max.Code length 00-64 00-64 64 ＊ min.Code length 00-64 00-64 01 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44...
Page 29
Upca supplement digits: the supplement digits barcode is the supplemental 2 or 5 characters for wpc code. Format leading zero data digits (11 digits) check digit supplement digits 2 or 5 or ucc / ean 128 truncate leading zero: the leading “0” digits of upca data characters can be truncated when the ...
Page 30
Upce read: format leading zero data digits (6 digits) check digits check-sum verification: the checksum of ean-13 is optional and made as the sum of the numerical value of the data digits. Check-sum transmission: by setting enable, checks sum will be transmitted. Program option bar code option alpha...
Page 31
Upce truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group selection of upca. Supplement digits: format leading zero data digits (6 digits) check digit supplement digits 2 or 5 or ucc/e...
Page 32
Truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ supplement digits none 2 digits 5 digits ucc/ean 128 auto detection 00 ＊ 01 02 03 04 truncate leading zero disable enable 00 ＊ 01 expansion disable enable 00 ＊ 01 exit 32.
Page 33
Ean-13 read: format data digits (12 digits) check digits check-sum verification: the checksum of ean-13 is optional and made as the sum of the numerical value of the data digits. Check-sum transmission: by setting enable, checks sum will be transmitted. Max./min. Code length: each symbology has own ...
Page 34
Check-sum verification disable enable 00 01 ＊ check-sum transmission disable enable 00 01 ＊ max.Code length 00-64 00-64 64 ＊ min.Code length 00-64 00-64 01 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ exit 34.
Page 35
Ean-13 code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group selection of upca. Supplement digits: format data digits (12 digits) check digits supplement digits 2 or 5 or ucc / ean 128 isbn/issn: the isbn (international standard book number) and issn (...
Page 36
Program option bar code option alphanumeric entry code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ supplement digits none 2 digits 5 digits ucc/ean 128 auto detection 00 ＊ 01 02 03 04 isbn/issn conversion disable enable 00 ＊ 01 exit 36.
Page 37
Ean-8 read: format data digits (7 digits) check digits check-sum verification: the checksum of ean-8 is optional and made as the sum of the numerical value of the data digits. Check-sum transmission: by setting enable, checks sum will be transmitted. Max./min. Code length: refer to max./min. Code le...
Page 38
Check-sum transmission disable enable 00 01 ＊ max.Code length 00-64 00-64 64 ＊ min.Code length 00-64 00-64 01 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting two characters 00-ffh ascii code 00-ffh, 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 38.
Page 39
Ean-8 supplement digits: format data digits (7 digits) check digits supplement digits 2 or 5 or ucc/ean 128 truncate leading zero: refer to truncate leading zero of upce. Expansion: refer to expansion of upce. Program option bar code option alphanumeric entry supplement digits none 2 digits 5 digits...
Page 40
Code 39 read: format start “ ★” data digits ( variable) checksum (optional) end “ ★” check-sum verification: the checksum of code-39 is optional and made as the sum module 43 of the numerical value of the data digits. Check-sum transmission: by setting enable, checksum and will be transmitted. Optio...
Page 41
Code 39 max./min. Code length: each symbology has own max./min. Code length. They can be set to qualify data entry. If their max./min. Code length is zero, the global min./max. Code length is in effect. The length is defined as to the actual barcode data length to be sent. Label with length exceeds ...
Page 42
Max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ > insert group selection 00-44 00-44 00 ＊ format standard full ascii 00 ＊ 01 exit 42.
Page 43
Code 39 append: this function allows several symbols to be concatenates and be treat as one single data entry. The scanner will not transmit the embedded appending code (space for code-39). If enable and other symbols were read again with the appended code, then codes will be transmitted without cod...
Page 44
Interleaved 2 of 5 read: format data digits (variable) checksum (optional) check-sum verification: the checksum is made as the sum module 10 of the numerical values of all data digits. Check-sum transmission: by setting enable, checksum and will be transmitted. Program option bar code option alphanu...
Page 45
Interleaved 2 of 5 max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group selection of upca. Program option bar code opt...
Page 46
Code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 46.
Page 47
Industrial 2 of 5 read: format data digits (variable) checksum (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinserti...
Page 48
Truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 48.
Page 49
Matrix 2 of 5 eur read: format data digits (variable) checksum (optional) checksum verification: the checksum is made as the sum module 10 of the numerical values of all data digits. Checksum transmission: by setting enable, checksum and will be transmitted. Max./min. Code length: refer to max./min....
Page 50
Checksum transmission disable enable 00 ＊ 01 max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00- 44 00 ＊ exit 50
Page 51
Codabar read: format start data digits (variable) checksum (optional) end checksum verification: the checksum is made as the sum module 16 of the numerical values of all data digits. Checksum transmission: by setting enable, checksum and will be transmitted. Max./min. Code length: refer to max./min....
Page 52
Checksum transmission disable enable 00 ＊ 01 max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ exit 52.
Page 53
Codabar insertion group selection: refer toinsertion group selection of upca. Start/end type: the codabar has four pairs of start/end pattern; you may select one pair to match your application. Start/end transmission: refer to start/end transmission of code 39. Program option bar code option alphanu...
Page 54
Code-128 read: format data digits (variable) checksum (optional) checksum verification: the checksum is made as the sum module 103 of all data digits. Checksum transmission: by setting enable, checksum and will be transmitted. Program option bar code option alphanumeric entry read disable enable 00 ...
Page 55
Code-128 max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group selection of upca. Format: the code-128 can be translate...
Page 56
Truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ format standard ucc/ean-128 00 ＊ 01 append disable enable 00 ＊ 01 ucc/ean-128 id setting 00-ffh ascii code 00-ffh ＊ field separator code 00-ffh ascii co...
Page 57
Code-93 read: format data digits (variable) checksum1 (optional) checksum2 (optional) checksum verification: the checksum is made as the sum module 47 of the numerical values of all data digits. Checksum transmission: by setting enable, checksum and will be transmitted. Max./min. Code length: refer ...
Page 58
Checksum transmission disable enable 00 ＊ 01 max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 58.
Page 59
Code-11 read: format data digits (variable) checksum1 (optional) checksum2 (optional) checksum verification: the checksum is presented as the sum module 11 of all data digits. Checksum transmission: by setting enable, checksum1 and checksum2 will be transmitted upon your selected checksum verificati...
Page 60
Checksum transmission disable enable 00 ＊ 01 max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 60
Page 61
Msi/plessey read: format data digits (variable) checksum1 (optional) checksum2 (optional) checksum verification: the msi/plessey has one or two optional checksum digits. The checksum is presented 3 kinds of method mod10, mod10/10 and mod 11/10. The checksum1 and checksum2 will be calculated as the s...
Page 62
Checksum transmission disable enable 00 ＊ 01 max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 62.
Page 63
Uk/plessey read: format data digits (variable) checksum1+2 (optional) checksum verification: the uk/plessey has one or two optional checksum digits. The checksum1 and checksum2 will be calculated as the sum module 10 or 11 of the data digits. Checksum transmission: by setting enable, checksum will b...
Page 64
Checksum transmission disable enable 00 ＊ 01 max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 64.
Page 65
Telepen read: iata (international air transport association). Checksum verification: the checksum is presented as the sum module 10 or 11 of the data digits. Checksum transmission: by setting enable, checksum will be transmitted. Max./min. Code length: refer to max./min. Code length of code-39. Trun...
Page 66
Max. Code length 00-64 00-64 00 ＊ min. Code length 00-64 00-64 00 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ format numeric only full ascii only 00 ＊ 01 exit 66.
Page 67
Standard 2 of 5 read: format data digits (variable) checksum1 (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertio...
Page 68
Truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ exit 68.
Page 69
Rss-14 read: format data digits (variable) checksum1 (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group s...
Page 70
Truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ ucc/ean128 emulation disable enable 00 ＊ 01 exit 70
Page 71
Rss-limited read: format data digits (variable) checksum1 (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion gr...
Page 72
Min. Code length 00-64 00-64 01 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ ucc/ean128 emulation disable enable 00 ＊ 01 exit 72.
Page 73
Rss-expanded read: format data digits (variable) checksum1 (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion g...
Page 74
Min. Code length 00-64 00-99 01 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 00-44 00 ＊ ucc/ean128 emulation disable enable 00 ＊ 01 exit 74.
Page 75
China post read: format data digits (variable) checksum1 (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion gro...
Page 76
Truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 00-ffh ＊ insert group selection 00-44 01-44 00 ＊ exit 76.
Page 77
Italian pharmacode read: format data digits (variable) checksum1 (optional) max./min. Code length: refer to max./min. Code length of code-39. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinser...
Page 78
Min. Code length 00-64 00-64 09 ＊ truncate leading 0-15 00-15 00 ＊ truncate ending 0-15 00-15 00 ＊ code id setting 00-ffh ascii code 01-ffh ＊ insert group selection 00-44 00-44 00 ＊ leading “a” disable enable 00 ＊ 01 exit 78.
Page 79
Code-16k only the zb-8210 can decode code-16k. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group selection of upca. Program option bar code option alphanumeric entry read disable en...
Page 80
Pdf-417 only the zb-8210 can decode pdf-417. Truncate leading/ending: refer to truncate leading/ending of upca. Code id setting: refer to code id setting of upca. Insertion group selection: refer toinsertion group selection of upca. Option bar code option alphanumeric entry read disable enable 00 01...
Page 81
String setting prefix characters: up to 22 ascii characters may be sent before data digits. Prefix data digits suffix suffix characters: up to 22 ascii characters may be sent after data digits. Preamble/ postamble characters: they are appended to the data automatically when each barcode is decoded. ...
Page 82
Preamble characters setting none 1-22 characters 00 ＊ 00-ffh ascii code postamble characters setting none 1-22 characters 00 ＊ 00-ffh ascii code insert g1 characters setting none 1-22 characters 00 ＊ 00-ffh ascii code insert g2 characters setting none 1-22 characters 00 ＊ 00-ffh ascii code insert g3...
Page 83
String setting insert g1/g2/g3/g4 character setting: the scanner offer 4 positions and 4 characters to insert among the symbol. Example: barcode “1 2 3 4 5 6”. Output- barcode “1 2 a b 3 4 c d 5 6”. Steps: 1) scan programming andinsert g1 characters setting barcode. 2) use the ascii code table to fi...
Page 84
Insert g3 characters setting none 1-22 characters 00 ＊ 00-ffh ascii code insert g4 characters setting none 1-22 characters 00 ＊ 00-ffh ascii code exit 84.
Page 85
Transmission preamble transmission: by setting enable, preamble will be appended before the data transmitted. Postamble transmission: by setting enable, postamble will be appended after the data is transmitted. Insert data group 1-4 position: the scanner offers 4 positions to insert among the symbol...
Page 86
Insert data group 1 position 00-64 (00: no insertion) 00-64 00 ＊ insert data group 2 position 00-64 (00: no insertion) 00-64 00 ＊ insert data group 3 position 00-64 (00: no insertion) 00-64 00 ＊ insert data group 4 position 00-64 (00: no insertion) 00-64 00 ＊ code id position before code data after ...
Page 87
Transmission code id transmission: if your application is needed to transmit code id, you must set this to proprietary id or aim id. Code length transmission: a number of data digits can be transmitted before the code data when enable is selected. The total length of the barcode is the number of bar...
Page 88
Code length transmission disable enable 00 ＊ 01 code name transmission disable enable 00 ＊ 01 case conversion disable upper case lower case *for barcode data only 00 ＊ 01 02 exit format of barcode data transmission: prefix name preamble id code length barcode data id postamble suffix insert groups 8...
Page 89
Test chart codabar-para code-11 para code-128 para code-39 para code-93 para ean-13 para 89.
Page 90
Pdf-417 standrad-25 para code-16k ean-8 para industrial-25 para upce para 87549 90
Page 91
Interleaved-25 para matrix 25 para msi/plessey para upca para uk/plessey para 91.
Page 92
Ascii code table note: for keyboard wedge only. L h 0 1 0 1 0 null nul dle 1 up f1 soh dc1 2 down f2 stx dc2 3 left f3 etx dc3 4 right f4 eot dc4 5 pgup f5 enq nak 6 pgdn f6 ack syn 7 f7 bel etb 8 bs f8 bs can 9 tab f9 ht em a f10 lf sub b home esc vt esc c end f11 ff fs d enter f12 cr gs e insert c...
Page 93
Parameter setting list program barcode standard parameter setting list if you wish to display the current configuration of your zb-8110/8150/8210, scanner over the host terminal/computer, scan the barcode standard parameter setting list bar code. Unique parameter list if you wish to display the uniq...
Page 94
Firmware version list if you wish to display the firmware version, scan the firmware version list. Warning: default value initialization if you wish to return the zb-8110/8150/8210 to all the factory default settings, scan the default value initialization bar code. Exit 94.
Page 95
97 0 a 1 b 2 c 3 d 4 e 5 f 6 7 8 finish 9 95.