Buoyancy compensator owner’s manual systems, inc..
Introduction 1 thanks for choosing zeagle! We value your decision to invest in a zeagle buoyancy control system. Please have your authorized zeagle dealer familiarize you with the operation and care of your new zeagle buoyancy compensator* (bc) and go over your owner’s manual with you. Have your dea...
Contents 2 introduction .......................................................................... 1 warranty information ........................................................... 3 general information and specifications ............................... 4 function of the zeagle system ................
3 warranty information lifetime guarantee to the original owner your bc is guaranteed against defects in materials and workmanship. This guarantee does not cover damages from accident, abuse, neglect, alterations, improper usage, or failure to provide reasonable care. To validate your warranty you m...
4 general information and specifications this buoyancy compensators owner's manual contains important safety, maintenance, and operation information. Read this manual thoroughly before diving. Important information on the assembly, operation, and maintenance of your bc is designated throughout this ...
Tank pictogram 19 xx max liters 5 general information & specifications scuba cylinder selection and configuration the maximum single and double cylinder size specifications (in liters) for the bc is found on a tank pictogram on the warning label. This label is found on the bc, inside the vest. If th...
6 general information and specifications operating temperature range table 1.0 180 n (rounded down to nearest 10 n) pren1809 44 lbs / 19 kg b u o y ancy t otal air -4 o to +122 o f -20 o to +50 o c water +28 o to +104 o f - 2 o to +40 o c surface buoyancy of bc's your bc's buoyancy, has been rated b...
7 function of the zeagle system the zeagle buoyancy control system the function of the zeagle buoyancy control system is to add to your diving enjoyment. It is designed to provide you with a comfortable way of “wearing” your scuba system, a resting platform while on the surface, and an easy means of...
8 function of the zeagle system clips must be attached to vest. Surface buoyancy label location do not dive with the two forward small side release buckles detached! Bladder assembly there are three basic bladder assemblies used on zeagle bc’s. The bladder assembly attaches to the vest section via t...
9 1999 in g od we tru st 1 2 1999 in g od we tru st adjusting side panels 1.Using two coins, unscrew the plastic screw fasteners. 2.Move the side panel to different set of grommets on vest and reinstall. Fitting and assembly.
10 1 2 6 3 4 5 illustration “a” non-slip plate (standard system only) (single cylinder band assembly) fitting and assembly illustration “b” threading the standard single cylinder system 1. Thread cylinder band through non-slip plate and then under the bottom center backplate straps as shown in illus...
11 there are only minor differences on a twin cylinder model. The rubber “nonslip” plate should be completely installed on the bottom band opposite the touch fastener material on the band, before inserting the band under the webbing on the pack. The bands go under the vertical webbing on the back pl...
12 fitting and assembly threading the quick release system for a single cylinder on twin cylinder back plate.
13 fitting and assembly scout single cylinder band system quick release fully closed.
14 proper fit the zeagle system allows the diver to size each component of the buoyancy system independently for a true custom fit. For proper performance please be sure that your system fits as described below. Put bc on (before attaching to scuba cylinder) and adjust shoulders and waist as follows...
15 adjust the bc so that it does not restrict your breathing. Restriction of normal breathing while wearing your bc could result in injury or death. Before each dive, check all bands, straps, clips, and/or waist panels for proper adjustment. Pre-dive assembly and inspection over pressure (op valve)/...
16 pre-dive assembly and inspection weight system inspection check to see that weight release system is secure. Ripcord ™ release system - check bottom of weight pockets to be sure they are held closed by the ripcord. If the ripcord has been pulled, rethread the system. (refer to the rethreading sec...
17 pre-dive assembly and inspection • return ripcord handle to secure position. • pull cord through for the right weight pocket. • start with the loop closest to the ripcord handle. • each white nylon loop is threaded through three grommets. The cord is then threaded through the end of the white loo...
18 pre-dive assembly and inspection loading the zeagle integrated weight system: loading: weights can be loaded after the system is donned as shown or the weights can be loaded before the system is donned. Considerations include the amount of weight and the distance to enter the water. Ask your budd...
19 donning procedure diving equipment is heavy! To avoid injury or fatigue and to become familiar with each other's equipment, have your buddy assist you! Take this opportunity to be sure your buddy understands how your weight release works. Be sure you have read and performed the proper fit page in...
20 diving with the zeagle system diving • start descent by releasing air slowly either through the inflator by holding the exhaust over your head and pushing on the exhaust button or by pulling gently (approximately 1/2 inch) on the inflator to open the remote exhaust valve on the shoulder if your s...
21 emergency procedures emergency weight release if you are diving with a buoyant wet or drysuit, be aware that releasing weights at depth should only be done if absolutely necessary (for example, if your drysuit has flooded, making you extremely negative). Without weights, it may be very difficult ...
22 emergency procedures problem management inflator problem inflators may fail due to foreign material in the mechanism, damage from impact by tanks or weights, or other causes. Practice the procedures below for your safety. Inflator fails to operate check to see that the low pressure hose is proper...
23 maintenance use of non-factory parts or accessories, or any change to the product not specifically authorized by zeagle systems, inc., or performed by an unautho- rized repair facility, may cause improper operation, damage, or leakage of the bc resulting in a loss of buoyancy control or air holdi...
24 owner orientation service record service record dealer preparation service performed service center technician # date.
Notes: service locating service and support the dealer that sold you your buoyancy compensator will be able to assist you with additional questions regarding product operation, warranty, and service. Your local zeagle dealer: (dealer to affix stamp here).
Zeagle systems, inc. 37150 chancey road zephyrhills, fl. 33541 phone: (813) 782-5568 fax: (813) 782-5569 www.Zeagle.Com for those products bearing the mark: ec type examination by: sgs yarsley international certification services ltd. Sgs house, portland road east grinstead rh19 4 et england notifie...
