1. DL manuals
  2. Zeagle
  3. Diving Instrument
  4. Buoyancy Compensator
  5. Owner's Manual

Zeagle Buoyancy Compensator Owner's Manual

Manual is about: Zeagle Buoyancy Control

Summary of Buoyancy Compensator

  • Page 1

    Buoyancy com pen sa tor owner’s man u al.

  • Page 2: Introduction

    Introduction 1 thanks for choosing zeagle! We value your decision to invest in a zeagle buoyancy control system. Please have your authorized zeagle dealer familiarize you with the operation and care of your new zeagle buoyancy compensator* (bc) and go over your owner’s manual with you. Have your dea...

  • Page 3: Contents

    Contents 2 introduction .................................................................. 1 warranty information .................................................... 3 general information and specifications ...................... 4 function of the zeagle system ..................................... ...

  • Page 4: Warranty Information

    3 warranty information limited lifetime guarantee to the original owner your bc is guaranteed against defects in materials and workman- ship. This guarantee does not cover damages from accident, abuse, neglect, alterations, improper usage, normal wear & tear or failure to provide reasonable care. To...

  • Page 5

    4 general information and specifications this buoyancy compensator's owner's manual contains important safety, maintenance, and operation information. Read this manual thoroughly before diving. Important information on the assembly, operation, and mainte- nance of your bc is designated throughout thi...

  • Page 6

    Tank pictogram 19 xx max liters 5 general information & specifications scuba cylinder selection and configuration the maximum single and double cylinder size specifications (in liters) for the bc is found on a tank pictogram on the warning label. This label is found on the bc, inside the vest. If the d...

  • Page 7: Operating Temperature Range

    6 general information and specifications operating temperature range table 1.0 180 n (rounded down to nearest 10 n) pren1809 44 lbs / 19 kg buoy ancy total air -4 o to +122 o f -20 o to +50 o c water +28 o to +104 o f - 2 o to +40 o c surface buoyancy of bc's your bc's buoyancy, has been rated by zea...

  • Page 8: Vest

    7 function of the zeagle system the zeagle buoyancy control system the function of the zeagle buoyancy control system is to add to your diving enjoyment. It is designed to provide you with a comfortable way of “wearing” your scuba system, a resting platform while on the surface, and an easy means of...

  • Page 9: Bladder Assembly

    8 function of the zeagle system the winglet side release buckles must be attached to the vest. Surface buoyancy label location do not dive with the two winglet side release buckles detached! Bladder assembly the bladder assembly attaches to the vest section via four stainless steel slotted fasteners...

  • Page 10: Adjusting The Side Panels

    9 adjusting the side panels 1. Using two coins, unscrew the plastic barrel-screw fasteners. 2. Move the side panel to different set of grommets on vest and re in stall. Fitting and assembly 3. Note that one extra plastic barrel-screw is installed in an unused grommet hole when the bcd leaves the fac...

  • Page 11: Fitting And As Sem Bly

    10 illustration “a” non-slip plate (standard system only) (single cylinder band assembly) fitting and as sem bly illustration “b” threading the stan dard single cylinder system note: tank bands expand and lengthen when wet. For this reason, you will get a tighter fi t if you make your initial adjustm...

  • Page 12: Fitting And Assembly

    11 there are only minor differences on a twin cylinder model. The rubber “non slip” plate should be completely installed on the bottom band oppo- site the touch fastener (velcro) material on the band, before inserting the band under the webbing on the pack. The bands go under the vertical webbing on...

  • Page 13: Fitting And Assembly

    12 quick release fully closed fitting and assembly mounting optional backplate for use with double tanks backplate available in: black anodized aluminum p/n 519-bp01a stainless steel p/n 519-bp01s titanium p/n 519-bp01t for ranger, ranger ltd, tec, tec-pac, 911 and sar bcds. May require modification ...

  • Page 14: Optional Double T

    13 optional double t ank bands and mounting systems for ranger , ranger ltd, t ec, t ec-pac, 91 1 and sar bcds..

  • Page 15: Proper Fit

    14 proper fit the zeagle personal fit system allows the diver to size each component of the buoyancy system independently, for a true custom fit. For proper performance, please be sure that your system fits as described below. Put the bc on (before attaching it to a scuba cylinder) and adjust the shou...

  • Page 16: Over Pressure Valve (Opv)

    15 adjust the bc so that it does not restrict your breathing. Restriction of nor- mal breathing while wearing your bc could result in injury or death. Before each dive, check all bands, straps, clips, and/or waist panels for proper adjustment. Pre-dive assembly and inspection over pressure valve (op...

  • Page 17: Weight System Inspection

    16 pre-dive assembly and inspection weight system inspection check to see that weight release system is secure. Ripcord ™ release system - check bottom of weight pockets to be sure they are held closed by the ripcord. If the ripcord has been pulled, re- thread the system. (refer to the re-threading ...

  • Page 18: Re-Threading The Ripcord

    17 pre-dive assembly and inspection • return the ripcord handle to the secure position. • pull the cord through for the right side weight pocket. • start with the loop closest to the ripcord handle. • each white nylon loop is threaded through three grommets. The cord is then threaded through the end...

  • Page 19

    18 pre-dive assembly and inspection loading the zeagle integrated weight system: weights can be loaded after the system is donned as shown, or the weights can be loaded before the system is donned. Considerations in- clude the amount of weight and the distance to enter the water. Ask your buddy for ...

  • Page 20: Donning Procedure

    19 donning procedure diving equipment is heavy! To avoid injury or fatigue and to become familiar with each other's equipment, have your buddy assist you! Take this opportunity to be sure your buddy under- stands how your weight release works. Be sure you have read and performed the proper fit page ...

  • Page 21: Diving

    20 diving with the zeagle system diving • your final buoyancy is primarily affected by your body, your thermal suit, your diving cylinder, and your lead weights. It is adjusted with your bcd. Both too little and too much lead ballast can be dangerous. To determine the proper amount of lead ballast we...

  • Page 22: Emergency Pro Ce Dures

    21 emergency pro ce dures emergency weight release if you are diving with a buoyant wet or drysuit, be aware that releasing weights at depth should only be done if ab so lute ly necessary (for example, if your drysuit has fl ooded, making you extremely negative). Without weights, it may be very diffi ...

  • Page 23: Emergency Procedures

    22 emergency procedures problem management inflator problem inflators may fail due to foreign material in the mechanism, damage from impact by tanks or weights, or other causes. Practice the procedures below (in a safe location with your buddy) for your safety. Inflator fails to operate check to see th...

  • Page 24: Maintenance

    23 maintenance use of non-factory parts or accessories, or any change to the product not specifically authorized by zeagle systems, inc., or performed by an unauthorized repair facility, may cause improper operation, damage, or leakage of the bc resulting in a loss of buoyancy control or air holding ...

  • Page 25: Buoyancy System Accessories

    24 buoyancy system accessories pony bottle attachment kit 8029hd mounts a pony bottle securely to any zeagle bc shot weight pouches 8042(12-lb) 8043(20-lb) full lumbar pad 7275f strobe/flashlight 8036 bc pocket (clip closure) 8033cc diver tool kits 8135 without slate 8135s with slate spare air pocke...

  • Page 26: Locating Service and Support

    Locating service and support the dealer that sold you your buoyancy compensator will be able to assist you with additional questions regarding product op- eration, warranty, and service. Go to www.Zeagle.Com for dealer locations near you. Your local zeagle dealer: (dealer to affix stamp here) attach ...

  • Page 27: Zeagle Systems,

    Zeagle systems, inc. 37150 chancey road zephyrhills, fl. 33541 phone: (813) 782-5568 fax: (813) 782-5569 www.Zeagle.Com for those products bearing the ce mark: ec type examination by: sgs yarsley international certification services limited sgs house portland road east grinstead, west sussex rh19 4et...