1. DL manuals
  2. Zebra
  3. Wireless Access Point
  4. AP-6521E Series
  5. Installation Manual

Zebra AP-6521E Series Installation Manual - 1.5    Features

Summary of AP-6521E Series

  • Page 1

    Ap-6521e series access point installation guide.

  • Page 2

    2 ap-6521e series access point zebra and the zebra head graphic are registered trademarks of zih corp. The symbol logo is a registered trademark of symbol technologies, inc., a zebra technologies company. © 2015 symbol technologies, inc..

  • Page 3

    Installation guide 3 1.0 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.2 warnings . . . . . . . . . . . . ...

  • Page 4

    4 ap-6521e series access point 5.3.3 safety in hospitals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.4 rf exposure guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.4.1 safety information . . . . . . ....

  • Page 5: Introduction

    Installation guide 5 1 introduction an ap-6521 series access point links wireless 802.11a/b/g/n devices to the controller, enabling the growth of your wireless network with a cost-effective alternative to standard access points. The ap-6521 series access point is an enterprise class 802.11n access p...

  • Page 6: 1.2    Warnings

    6 ap-6521e series access point 1.1 document conventions the following graphical alerts are used in this document to indicate notable situations: 1.2 warnings • read all installation instructions and site survey reports, and verify correct equipment installation before connecting the access point. • ...

  • Page 7: 1.5    Features

    Installation guide 7 1.5 features • one rj-45 console connector • led indicators • safety wire tie point • wall mount slots • clips for suspended t-bar mounting • dc power connector an ap-6521 series access point has one rj-45 connector supporting an 10/100/1000 ethernet port connection and requires...

  • Page 8: Hardware Installation

    8 ap-6521e series access point 2 hardware installation 2.1 installation instructions the access point can attach to a wall, mount under a suspended t-bar or mount above a ceiling. Select a mounting option based on the physical environment of the coverage area. Do not mount the access point in a loca...

  • Page 9: 2.3.1    Antenna Options

    Installation guide 9 2.3 access point placement for optimal performance, install the access point away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls or floors block transmissi...

  • Page 10

    10 ap-6521e series access point the 2.4 ghz antenna suite includes the following models: the 5 ghz antenna suite includes the following models: for a more exhaustive overview of the antennas and associated components supported, refer to the enterprise wireless lan antenna specification guide availab...

  • Page 11

    Installation guide 11 2.3.2 power injector system the access point can receive power via an ethernet cable connected to the ge1/poe port. When users purchase a wlan solution, they often need to place access points in obscure locations. In the past, a dedicated power source was required for each acce...

  • Page 12

    12 ap-6521e series access point the following guidelines should be adhered to before cabling the power injector to an ethernet source and an access point: • do not block or cover airflow to the power injector. • keep the power injector away from excessive heat, humidity, vibration and dust. • the po...

  • Page 13

    Installation guide 13 2.4 wall mount installation to support wall mount installations, the access point is fastened directly to a flat wall surface. The wall should be of gypsum board, plaster, wood or concrete in composition. To install the access point to a wall surface: 1. Orient the access point...

  • Page 14

    14 ap-6521e series access point e. Attach the power supply line cord to a power supply. 10. Verify the behavior of the access point leds. For more information, see led indicator . 11. The access point is ready to configure. For information on basic access point device configuration, see basic access...

  • Page 15

    Installation guide 15 6. Align the bottom of the ceiling t-bar with the back of the access point. 7. Orient the access point chassis by its length and the length of the ceiling t-bar. 8. Rotate the access point chassis 45 degrees clockwise. 9. Push the back of the access point chassis on to the bott...

  • Page 16

    16 ap-6521e series access point 2.6 above the ceiling (plenum) installation an above the ceiling installation requires placing the access point above a suspended ceiling and installing the provided light pipe under the ceiling tile for viewing the status led of the unit. An above the ceiling deploym...

  • Page 17

    Installation guide 17 9. Place the decal on the back of the badge and slide the badge onto the light pipe from the finished side of the tile. 10. Attach the antennas to their correct connectors. 11. Align the ceiling tile into its former ceiling space. 12. Cable the access point using either the pow...

  • Page 18: 2.7    Led Indicator

    18 ap-6521e series access point 2.7 led indicator an ap-6521 series access point has a single led activity indicator on the front of the unit. The led provides a status display indicating error conditions, transmission, and network activity for the 5 ghz 802.11a/n (amber) radio or the 2.4 ghz 802.11...

  • Page 19

    Installation guide 19 3 basic access point configuration for a wing express sku (ap-6521e), both the ui and an over the air (ota) provisioning configuration are required for a basic setup and network connection. For a non wing express sku (ap-6521), there’s no ota support, and the access point utili...

  • Page 20

    20 ap-6521e series access point 3. Enter the default username admin in the username field. 4. Enter the default password admin123 in the password field. 5. Select the login button to load the management interface. If this is the first time the wing express interface has been accessed, a screen displ...

  • Page 21

    Installation guide 21 7. Expand the configuration menu item and select basic . 8. Set the following basic configuration settings for this access point: • ap name - provide an ap name used as this access point’s wing express network identifier. If setting this access point as a virtual controller, ea...

  • Page 22

    22 ap-6521e series access point 10. Expand the configuration menu item and select wan . 11. Refer to the wan settings field and set the following: • enable - select this option to allow a connection between the access point and a larger network or outside world through the wan port. Disable this opt...

  • Page 23

    Installation guide 23 • static ip / mask - specify an ip address for the wan connection if using static address assignment for the wan port. An ip address uses a series of four numbers expressed in dot notation, for example, 190.188.12.1. Additionally, specify a mask for the access point’s wan conne...

  • Page 24

    24 ap-6521e series access point 14. Select apply to commit the updates to the selected access point’s configuration. 15. Expand the configuration menu item and select wireless . The wireless screen displays fields where radio settings and wireless lan settings can be defined. It is recommended defau...

  • Page 25

    Installation guide 25 16. To create a new wlan, select + add from the upper, left-hand side of the wireless lan field. 17. Set the following configuration attributes for the new wlan: • name - provide a unique name for the wlan as its wing express network identifier. This is a required setting. • en...

  • Page 26

    26 ap-6521e series access point • ssid - specify the wlan's ssid. The wlan ssid is case sensitive and alphanumeric. Ssid length should not exceed 32 characters. This is a required setting. Select client-to-client communication to enable client interoperability within this wlan. The default is disabl...

  • Page 27

    Installation guide 27 19. Expand the configuration menu item and select services . 20. Select enable dhcp server to ensure the access point can provision ip addresses to requesting clients over the specified interface. Select + add and provide a starting and ending ip range of addresses that constit...

  • Page 28: Specifications

    28 ap-6521e series access point 4 specifications 4.1 electrical characteristics an ap-6521 series access point has the following electrical characteristics: 4.2 physical characteristics an ap-6521 series access point has the following physical characteristics: max dc power consumption 12.95w (270ma@...

  • Page 29

    Installation guide 29 4.3 radio characteristics an ap-6521 series access point has the following radio characteristics: operating channel (2.4 ghz) channel 1 to 13 (2412 to 2472 mhz) *japan only - channel 14 (2484 mhz) operating channel (5. Ghz) channels 36 - 165 802.11a data rates 6, 9, 12, 18, 24,...

  • Page 30: Regulatory Information

    30 ap-6521e series access point 5 regulatory information 5.1 regulatory overview this guide applies to part numbers ap-6521-60010-us, ap-6521-60020-us, ap-6521-60010-eu, ap-6521-60020-eu, ap-6521-60010-wr, ap-6521-60020-wr, ap-6521e-60010-us, ap-6521e-60020-us, ap-6521e-60010-eu, ap-6521e-60020-eu, ...

  • Page 31

    Installation guide 31 5.2.2 frequency of operation – fcc and ic 5 ghz only the use on unii (unlicensed national information infrastructure) band 1 5150-5250 mhz is restricted to indoor use only, any other use will make the operation of this device illegal. Industry canada statement: caution: the dev...

  • Page 32: 5.5    International

    32 ap-6521e series access point persons with pacemakers: • should always keep the device more than 15cm (6 inches) from their pacemaker when turned on. • should not carry the device in a breast pocket. • should use the ear furthest from the pacemaker to minimize the potential for interference. • if ...

  • Page 33: 5.8    Power Supply

    Installation guide 33 5.8 power supply this device is powered from a 802.3af compliant power source which is ul approved and certified by the appropriate agencies. 5.9 radio frequency interference requirements—fcc this equipment has been tested and found to comply with the limits for a class b digit...

  • Page 34: 5.12    Mexico

    34 ap-6521e series access point brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable label marking: the term "ic:" before the radio certification only signifies that industry canada technical...

  • Page 35

    Installation guide 35 5.14 waste electrical and electronic equipment (weee) english: for eu customers: all products at the end of their life must be returned to zebra for recycling. For information on how to return product, please go to: www.Zebra.Com/weee . Français: clients de l'union européenne: ...

  • Page 36

    36 ap-6521e series access point malti: g ħ al klijenti fl-ue: il-prodotti kollha li jkunu waslu fl-a ħħ ar tal- ħ ajja ta' l-u ż u tag ħ hom, iridu ji ġ u rritornati g ħ and zebra g ħ ar-ri ċ ikla ġġ . G ħ al aktar tag ħ rif dwar kif g ħ andek tirritorna l-prodott, jekk jog ħġ bok ż ur: www.Zebra.Co...

  • Page 37: 5.17    Other Countries

    Installation guide 37 5.15 japan (vcci) - voluntary control council for interference class b ite this is a class b product based on the standard of the voluntary control council for interference from information technology equipment (vcci). If this is used near a radio or television receiver in a do...

  • Page 38: Chile

    38 ap-6521e series access point chile “este equipo cumple con la resolución no 403 de 2008, de la subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas.”. "this device complies with the resolution not 403 of 2008, of the undersecretary of telecommunications, relating to elect...

  • Page 39: Korea

    Installation guide 39 wireless devices operate in the frequency band of 5.25-5.35 ghz, limited for indoor use. Korea for radio equipment using 2400~2483.5mhz or 5725~5825mhz, the following expressions should be displayed: 1. “this radio equipment cannot provide a service relevant to human life safet...

  • Page 40: Support

    40 ap-6521e series access point 6 support if you have a problem with your equipment, contact support for your region. Contact information is available at: www.Zebra.Com/support . When contacting support, please provide the following information: • serial number of the unit • model number or product ...

  • Page 41

    Installation guide 41 7 ap-6521 series access point china rohs compliance 本表格依据 sj/t 11364 的规定编制。 o: 表示该有害物质在该部件所有均质材料中的含量均在 gb/t 26572 规定的限量 要求以下。 x: 表示该有害物质至少在该部件的某一均质材料中的含量超出 gb/t 26572 规定 的限量要求。 ( 企业 可在此处，根据实际情况对上表中打 “×” 的技术原因进 行进一步说明。） this table was created to comply with china rohs requiremen...

  • Page 42

    42 ap-6521e series access point.

  • Page 44

    Zebra technologies corporation lincolnshire, il 60069 usa zebra and the zebra head graphic are registered trademarks of zih corp. The symbol logo is a registered trademark of symbol technologies, inc., a zebra technologies company. Mn001366a01 revision b april 2015.