- DL manuals
- Zebra
- Printer
- ZT200 series
- Wireless Quick Start Manual
Zebra ZT200 series Wireless Quick Start Manual - Power Cord Specifications
15
Printer Setup
Power Cord Specifications
5/31/12
P1050133-002
Power Cord Specifications
Depending on how your printer was ordered, a power cord may or may not be included. If one
is not included or if the one included is not suitable for your requirements, see
Figure 2
and
refer to the following guidelines:
• The overall cord length must be less than 9.8 ft. (3 m).
• The cord must be rated for at least 10 A, 250 V.
• The chassis ground (earth) must be connected to ensure safety and reduce electromagnetic
interference.
Figure 2 • Power Cord Specifications
Figure 3 • International Safety Organization Certifications
Caution • For personnel and equipment safety, always use an approved three-conductor
power cord specific to the region or country intended for installation. This cord must use an
IEC 320 female connector and the appropriate region-specific, three-conductor grounded
plug configuration.
1
AC power plug for your country—This should bear
the certification mark of at least one of the known
international safety organizations (
Figure 3
).
2
3-conductor HAR cable or other cable approved for
your country.
3
IEC 320 connector—This should bear the
certification mark of at least one of the known
international safety organizations (
Figure 3
).
4
Length
≤ 9.8 ft. (3 m). Rating 10 Amp, 250 VAC.
3
1
2
4
Summary of ZT200 series
Page 1
P1050133-002 zebranet ® wireless quick start guide for xi™ series, rxi™ series, pax4™ series, z series ® , rz™ series, hc100™, s4m™, 105sl™, zt200™ series, and ze500™series printers.
Page 2
Copyright and liability disclaimer 2 p1050133-002 05/31/2012 © 2012 zih corp. The copyrights in this manual and the software and/or firmware in the printer described therein are owned by zih corp. And zebra’s licensors. Unauthorized reproduction of this manual or the software and/ or firmware in the...
Page 3
5/31/12 p1050133-002 contents 1 • about this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 who should use this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 how this document is organized . . . ....
Page 4
Contents 4 p1050133-002 5/31/12 xi series and rxi series compliance information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 fcc compliance statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 fcc radiation exposure statement (for pri...
Page 5
5 contents 5/31/12 p1050133-002 z series and rz series general specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 electrical specifications . . . ...
Page 6
Contents 6 p1050133-002 5/31/12 s4m general specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 electrical specificat...
Page 7
7 contents 5/31/12 p1050133-002 zt210, zt220, and zt230 compliance information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 fcc compliance statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 canadian doc compliance statement . . . . . ....
Page 8
Contents 8 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ __________________________________________...
Page 9
5/31/12 p1050133-002 1 about this document this section provides you with contact information, document structure and organization, and additional reference documents. Contents who should use this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 how t...
Page 10: Who Should Use This Document
About this document who should use this document 10 p1050133-002 5/31/12 who should use this document this guide is intended for use by someone who needs to configure and use a zebranet wireless print server for use with a supported printer. This guide supports the zebranet wireless print server, th...
Page 11: Document Conventions
11 about this document document conventions 5/31/12 p1050133-002 document conventions the following conventions are used throughout this document to convey certain information. Printer/print engine the term “printer” will be used throughout this document to refer to zebra printers and print engines....
Page 12: Contacts
About this document contacts 12 p1050133-002 05/31/2012 contacts technical support via the internet is available 24 hours per day, 365 days per year. Web site: www.Zebra.Com e-mail back technical library: e-mail address: emb@zebra.Com subject line: emaillist self service knowledge base: www.Zebra.Co...
Page 13
5/31/12 p1050133-002 2 printer setup this section provides the tasks that you must complete and the issues that you must consider before you load and configure your printer. Contents before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 14: Before You Begin
Printer setup before you begin 14 p1050133-002 5/31/12 before you begin review this checklist, and resolve any issues before you set up or use your wireless printer. unpack and inspect the printer have you unpacked the printer and inspected it for damage? When you receive the printer, immediately ...
Page 15: Power Cord Specifications
15 printer setup power cord specifications 5/31/12 p1050133-002 power cord specifications depending on how your printer was ordered, a power cord may or may not be included. If one is not included or if the one included is not suitable for your requirements, see figure 2 and refer to the following g...
Page 16
Printer setup connect the printer to a power source 16 p1050133-002 5/31/12 connect the printer to a power source for pax4 print engines, the power supply in the print engine automatically detects the applied line voltage and works in the 90 to 264 vac, 47 to 63 hz range. The ac power cord must have...
Page 17
17 printer setup select a wired data communication interface 5/31/12 p1050133-002 select a wired data communication interface to configure your printer for wireless operation, you must first connect your printer using a wired data communication interface. Table 1 provides basic information about wir...
Page 18
Printer setup select a wired data communication interface 18 p1050133-002 5/31/12 data cables and wireless cards you must supply all data cables or removeable radio cards for your application. (some wireless print servers come with an integrated radio card.) data cables ethernet cables do not requir...
Page 19
5/31/12 p1050133-002 3 wireless configuration use this section to configure your zebranet wireless print server for operation. For more detailed information, refer to the zebranet wired and wireless print servers user guide. You may configure your printer for wireless operation in the following ways...
Page 20
Wireless configuration configure using the network setup wizard 20 p1050133-002 5/31/12 configure using the network setup wizard the zebranet bridge enterprise utility resides on the user cd for your printer and is available through http://www.Zebra.Com/software . Zebranet bridge enterprise version ...
Page 21
21 wireless configuration configure using the network setup wizard 5/31/12 p1050133-002 4. From the choose port list, select the port to which your printer is connected. • if you will save the file without sending it to the printer, you may select any available port. • if you select a serial port, t...
Page 22
Wireless configuration configure using the network setup wizard 22 p1050133-002 5/31/12 5. Click next . The wizard prompts for the print server device to configure. 6. Select wireless and then click next . The wizard prompts you for the type of printer you are using..
Page 23
23 wireless configuration configure using the network setup wizard 5/31/12 p1050133-002 7. Select the type of printer you are using and then click next . The wizard prompts for the wireless ip information..
Page 24
Wireless configuration configure using the network setup wizard 24 p1050133-002 5/31/12 8. Enable the dhcp (dynamic) or static ip option. 9. Click next . The wireless settings window opens. 10. Enter the essid. If you will be using... Complete the following steps... Dhcp a. Select dhcp and click nex...
Page 25
25 wireless configuration configure using the network setup wizard 5/31/12 p1050133-002 11. From the drop-down, select your security mode. If you select… then… none continue with step 12 . Wep 40-bit wep 128-bit a. In the wep options section of the window, enter the following values: • authenticatio...
Page 26
Wireless configuration configure using the network setup wizard 26 p1050133-002 5/31/12 12. Click advanced options in the wireless settings window. The advanced wireless settings window opens. 13. Review the settings in the advanced wireless settings window. Change the settings as necessary, and the...
Page 27
27 wireless configuration configure using the network setup wizard 5/31/12 p1050133-002 14. Click next . Based on your selections in the wireless setup wizard, the program writes the appropriate zpl commands and displays them for your review. If you selected… then this dialog box displays. Tabletop/...
Page 28
Wireless configuration configure using the network setup wizard 28 p1050133-002 5/31/12 15. Determine if you will send the script immediately, or save it for use at a later time. To... Then... Complete setup by sending the zpl script to the printer through the port selected at the beginning of this ...
Page 29
29 wireless configuration configure using the network setup wizard 5/31/12 p1050133-002 16. Observe the wireless status on the printer’s control panel, and confirm that you have set up your printer for wireless connectivity. Printers that have an lcd display text or symbols (see table 2 and table 3 ...
Page 30
Wireless configuration configure using the network setup wizard 30 p1050133-002 5/31/12 hc100 wireless status indicator lights table 4 • hc100 wireless status indicator lights wireless status indicator meaning steady green the printer is associated with a wireless network. The signal strength is str...
Page 31
5/31/12 p1050133-002 4 xi series and rxi series this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents select a site for the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 32
Xi series and rxi series select a site for the printer 32 p1050133-002 5/31/12 select a site for the printer consider the following when selecting an appropriate location for your printer. Select a surface select a solid, level surface of sufficient size and strength to accommodate the printer and o...
Page 33
33 xi series and rxi series xi4 and r110xi4 general specifications 5/31/12 p1050133-002 xi4 and r110xi4 general specifications physical specifications electrical specifications environmental conditions for operation and storage dimensions 110xi4/r110xi4 140xi4 170xi4 220xi4 u.S. Standard metric u.S....
Page 34
Xi series and rxi series xi series and rxi series compliance information 34 p1050133-002 5/31/12 xi series and rxi series compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmfu...
Page 35
35 xi series and rxi series xi series and rxi series compliance information 5/31/12 p1050133-002 korean compliance statement 이 기기는 가정용 (b 급 ) 전자파 적합기기 로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지 역에서 사용할 수 있습니다 . The equipment is for home use (class b) and has acquired electromagnetic conformity registration, ...
Page 36
Xi series and rxi series xi series and rxi series compliance information 36 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ ____________________________________________________...
Page 37
5/31/12 p1050133-002 5 pax 4 series this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents print engine installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 38: Print Engine Installation
Pax4 series print engine installation 38 p1050133-002 5/31/12 print engine installation this section provides basic information for mounting the print engine into an applicator. The illustrations in this section show the print engine from different angles and include dimensions and clearance needs. ...
Page 39
39 pax4 series select a site for the printer 5/31/12 p1050133-002 select a site for the printer consider the following when selecting an appropriate location for your printer. Stability when the print engine is mounted, the complete assembly must be physically stable. When the print engine is loaded...
Page 40
Pax4 series select a site for the printer 40 p1050133-002 5/31/12 provide a power source place the printer within a short distance of a power outlet that is easily accessible. Power requirements consider the current rating of the print engine during installation. When power is applied to the print e...
Page 41
41 pax4 series 110pax4 and r110pax4 general specifications 5/31/12 p1050133-002 110pax4 and r110pax4 general specifications physical electrical specifications environmental conditions dimensions 110pax4/r110pax4 u.S. Standard metric height 11.8 in 300 mm width 9.6 in. 245 mm depth 16.4 in. 417 mm we...
Page 42
Pax4 series 170pax4 general specifications 42 p1050133-002 5/31/12 170pax4 general specifications physical electrical specifications environmental conditions dimensions 170pax4 u.S. Standard metric height 11.8 in 300 mm width 9.6 in. 245 mm depth 18.3 in. 465 mm weight 35.5 lb 16.1 kg power general ...
Page 43: Pax4 Compliance Information
43 pax4 series pax4 compliance information 5/31/12 p1050133-002 pax4 compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any in...
Page 44
Pax4 series pax4 compliance information 44 p1050133-002 5/31/12 korean compliance statement the equipment is for business use (class a), and has acquired electromagnetic conformity registration. Sellers and users are required to take caution in this regard. This radio device is not allowed to be use...
Page 45
5/31/12 p1050133-002 6 z series and rz series this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents select a site for the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 46
Z series and rz series select a site for the printer 46 p1050133-002 5/31/12 select a site for the printer consider the following when selecting an appropriate location for your printer. Select a surface select a solid, level surface of sufficient size and strength to accommodate the printer and oth...
Page 47
47 z series and rz series z series and rz series general specifications 5/31/12 p1050133-002 z series and rz series general specifications physical specifications electrical specifications environmental conditions for operation and storage dimensions zm400/rz400 zm600/rz600 u.S. Standard metric u.S....
Page 48
Z series and rz series z series and rz series compliance information 48 p1050133-002 5/31/12 z series and rz series compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful inte...
Page 49
49 z series and rz series z series and rz series compliance information 5/31/12 p1050133-002 korean compliance statement 이 기기는 가정용 (b 급 ) 전자파 적합기기 로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지 역에서 사용할 수 있습니다 . The equipment is for home use (class b) and has acquired electromagnetic conformity registration, so i...
Page 50
Z series and rz series z series and rz series compliance information 50 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ ________________________________________________________...
Page 51
5/31/12 p1050133-002 7 hc100 this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents select a site for the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 52
Hc100 select a site for the printer 52 p1050133-002 5/31/12 select a site for the printer consider the following when selecting an appropriate location for your printer. Select a surface select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (suc...
Page 53: Hc100 General Specifications
53 hc100 hc100 general specifications 5/31/12 p1050133-002 hc100 general specifications physical specifications electrical specifications environmental conditions for operation and storage dimensions u.S. Standard metric height 7.0 in 178 mm width 5.0 in. 127 mm depth 9.5 in. 242 mm clearance - amou...
Page 54: Hc100 Compliance Information
Hc100 hc100 compliance information 54 p1050133-002 5/31/12 hc100 compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interf...
Page 55
55 hc100 hc100 compliance information 5/31/12 p1050133-002 ncc 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變 更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛 航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方 得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機 須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 according to "administrative regulations on low power radi...
Page 56
Hc100 hc100 compliance information 56 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _______________...
Page 57
5/31/12 p1050133-002 8 s4m this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents select a site for the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 58
S4m select a site for the printer 58 p1050133-002 5/31/12 select a site for the printer consider the following when selecting an appropriate location for your printer. Select a surface select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (such ...
Page 59: S4M General Specifications
59 s4m s4m general specifications 5/31/12 p1050133-002 s4m general specifications physical specifications electrical specifications environmental conditions for operation and storage dimensions u.S. Standard metric height 11.6 in. 295 mm width 10.7 in. 272 mm depth 18.8 in. 477 mm weight without opt...
Page 60: S4M Compliance Information
S4m s4m compliance information 60 p1050133-002 5/31/12 s4m compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference...
Page 61
61 s4m s4m compliance information 5/31/12 p1050133-002 ncc 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變 更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛 航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方 得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機 須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 according to "administrative regulations on low power radio wa...
Page 62
S4m s4m compliance information 62 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ___________________...
Page 63
5/31/12 p1050133-002 9 105 sl this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents select a site for the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 64
105sl select a site for the printer 64 p1050133-002 5/31/12 select a site for the printer consider the following when selecting an appropriate location for your printer. Select a surface select a solid, level surface of sufficient size and strength to accommodate the printer and other equipment (suc...
Page 65
65 105sl 105sl general specifications 5/31/12 p1050133-002 105sl general specifications physical specifications electrical specifications environmental conditions for operation and storage dimensions metric u.S. Standard height 394 mm 15.5 in width 284 mm 10.2 in. Depth 480 mm 18.9 in. Weight withou...
Page 66
105sl 105sl compliance information 66 p1050133-002 5/31/12 105sl compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interf...
Page 67
67 105sl 105sl compliance information 5/31/12 p1050133-002 ncc 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變 更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛 航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方 得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機 須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 according to "administrative regulations on low power radi...
Page 68
105sl 105sl compliance information 68 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ _______________...
Page 69
5/31/12 p1050133-002 10 zt200 series this section provides the features of and specifications for these printers. Note • printer specifications are subject to change without notice. Contents select a site for the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 70
Zt210 / zt220 / zt230 select a site for the printer 70 p1050133-002 5/31/12 select a site for the printer consider the following when selecting an appropriate location for your printer. Select a surface select a solid, level surface of sufficient size and strength to accommodate the printer and othe...
Page 71
71 zt210 / zt220 / zt230 zt210, zt220, and zt230 general specifications 5/31/12 p1050133-002 zt210, zt220, and zt230 general specifications physical specifications electrical specifications environmental conditions for operation and storage dimensions zt210 zt220 zt230 u.S. Standard metric u.S. Stan...
Page 72
Zt210 / zt220 / zt230 zt210, zt220, and zt230 compliance information 72 p1050133-002 5/31/12 zt210, zt220, and zt230 compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful int...
Page 73
73 zt210 / zt220 / zt230 zt210, zt220, and zt230 compliance information 5/31/12 p1050133-002 european regulatory information japan restricted frequencies for 5.725 - 5.825 ghz, this frequency band will not be available in japan. Taiwan restricted frequencies for 5.15 - 5.25 ghz, this frequency band ...
Page 74
Zt210 / zt220 / zt230 zt210, zt220, and zt230 compliance information 74 p1050133-002 5/31/12 ncc 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變 更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛 航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方 得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機 須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 according to "administra...
Page 75
5/31/12 p1050133-002 11 ze500 series this section provides the features of and specifications for this printer. Note • printer specifications are subject to change without notice. Contents print engine installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 76: Print Engine Installation
Ze500 series print engine installation 76 p1050133-002 5/31/12 print engine installation this section provides basic information for mounting the print engine into an applicator. The illustrations in this section show the print engine from different angles and include dimensions and clearance needs....
Page 77
77 ze500 series select a site for the printer 5/31/12 p1050133-002 select a site for the printer consider the following when selecting an appropriate location for your printer. Stability when the print engine is mounted, the complete assembly must be physically stable. When the print engine is loade...
Page 78
Ze500 series select a site for the printer 78 p1050133-002 5/31/12 provide a power source place the printer within a short distance of a power outlet that is easily accessible. Power requirements consider the current rating of the print engine during installation. When power is applied to the print ...
Page 79: Ze500 General Specifications
79 ze500 series ze500 general specifications 5/31/12 p1050133-002 ze500 general specifications physical electrical specifications environmental conditions dimensions ze500-4 ze500-6 u.S. Standard metric u.S. Standard metric height 11.8 in 300 mm 11.8 in 300 mm width 9.6 in. 245 mm 9.6 in. 245 mm dep...
Page 80: Ze500 Compliance Information
Ze500 series ze500 compliance information 80 p1050133-002 5/31/12 ze500 compliance information fcc compliance statement this device complies with part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any...
Page 81
81 ze500 series ze500 compliance information 5/31/12 p1050133-002 korean compliance statement the equipment is for business use (class a), and has acquired electromagnetic conformity registration. Sellers and users are required to take caution in this regard. This radio device is not allowed to be u...
Page 82
Ze500 series ze500 compliance information 82 p1050133-002 5/31/12 notes • ___________________________________________________________________ __________________________________________________________________________ __________________________________________________________________________ ________...
Page 84
Zebra technologies corporation zebra technologies corporation 475 half day road, suite 500 lincolnshire, il 60069 usa t: +1 847 634 6700 toll-free +1 866 230 9494 f: +1 847 913 8766 zebra technologies europe limited dukes meadow millboard road bourne end buckinghamshire, sl8 5xf, uk t: +44 (0)1628 5...