Summary of BIKE+
Page 1
Bike+ all in one user manual.
Page 3
3 read all safety warnings and all instruction. Failure to follow the warnings and instructions may result in serious injury. Save all safety warnings and instructions for future reference. O do not open the unit yourself. Bike+ all in one is maintenance-free and must be repaired only by qualified e...
Page 4
4 o if your bike+ all in one has a 6 pin connector (see figure 1), please be careful to insert the 6 pin charger plug in the 6-pin connector in the proper way. Otherwise short circuits can occur. Warranty is void if charger is not inserted correctly. Do not short circuit the pinout of the charging c...
Page 5
5 1. Getting started with bike+ all in one 1.1 intended use bike+ all in one is intended to be used exclusively with the bike which was sold with. Any attempt to mount bike+ all in one on another bike will void warranty claims. Bike+ all in one is not permitted for competition and race use. 1.2 init...
Page 6
6 1.4 turning off the system bike+ all in one automatically turns off when no activities are detected within 2 minutes, in order to reduce the idle battery use. In order to manually turn off bike+ all in one, lean the bike vertically or horizontally, as explained in figure 3 ! When a smartphone is c...
Page 7
7 2. Riding bike+ all in one ! It is recommended to gather first experience with bike+ all in one away from roads with heavy traffic. Bike+ all in one is an advanced powertrain for e-bikes that helps you in reducing your ped- aling effort. The system is compliant to the eu laws on electric pedal ass...
Page 8
8 the generated power depends on several factors including the bike speed, the pedal- ling speed and the road slope, depending on the selected power mode. The default power mode of bike+ all in one is the “turbo” mode. For instruction on how to change the power mode please refer to 4.4 and 4.6. 2.2 ...
Page 9
9 2.3 charging bike+ all in one (see figure 6) to charge bike+ all in one, simply remove the protection cap from the charging connec- tor (i) and plug in the zehus charger (2). Then connect the zehus charger to a power outlet (110~240 v). The charging time is approximately 3 hours for a complete cha...
Page 10
10 2.5 careful handling of the bike please observe the operating storage temperature of bike+ all in one. Protect the charging connector from impacts that can damage it. The components can be dam- aged if exposed to extreme temperatures. ! Caution: always seal the connector on bike+ all in one with ...
Page 11
11 3. Using a smartphone with your bike+ all in one in order to access all the function of bike+ all in one, you would have to connect a smartphone through the bitride app. 3.1 what is the bitride app? The bitride app helps you to act smarter during the everyday mobility; bitride also allows you to ...
Page 12
12 3.4 how much is the bitride app? The bitride app is available for free. 3.5 how do you install the bitride app? Depending on your mobile device, go either to the apple store or to google play and search for the bitride app. The detailed procedure is listed below. On iphone: o open app store o tap...
Page 13
13 on iphone: o open the bluetooth settings screen o tap your bike+ all in one name o wait for connection o launch bitride o using the upper screen menu, select ride o press connect ! Note: if you have an iphone bitride will auto-connect to your bike+ all in one after the first time the device is pa...
Page 14
14 3.7 bike+ registration (first use) ! Note: it is not mandatory to perform this action. Your bike+ all in one is ready to go and it is set into “turbo” power mode (for more power modes see 4.7) in order to use your bike+ all in one together with bitride, you need to register it using your bitride ...
Page 15
15 ! Note: the bike name will change at the first reboot of the bike. ! Internet connection needed to perform the registration internet smartphone.
Page 16
16 4. Bitride hmi for bike+ all in one even if it is possible to use bike+ all in one with out the bitride app, you can access more features if you connect it to a smartphone. To access the “ride” screen tap the hamburger menu on the upper left side of the screen and select ride. To access the onlin...
Page 17
17 4.1 using the dashboard (see figure 7) the bitride dashboard for bike+ all in one displays the following information: o bike speed [km/h] or [mi/h] o total odo [km] or [mi] o partial odo [km] or [mi] o road slope [%] o motor power [w] o state of charge of the battery [%] o active power mode (see ...
Page 18
18 figure 8: slope sensor calibration figure 9: locking / unlocking bike+ all in one bike bike + + trip trip slop slop e e % % 3 sec! 0 km/h! 0˚! % bike+ trip slope % i 2 3.
Page 19
19 ! Note: the embedded electronic lock will not prevent thieves from stealing your bike. Please use an additional mechanic lock during prolonged stops. ! Note: the embedded electronic lock drains a little energy from the battery. You can check the remaining energy on the lock screen of your smartph...
Page 20
20 4.5 performing a factory reset on bike+ all in one in order to perform a factory reset on your bike+ all in one, please swipe to the left the factory reset icon. The app will ask you to insert the pin of your bike to perform the factory reset. This procedure will reset the bike name, the bike pin...
Page 21
21 4.7 bike+ all in one power modes your bike+ all in one let you choose among different power modes. Each power mode has a different assistance factor and a different pedalling range. There are 7 available power modes: turbo, e-bike, range 1, range 2, range 3, bike+ and off. Here you can find a det...
Page 22
22 o e-bike: this power mode is a regular pedelec (or electric pedal assisted bicylce). The motor assistance is softer than the turbo mode and the maximum power is slightly lower than 250w. O range 1: this power mode is hybrid: bike+ helps you when you ride at lower speed and during accelerations, w...
Page 23
23 speed [km/h] 200 250 100 -100 0 0 5 10 15 20 25 30 motor power [w] pedalling effort regenerative zone figure 14: motor assistance / regenerative zone in range 1 mode figure 15: motor assistance / regenerative zone in range 2 mode speed [km/h] 200 250 100 -100 0 0 5 10 15 20 25 30 motor power [w] ...
Page 24
24 o range 3: this power mode is hybrid and it is sensitive to the road slope (see range 1). The motor assistance is softer than range 2 and the cutoff speed is limited, so your range can increase up to 90 km*. O bike+: this power mode is hybrid and it is sensitive to the road slope (see range 1). T...
Page 25
25 speed [km/h] 200 250 100 -100 0 0 5 10 15 20 25 30 motor power [w] batt er y l ev el pedalling effort batt er y tte ba baat te tter y ee regenerative zone figure 17: motor assistance / regenerative zone / battery level sensitivity in bike+ mode the default power mode is “turbo” (figure 12). 4.8 i...
Page 26
26 4.9 bike+ all in one warning icons warning icons let you understand when there is something wrong with your bike+ all in one functioning (see 4.1). If you experience a problem that prevent you from using your bike+ all in one correctly, please contact our customer care on our website or at info@z...
Page 27
27 battery warning this icon appears when there is a problem with the battery pack. Please contact us to have your battery pack fixed! Powertrain warning this icon appears when there is a problem with the electric powertrain. Please contact us to get the powertrain fixed! Warning icon tap on this ge...
Page 28
28 5. Notes on the battery pack the battery pack is protected against deep discharging, overcharging, overheating and short circuit through the battery management system (bms). In case of dangerous situ- ation an electronic protection will switch the battery pack off. Although the battery pack is pr...
Page 29
29 5.2 battery pack storage conditions bike+ all in one has to be stored at the right temperature. The battery pack life can be maximized by following the rules for a correct storage and handling. In case of malfunctioning your battery pack will have to be replaced. Please refer to a zehus retailer ...
Page 30
30 6. Technical data drive unit rated power w 250 maximum torque nm 20 battery pack rated voltage v 29.2 rated capacity mah 5300 energy wh 154.8 hub weight (~) kg 3.2 operating temperature °c -20°c to +70°c storage temperature °c -40°c to +60°c charging temperature °c -20°c to +60°c degree of protec...
Page 31
31 7. Maintenance and service ! Caution: every maintenance procedure (even cleaning bike+ all in one) must be done with the “bike” mode enabled. On the contrary, severe injury may occur. 7.1 cleaning bike+ all in one please, keep bike+ all in one hub clean. Clean it with a soft, damp cloth. Bike+ al...
Page 32
32 tape or mask off the 6-pin connector in such a manner that the connector itself cannot be damaged or broken. Inform your parcel service that the package contains danger- ous goods. Please also observe the possibility of more detailed national regulations. In case of questions concerning transport...
Page 34
Zehus srl via michele barozzi 6 20122 milano - italy phone: +390249434644 [sales], [info] @zehus.It www.Zehus.It doc number: 2016/01-rev2.00 the specifications on this document are subject to change at zehus de- cision. Zehus assumes no responsibility for any claims or damages arising out of the use...