Zenith Concierge H20E35DT Installation And Operating Manual, Warranty - Warning

Manual is about: TVs with FM Radio

Summary of Concierge H20E35DT

  • Page 2: Warning

    Record the model number the model and serial number of the concierge tm tv are located on the back of cabinet. For future reference, we suggest that you record these numbers here: model no.____________________________________ serial no.____________________________________ warning: to reduce the risk...

  • Page 3

    P a g e 3 206-3489-o 1. Read instructions all the safety and operating instructions should be read before the product is operated. 2. Follow instructions all operating and use instructions should be followed. 3. Retain instructions the safety and operating instructions should be retained for future ...

  • Page 4

    (continued from previous page) 14. Outdoor antenna grounding if an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the national electrical ...

  • Page 5

    206-3749 p a g e 5 table of contents turn to the next page to begin the tv set up purchase the optional installer’s remote and clone programmer to preform a normal installation set up, you need an installer’s remote like the lp702, and the lt2000 quickset ii clone programmer - - both are shown and d...

  • Page 6

    If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . Page 7 if you have cable and no other equipment, go to . . . . . . . . . . . . . . . . . . . Page 8 if you are using an antenna and have a vcr, go to . . . . . . . . . . . . . . . . . . Page 9 if you have cable and a...

  • Page 7

    Locate the antenna/cable jack on the back of the tv. Connect the antenna wire, according to one of the diagrams to the right. Remove the back of the remote and put in two aa batteries. Plug in the tv. The tv is designed to operate on stan- dard current, 120-volt 60 hertz ac. Do not attempt to operat...

  • Page 8

    206-3489-o p a g e 8 cable service (catv) hook up if you’re using a cable box, leave the tv on channel 3 or 4 and use your cable box to change channels. If you’re using a cable box, auto program might only find the channel your cable service is on (usually channel 3 or 4). Don’t worry, that’s all yo...

  • Page 9

    206-3489-o p a g e 9 antenna with vcr hook up connect an off-air antenna and vcr to the tv no a/v cables are included with the zenith tv. Without a/v cables, most vcrs will not play videocas- settes in stereo sound. Flat wire (300 ohm) antenna 300/75 ohm adapter a/v cables not included with tv in ou...

  • Page 10

    P a g e 1 0 206-3489-o cable service (catv) with vcr hook up connect a vcr and cable service to the tv leave the vcr and the television tuned to channel three and use the cable box to change channels. No a/v cables are included with your tv. Without a/v cables, most vcrs will not play videocassettes...

  • Page 11

    P a g e 1 1 206-3489-o external speaker hook up locate the audio in jack on the back of the speaker. Connect a standard audio cable from the matrix out jack on the tv, to the audio in jack on the external speaker. A/v cables not included with tv r- audio- l video in matrix out in audio in speaker ba...

  • Page 12: 3/5

    P a g e 1 2 206-3489-o auto program (channel search) use auto program to specify antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search with the installer remote control in hand, press the power key to turn on the tv. Press menu r...

  • Page 13

    P a g e 1 3 206-3489-o front panel controls audio video captions vol vol ch ch power in left right 1 4 press power to turn on your tv. To access the menus press the menu button on the control panel. Cycle through the various menus by pushing menu repeatedly. Press the select button repeatedly to hig...

  • Page 14

    P a g e 1 4 206-3488-o guest remote key functions flashbk (flashback) returns to the last channel viewed. Power turns tv on or off . Channel (up/down) chooses next available channel, and the video channel (audio/video source). Mute turns sound off and on, while the picture remains. Enter press to vi...

  • Page 15

    206-3489-o p a g e 1 5 installer remote key functions timer ch preview enter 1 2 3 4 5 6 7 8 9 0 power flshbk mute vol ume channel tv/fm cc menu alarm adj adj select flashbk (flashback) returns to the last channel viewed. Power turns tv on or off . Channel (up/down) selects next available channel an...

  • Page 16

    P a g e 1 6 206-3749 on-screen menus overview on-screen menus setup menu adjusts the basic operational features of the tv auto program 12 automatically finds and stores active channels to select with channel up/down. Add/del/blnk 19 manually picks and chooses which active channels will appear when u...

  • Page 17

    P a g e 1 7 206-3488-a other menus & on-screen displays ch 25 - pbs 7:15 old time movies length 01:00 time left 00:36 rating: tv-14 pm channel/time/audio/xds display press enter. Shows selected chan- nel or source, current time if the clock has been set, incoming audio signal, and xds info, if provi...

  • Page 18

    P a g e 1 8 selecting viewing sources make direct connections, or use the ch preview menu to choose the available picture and sound sources: either tunable channels or the aux source to appear on the tv screen a direct source connection overrides all other sources. The front video in jack is a direc...

  • Page 19: 3/5

    P a g e 1 9 206-3749 fine-tune the guest’s channel selection list setting add/delete/blank press the menu key on the installer’s remote so the setup menu appears. Press select repeatedly to highlight the add/del/blnk option. Using either the number keypad and enter or the channel up/down arrow on th...

  • Page 20

    P a g e 2 0 206-3600 channel labels auto program add/del/blnk ch. Labels clock set timer captions language ch 32 abc setup menu overview channel labels help the user identify the channel or network being viewed. In the setup menu with the ch labels option highlighted, use the adjust left/right arrow...

  • Page 21

    P a g e 2 1 206-3489-o clock set sets the tv’s internal clock timer ch preview enter 1 2 3 4 5 6 7 8 9 0 menu alarm adj adj select 3 5 4 4 mini glossary time a four-digit figure broken down into hours and minutes; first two digits are hours, last two digits are minutes. Hours first two digits that a...

  • Page 22: 3/5

    P a g e 2 2 206-3489-o setting on/off timers 1 2 3 4 5 timer ch preview enter 1 2 3 4 5 6 7 8 9 0 power flshbk mute vol ume channel tv/fm cc menu alarm adj adj select 2 on time 9:00 am off time 7:00 pm on/off timer on timer auto program add/del/blnk ch. Labels clock set timer captions language to se...

  • Page 23

    P a g e 2 3 206-3489-o captions (caption/text) timer ch preview enter 1 2 3 4 5 6 7 8 9 0 power flshbk mute vol ume channel tv/fm cc menu alarm adj adj select 1 standard closed captioning is available using the caption 1 option. Caption 1 caption 2 caption 3 caption 4 text 1 text 2 text 3 text 4 off...

  • Page 24

    P a g e 2 4 206-3240-o language auto program add/del/blnk ch. Labels clock set timer captions language english setup menu timer ch preview enter 1 2 3 4 5 6 7 8 9 0 power flshbk mute vol ume channel tv/fm cc menu alarm adj adj select 2 1 4 choose the language for the on-screen menus press the menu k...

  • Page 25: 2/4

    206-3488-a p a g e 2 5 mini glossary stereo sound stereo (stereophonic) sound refers to audio that’s divided into right and left sides. Mono sound mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. Soundrite maintains a constant volume leve...

  • Page 26

    P a g e 2 6 206-3488-a video menu press menu repeatedly until the video menu appears. Your options are: • contrast: adjusts the level of difference between white and black in the tv picture. The more contrast, the brighter the picture appears. • brightness: increases or decreases amount of white in ...

  • Page 27

    P a g e 2 7 206-3489-o note reset parental control block hours to zero and cancel password this provides the management staff and the installer a means to reset the tv to normal operation, if a guest has either forgotten the password or has left parental control block active after checking out. On t...

  • Page 28

    P a g e 2 8 206-3488-o installer parental control menu as shown above, with the parental control menu on-screen, use select to choose an option, like content block. Use the left/right adj arrow to show the content block menu, to adjust or set the rating for an option. For sex scenes for example, use...

  • Page 29

    P a g e 2 9 206-3488-o parental control menu unblocked blocked general children unblocked g and above pg and above pg-13 and above r and above nc-17 and above x dialog language sex scenes violence f violence no rating to block unblocked tv-pg and above tv-14 and above tv-ma unblocked tv-y7 unblocked...

  • Page 30

    P a g e 3 0 206-3488-o fm radio auto program use fm radio auto program to automatically store all of the fm stations that are found by the channel search with the installer remote control in hand, press power to turn on the tv. Press tv/fm to select fm operating mode on remote. Press menu repeatedly...

  • Page 31

    P a g e 3 1 206-3489-o fm radio on-screen menus overview fm setup menu options fm setup menu adjusts the basic features of the fm radio auto program automatically finds and stores all active fm radio stations within the range of 87.7 - 107.9. The user can then choose any fm radio station stored in m...

  • Page 32

    P a g e 3 2 206-3489-o fm radio audio menu mini glossary stereo sound stereo (stereophonic) sound refers to audio that’s divided into right and left sides. Mono sound mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. Adjust the fm radio au...

  • Page 33

    P a g e 3 3 206-3687-0 planning the channel banks generally, tv channels are grouped into “program pack- ages” with terms that are proposed to the end user. The user then opts for a package. Below is an example of how tv channels may be grouped. You may plan your package by using a chart like the on...

  • Page 34

    P a g e 3 4 206-3687-0 b purpose channel number a 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 n k 1 a a a a a a a a a a a a a a a 2 a a a a a a a a a a a a a a a 3 a a a a a a a a a a a a a a a 4 a a a a a a a a a a a a a a a b purpose channel number a 1 2 3 4 5 6 7 8 9 10 11 1...

  • Page 35

    P a g e 3 5 206-3687-0 plan your channel banks by filling in these charts (or use photocopies) b purpose channel number a 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 n k 1 2 3 4 b purpose channel number a 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 5...

  • Page 36

    P a g e 3 6 206-3749 installer menus installer should leave item 00 fact mode set to 0 (default). Items 25-92 are ser- vice-type adjustments and only qualified technicians having specialized test equip- ment should access them. Item description range fact. Set recommend. Setting 00 fact menu 0 - 1 1...

  • Page 37

    P a g e 3 7 206-3600-o installer menus 00 fact menu (factory mode) used to access and customize the 00 - 24 installer’s menu settings using installer type remotes. 01 preset px (preset picture) saves your custom video settings (color, tint, contrast, and bright- ness) in nonvolatile memory (not affe...

  • Page 38

    206-3600-o p a g e 3 8 installer menus the range of values is 0 - 255. Use (adjust) keys to choose num- bers that determine the start channel. 12 strt volume (start volume) when active, this function allows you to determine the initial vol- ume level setting when the tv is turned on. This feature is...

  • Page 39

    206-3600-o p a g e 3 9 a slow flashing green light indicates there is a problem with the communications between the tv and the programmer. In this case, check for a damaged cable, poor contacts, or other connection troubles. If the status indicator is red, the programmer batteries are low and should...

  • Page 40

    P a g e 4 0 206-3687-o lt2000 cloning procedures typical edit channel labels on-screen menus clone selection menu (1) learn from tv (2) teach to tv (3) set clone clock from tv (4) set tv clock from clone (5) display tv setup (6) display clone setup (7) edit channel labels (8) send channel labels -to...

  • Page 41

    P a g e 4 1 206-3687-o lt2000 cloning troubleshooting operation notes disconnect the clone from the tv when you are finished; auto- matically switching it off. The real-time clock continues to run when the main circuits are switched off. Reset clone after static shock after replacing exhausted batte...

  • Page 42

    P a g e 4 2 206-3749 routine tv cabinet and screen cleaning maintenance 1. Here’s a great way to keep the dust off the screen for a while. Wet a soft cloth in a mixture of luke- warm water and a little fabric softener or dish-washing detergent. Wring the cloth until it’s almost dry, and then use it ...

  • Page 43

    P a g e 4 3 206-3489-o symptoms snowy picture and unclear sound. Multiple images or ‘ghost shadows.’ interference: sharp lines across the screen and poor sound. Normal picture but no sound. No picture and unclear sound. No picture and no sound. No color, but the sound is o.K. Picture has a big black...

  • Page 44

    P a g e 4 4 206-3749 glossary a list of definitions for some of the words found in this installation and operating guide 75 ohm rf cable the wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto ...

  • Page 45

    P a g e 4 5 206-3488-o timer alarm ch preview enter 1 2 3 4 5 6 7 8 9 0 power flshbk mute vol ume channel tv/fm cc remote control part number sc692a 124-213-03a guest remote control key functions flashbk (flashback) return to the last channel viewed. Power turns tv on or off . Channel (up/down) scro...

  • Page 46

    P a g e 4 6 206-3749 guest parental control menu mini glossary motion picture association of america (mpaa) rating system g general audiences content not offensive to most viewers. Pg parental guidance content is such that parents may not want their children to view the program. Suggested pg-13 pare...

  • Page 47: 4/6

    P a g e 4 7 206-3488-o guest parental control menu mini glossary tv parental guideline rating system tv-g general audience considered suitable for all audiences; children may watch unattended. Tv-pg parental guidance suggested unsuitable for younger children, may contain: suggestive dialog, bad lang...

  • Page 48

    P a g e 4 8 206-3240-o guest menus & on-screen displays ch 25 - pbs 7:15 old time movies length 01:00 time left 00:36 rating: tv-14 pm channel/time/xds display press enter. Shows currently selected channel or source, current time if the clock has been set, incoming audio signal, and xds program info...

  • Page 49

    P a g e 4 9 206-3240-o guest fm radio operation timer alarm ch preview enter 1 2 3 4 5 6 7 8 9 0 power flshbk mute vol ume channel tv/fm cc flashbk (flashback) returns to the last fm radio station you were listening to. Power turns tv on or off . Channel (up/down) press to select next fm radio stati...

  • Page 50

    P a g e 5 0 206-3749 notes.

  • Page 51

    P a g e 5 1 206-3749 notes.

  • Page 52

    206-3749 issue* copyright 2002 zenith electronics corporation your zenith tv warranty for customer support/service please call: 1-888-865-3026 www.Zenith.Com direct-view color tv welcome to the zenith family! We believe that you will be pleased with your new zenith tv. Please read this warranty care...