Zenith H27G48S Service Manual - Installer Menu
INSTALLER MENU
3828VD0171G
2-2
DIGITAL FCS -
INSTALLER MENU
7-I. START VOLUME
This function allows the Installer to determine
the initial volume select that volume level when
it is turned on. The range of values are 0 - 63,
255. If 255 is selected, the current volume
level will be retained in memory when the TV is
turned off; at TV turn on, volume level is auto-
matically set to the previous or last level.
8-I. MIN VOLUME (Minimum Volume)
This function determines the minimum volume level
allowable with the VOLUME (VOL) Up/Down con-
trol. In this way, for example, someone cannot
set the sound too low to hear. The range is from
0 to 63—change values with ADJ (adjust). The
factory default is 0, which provides full range
of volume control. It may be best to set the
same value on every TV.
NOTE: The minimum volume level cannot have a
value setting higher than in the MAX VOLUME
level (described below).
9-I. MAX VOLUME (Maximum Volume)
This function determines the maximum volume level
allowable with the VOLUME Up/Down control. In
this way, for example, someone cannot set the
sound level high enough to disturb others.
The range is 0 to 63, with 63 as the default
which gives the user the full range of volume
control. Change values with ADJUST keys. It may
be best to set the same value on every TV.
NOTE: The maximum volume level cannot have a
value setting lower than the MIN VOLUME level
(described above).
10-I. MUTE DISABLE
Enables or disables sound mute function. If set
to 1, sound cannot be muted. If set to 0, sound
can be muted.
11-I. KEY DEFEAT (Keyboard Defeat)
When set to 1, it prevents the end user from
accessing screen menus with the front panel—
MENU, SELECT, and ADJUST do not function. When
set to 0, those keys are functional. The menus
can always be accessed with MENU on the remote.
12-I. NOT USED
13-I. NOT USED
14-I. NOT USED
15-I. SLEEP TIMER
When set to 1, the Sleep Timer feature is avail-
able to the user (but no message is displayed
prior to turn-off). When set to 0, the Sleep
Timer is not functional.
16-I. EN. TIMER (Enable Timer)
Set to 1, On/Off Timer functions are available
to user. Set to 0 to disable On/Off Timer func-
tions.
Note: Clock must be set in order to use Timers.
17-I. ALARM
Gives you the option of making the alarm func-
tion available to the user. Set to 1, Alarm
function is available to user. Set to 0 to dis-
able the Alarm function.
Note: Clock must be set in order to set the
Alarm.
18-I. NOT USED
19-I. NOT USED
20-I. FEATURE LEVEL
Default set to ZEN 1 for Zenith IR remote con-
trol operation. Set O, P LBL for Zenith Private
Label IR remote control operation.
Warning: Note: Installer should leave Item 20-I
FEATURE LEVEL set to 1 (default). Do not
set to “0” or remote will not control TV.
21-I. V-CHIP
Set to 1 to activate V-Chip (Parental Control);
have it available to user to filter or control
and restrict viewable program content. Set to 0
to turn V-Chip feature off, not available to
user; no programming
restrictions can be set.
22-I. MAX BLK HRS (Maximum Blocking Hours)
Set 0 to 99 for the maximum V-Chip (Parental
Control) block hours. Default setup is 12 block-
ing hours.
23-I. CAPTION LOCK
Set to 1 to restore previous Caption On/Off
state after TV turns off. When set to 0, Cap-
tions are always off, when TV is initially turned
on.
24-I. TEXT MODE
Determines whether TEXT 1, TEXT 2, TEXT 3, or
TEXT 4 decoding is enabled when TEXT is turned
on (either from the Setup Menu or directly with
CC on the remote).
TIP: Set Text Mode to 1 only if text is offered
in your video system.
25-I. FUNCTION PRE. (Function Preview)
Set to 0 to suppress CHANNEL PREVIEW from the
FUNCTION menu with some Pay-Per-View systems.
26-I. NOT USED
27-I. NOT USED
28-I. CH. OVERRIDE (Channel Override)
When set to 1, the user can select channels with
either CHANNEL Up/Down or by direct keypad en-
try. When set to 0, only those channels that are
entered for scanning may be selected by direct
keypad entry.