- DL manuals
- Zenith
- Monitor
- P42W22
- Owner's Manual
Zenith P42W22 Owner's Manual - Pc Mode Adjustments
24
3
2
1
Use the up/down button to select
SCREEN
and then press the vol (
G
) button.
Adjusting horizontal / vertical position manually
READY
Use the up/down button to select
V-POSI-
TION
or
H-POSITION
and then press the
vol (
G
) button.
• The adjustment range of
V-POSITION
is -50 ~ +50.
• The adjustment range of
H-POSITION
is -100 ~ +100.
• Based on the input mode, the adjustment range of
V-POSITION/H-POSITION
may change.
• Based on the VGA card, the adjustment range of
V-POSITION/H-POSITION
may
be out of -100 ~ +100 after auto configure.
• Based on the input signal, the position of the picture may not change even though
you have adjusted the horizontal or vertical positions.
Use the vol buttons to adjust to get the desired horizontal or
vertical position and then press the enter button to remove menus.
Press the menu button and then use the up/down button to
select the
SPECIAL
menu.
Press the vol (
G
) button.
LANGUAGE
G
CAPTION
G
AUTO OFF
G
SCREEN
G
RGB-OUTPUT
G
AUTO.CONFIG.
G
V-POSITION
G
H-POSITION
G
PHASE
G
RESET
G
0
V-POSITION
LANGUAGE
G
ARC
G
SCREEN
G
TRANSPARENCY
G
PIP
G
SET ID
G
COLOR TEMP.
G
G
TO SET
SPECIAL
SCREEN
- Only adjust
V-POSITION
and
H-POSITION
in DTV or component 480p/720p/1080i.
PC Mode Adjustments
menu
up
down
vol
up
down
vol
up
down
vol
enter
vol
vol
Summary of P42W22
Page 1
Plasma displa y p anel on/off input select volume p/no : 3828va0296l (nf01dc) plasma displa y p anel please read this operating guide carefully before using the monitor. Keep the operating guide with the monitor. For future reference, write down the serial number on the back of the monitor in the sp...
Page 2
On/off input select volume warning to reduce the risk of fire and electric shock, do not expose this prod- uct to rain or moisture. Power supply cord/appliance coupler is used as the main disconnect device, and as such shall be easily accessible after installation. Colored dots on the screen a pdp (...
Page 3: Table of Contents
Keep this manual with monitor for future easy reference table of contents first step warnings ..............................................................4 safety instructions........................................5 monitor overview front panel controls ..............................................
Page 4: Warnings
4 warnings warning: to reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside. Refer to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dan...
Page 5: Safety Instructions
5 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others important safeguards for you and your new product your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical sh...
Page 6: Safety Instructions
6 safety instructions the openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventila- tion is provided or the manufacturer’s instructions have bee...
Page 7
7 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. ...
Page 8: Front Panel Controls
8 front panel controls on/off on/off input select volume input select volume main power button input select button power standby indicator illuminates red in standby mode. Illuminates green when the monitor is turned on. Sub power button volume ( f f , g g ) buttons remote control sensor front panel...
Page 9: Connection Panel Overview
9 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others connection panel overview p y p (+) ( ) (+) ( ) ac input b r y (+) ( ) (+) ( ) p p component(480i/480p/720p/1080i) (dvd/dtv input) rgb-dtv input (480p/720p/1080i) b r rgb-pc input (...
Page 10
10 remote control key functions/accessories - when using the remote control aim it at the remote control sensor on the monitor. Power on mute 1 3 2 4 6 5 7 9 8 video/pc menu up down vol vol enter 0 sleep system off pip input select ratio freeze easy sound position apc power on button sleep button (r...
Page 11: Accessories
11 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others video/pc button on the remote control each press of this button changes the mode as shown below. S-video component video rgb as mark monitor 1.5v 1.5v accessories d-sub 15 pin cabl...
Page 12: Monitor Installation
12 monitor installation - it is recommended that this product only be used at an altitude of less than 6562 feet (2000m) to get the best quality picture and sound. - this plasma display is designed to be mounted horizontally (wide viewing). - your p42w22, p42w22b, p42w22h models (monitor) can be ins...
Page 13
13 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others desktop pedestal installation • the monitor can be mounted on a desk as shown above. (for further information, refer to the optional desktop stand installation and setup guide.) • ...
Page 14: Vcr Setup
14 vcr setup tip • to avoid picture noise (interference), leave an adequate distance (20 inches or more) between the vcr and monitor. S-video out in (r) audio (l) video back panel of vcr - as shown below, when connecting the monitor to a vcr, match the colors of av input jacks on the monitor with th...
Page 15: To Watch Vcr
15 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others p y p (+) ( ) (+) ( ) ac input b r y (+) ( ) (+) ( ) p p component(480i/480p/720p/1080i) (dvd/dtv input) rgb-dtv input (480p/720p/1080i) b r rgb-pc input (vga/svga/xga) external sp...
Page 16: Cable Tv Setup
16 cable tv setup - after subscribing to a cable tv service from a local provider and installing a converter, you can watch cable tv programming. This monitor cannot display tv programming without a tv tuner or cable tv converter box. Tv vcr rf cable (r) audio (l) video y (+) ( ) (+) ( ) external sp...
Page 17: External Av Source Setup
17 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others y (+) ( ) (+) ( ) external speaker(8 Ω ) r l r audio video (mono) l p p component(480i/480p/720p/1080i) (dvd/dtv input) b r rgb-dtv input rgb-pc input (vga/svga/xga) (480p/720p/108...
Page 18: Dvd Setup
18 dvd setup • connect dvd video outputs to y, p b , p r of component (480i/480p/720p/1080i) (dvd/dtv input) and audio inputs to audio jacks of av input. How to connect a dvd (digital video disk player) how to use • turn on the dvd player, and insert a dvd. • use the video/pc button on the monitor's...
Page 19: Dtv Setup
19 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others dtv setup - to watch digitally broadcast programs, purchase/connect a digital set-top box. - you can only use the 16:9 picture format in dtv 720p/1080i mode. How to connect a user-...
Page 20: Pc Setup
20 pc setup - show your computer’s image on the monitor. • turn the pc on and press on/off button on the monitor, to go to standby mode. Then press button on the monitor or press power on on the remote control. • use the video/pc button on the remote control to select the rgb source. • set the resol...
Page 21
21 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others tip • synchronization input form: signals are separate. Monitor display specifications 640x350 640x400 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66...
Page 22
22 3 2 pc mode feature check (overview) - use video/pc on remote to select rgb mode. - make sure the pc and monitor are both turned on. - use the monitor’s remote control to make adjustments. 1 press the menu button to show a menu on screen. Press the vol ( g ) button and then use the up/down or vol...
Page 23: Pc Mode Adjustments
23 safety instructions monitor overview basic operation sleep timer picture & sound special features others connections 1 3 pc mode adjustments use the up/down button to select screen and then press the vol ( g ) button. If picture needs to be adjusted more after auto adjustment, you can manually ad...
Page 24: Pc Mode Adjustments
24 3 2 1 use the up/down button to select screen and then press the vol ( g ) button. Adjusting horizontal / vertical position manually ready use the up/down button to select v-posi- tion or h-position and then press the vol ( g ) button. • the adjustment range of v-position is -50 ~ +50. • the adju...
Page 25
25 safety instructions monitor overview basic operation sleep timer picture & sound special features others connections 3 2 1 use the up/down button to select screen and then press the vol ( g ) button. Picture phase adjustments ready • if the picture isn’t clear after auto adjustment and especially...
Page 26
26 picture in picture (pip) function - pip lets you see 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - select rgb input source before pressing pip. - pip works in the following resolutions; 640x4...
Page 27
27 safety instructions monitor overview basic operation sleep timer picture & sound special features others connections selecting a source input signal press the input select button repeatedly in pip mode. • each time you press input select button, you toggle between video , s-video and component . ...
Page 28
28 3 2 1 use the up/down buttons to select pip and then press the vol ( g ) button. Ready use the up/down button to select sound select and then press the vol ( g ) button. • each time you press the up/down button, you toggle between sound [ m ] or sound [ s ]. Use the up/down buttons to select main...
Page 29: Remote Control Setup
29 safety instructions monitor overview basic operation sleep timer picture & sound special features others connections remote control setup installing batteries • open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match “+” with “+”,...
Page 30: Turning On The Monitor
30 turning on the monitor 3 2 1 2 1 - when using the remote control, aim it at its sensor on the monitor. Turning on the monitor just after installation turning on the monitor (power cord is still connected) plug power cord into power outlet correctly. Press the main on/off button on the monitor. At...
Page 31: Menu Language Selection
31 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others menu language selection 3 2 1 ready use the up/down button to select lan- guage and then press the vol ( g ) button. Use the up/down button to select the desired language. Press th...
Page 32: Checking Features
32 1 3 2 press the menu button. Press the up/down button. • each press will cycle through the menus shown below. Checking features use the vol ( g ) button to select menu option to adjust, and then use the up/down or vol buttons to adjust the selected option. • press the enter button to exit. Apc g ...
Page 33: Setting Sleep Timer
33 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others setting sleep timer sleep timer turns the monitor after the preset time expires use the sleep button to set a sleep time. Each time you press the sleep button, the time setting tim...
Page 34: Auto Picture Control
34 2 1 apc (auto picture control) press the apc button. Press the apc or vol buttons to select the picture appearance setup. • each press of vol buttons selects the menu option as shown below. • you can also select clear , soft or user in the pic- ture menu. User refers to adjustments made to the pi...
Page 35
35 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others 2 1 ready example : changing the contrast. Use the up/down button to select con- trast and then press the vol ( g ) button. • adjust brightness , color , tint and sharpness in the ...
Page 36
36 drp (digital reality picture) drp improves image outlines in dark screens. 3 1 ready use the up/down button to select drp and then press the vol ( g ) button. Press the enter button to exit. Apc g drp g contrast 100 g brightness 50 g color 50 g tint 0 g sharpness 50 g clear soft picture drp 2 use...
Page 37: Adjusting Sound
37 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others adjusting sound manual setting 2 1 ready example adjustment: treble use the up/down buttons to select treble and then press the vol ( g ) button. • adjust bass and balance in the s...
Page 38: Auto Sound Control
38 auto sound control dasp (digital auto sound processing) • this feature lets you enjoy the best sound without any manual adjustment. The monitor automatically selects the appropriate audio tone levels based on the program content. 1 press the easy sound button. 2 use the easy sound or vol buttons ...
Page 39: Avl (Auto Volume Leveler)
39 safety instructions monitor overview connections basic operation sleep timer special features others picture & sound avl (auto volume leveler) avl maintains a consistent volume level; even if you change channels. 3 1 ready use the up/down button to select avl and then press the vol ( g ) button. ...
Page 40: Using Still Function
40 using still function 1 2 press the freeze button. • the image displayed is frozen (stilled). • the sub picture is stilled in pip mode. • in pip mode, the sub (inset) picture is frozen. Moving image still (frozen) image to return to normal viewing, press the freeze button again. Tip • if a still p...
Page 41: Using The Screen Options
41 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others 3 2 1 ready use the up/down button to select screen and then press the vol ( g ) button. Use the up/down buttons to select tv or vcr . • select the vcr option if watching a vcr. • ...
Page 42: Adjusting Osd Transparency
42 adjusting osd transparency makes the menu backgrounds clear or opaque 3 2 1 ready use the up/down button to select transparency and then press the vol ( g ) button. Use the vol buttons to adjust osd transparency. • the transparency adjustment range is 1 ~ 4. Press the enter button to remove menu ...
Page 43
43 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others ready press the menu button and then press the up/down button to select the special menu. Press the vol ( g ) button. Color temperature adjustments 3 2 1 press the up/down button t...
Page 44: Setting Picture Format
44 setting picture format use the ratio button to select the desired picture format. • you can also select the 16:9 , 4:3 , or zoom option using the special menu. • each time you press ratio or vol buttons, you cycle through 16:9 , 4:3 , and zoom . Arc f 16 : 9 g 16:9 4:3 zoom arc f 4 : 3 g arc f zo...
Page 45
45 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others - connect the rs-232c input jack to an external control device (such as a computer or an a/v control system) and control the monitor’s functions externally. P y p (+) ( ) (+) ( ) a...
Page 46
46 external control device setup type of connector : d-sub 9-pin male * use a null modem cable. Wire the 7-wire cable so that each pair of data lines cross between the two devices. These data line pairs are rxd (receive data) and txd (transmit data), dtr (dte side ready) and dsr (dce side ready), an...
Page 47
47 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others 1 use the up/down buttons to select set id and then press the vol ( g ) button. • once set id is selected, use the vol button to choose a monitor id number. Set id ready press the ...
Page 48
48 external control device setup communication parameters command reference list - the rs-232c input jack is used to control the monitor’s functions using an external control device. • baud rate : 2400 bps (uart) • data length : 8 bits • parity : none • stop bit : 1 bit • communication code : ascii ...
Page 49
49 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others 01. Power (command:p) g to control power on/off of the monitor. Transmission data 0 : power off 1 : power on * example : power on for set id no.3. Type : p 3 1 ‘0x0d’ [p][ ][set id...
Page 50
50 external control device setup * real data mapping 0 : step 0 a : step 10 f : step 15 10 : step 16 64 : step 100 06. Volume control (command:v) g to adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission data min : 0 ~ max : 64 * refer to ‘real data mappi...
Page 51
51 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others 12. Osd select (command:d) g to select osd (on screen display) on/off. Transmission * the remote control and monitor front panel controls (except main power) are not operable when ...
Page 52
52 external control device setup * component source only works in 480i input signal. 16. Pip sound select (command:u) g to select main or sub (inset) sound for pip. You can also select sound select in pip on the special menu. Transmission [u][ ][set id][ ][data][cr] acknowledgement data 0 : main pic...
Page 53: Maintenance
53 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others maintenance cleaning the screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or ...
Page 54: Troubleshooting Checklist
54 no output from one of the speakers • adjust balance in the sound menu. (refer to p.37) • is speaker connected? Troubleshooting checklist no picture & no sound • check whether the monitor is turned on. • power cord inserted into wall power outlet? • plug another product’s power cord into the wall ...
Page 55: Product Specifications
55 safety instructions monitor overview connections basic operation sleep timer picture & sound special features others product specifications model width (inches / mm) height (inches / mm) depth (inches / mm) weight (pounds / kg) power requirement resolution color p42w22, p42w22b, p42w22h 41.6 / 10...
Page 56: Plasma
Plasma displa y p anel on/off input select volume p/no : 3828va0296l (nf01dc) plasma displa y p anel please read this operating guide carefully before using the monitor. Keep the operating guide with the monitor. For future reference, write down the serial number on the back of the monitor in the sp...