2 warning warning: to reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside. Refer to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dang...
Safety instructions safety instructions 3 safety instructions warning : to reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the ap...
4 safety instructions safety instructions continued safety instructions continued 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from t...
5 contents contens warnings....................................................................................................................2 safety instruction ·······································································································3-4 introducyion controls ·······...
6 introduction introduction introduction controls controls z15lcd1 z20lcd1 menu ch vol input menu ch vol input remote control sensor power/standby indic ator glows red in standby mode, glows green when the tv is turned on ..
7 introduction connection options connection options s-video h/p z15lcd1 power switch ac in rgb(pc) audio in headphone jack audio in s-video video in component in ant in z20lcd1 ac in for service on/off headphone jack audio in s-video video in component in ant in.
8 introduction - when using the remote control, aim it at the remote control sensor on the tv. • open the battery compartment cover on the back side and insert the batteries with correct polarity. • use two 1.5v batteries of aaa type. Don’t mix used batteries with new batteries. Installing batteries...
9 installation audio cable (pc) ( z15lcd1 only) owner’s manual aaa batteries remote control power cord d-sub cable (pc) ( z15lcd1 only) 3-fixing screw for stand installation installation accessories accessories ( z 20lcd1 only) © copyright 2005, lg electronics usa, inc. Installation and operating gu...
Note: here shown may be somewhat different from your set. 10 installation installation instruction installation instruction assembly the stand base installation instruction installation instruction 1. Connect the aerial cable to the socket marked ant in on the side. For the best reception an outdoor...
1 1 installation external equipment connections external equipment connections - for optimum picture quality, adjust antenna direction. - typical wall antenna jack used in apartment buildings, connect the antenna cable as shown below. (use the correct type of antenna cable for the type of wall anten...
Installation cable cable tv setup tv setup vcr setup vcr setup - in video mode, tv automatically reverts to tv mode if the input buttons are pressed. Connection 1 set vcr switch to 3 or 4 and then tune tv to the same channel number. Connection 2 1. Connect the audio/video output jacks on vcr to the ...
R audio v ideo l installation external external a/v source setup a/v source setup connections connect the audio/video output jacks on the external a/v equipment to the corresponding input jacks on the tv . When connecting the tv to external a/v equipment, match the jack colors (video = yellow, audio...
Installation dt v s etup dt v s etup - to watch digitally broadcast programs, purchase and con- nect a digital set-top box. C onnections c onnect the digital set-top box video outputs to the c om- p one nt (y, p b , p r ) jacks and connect the digital set-top box audio outputs to the audio jacks. (o...
Installation - after setup, be sure to select p c source on t v. P c s etup (15l c 1r p c s etup (z15l c d1 only) only) c onnections 1. Set the monitor output resolution on the pc before connecting to the tv. 2. Connect the t v to the p c with the p c cable. 3. Connect the p c audio output to the t ...
1 6 operation to use the menus 1. Press the menu button to display each menu 2. Use ▼,▲ to select a menu item. 3. Use ◀ ,▶ to enter a submenu or enable/disable the function. 4. Press the menu button to exit the menu. Main menu press the menu button to enter the main osd (on screen display). Adjust t...
1 7 operation sound menu options 1. The range of adjusting volume, bass : -05~+05, treble : -05~+05. 2. The range of adjusting balance is l40~r40; when adjusting from 0 to l40, the sound from the left track fades until silence; when adjusting from 0 to r40, the sound from the right track fades until...
18 operation picture menu options when the input source is in pc mode(only for z15lcd1) ,you can select brightness, contrast, position, video noise, sharpness, info, color temp., red, green, blue and reset to default; shown in the figure below: 1. Brightness and contrast: the range can be adjusted f...
1 9 operation when the input source is in component mode, you can select brightness, contrast, video noise ,color, sharpness, tint, temperature and reset to default respectively; shown in the figure below: 1. Brightness and contrast: the range can be adjusted from 0~100; use brightness and contrast ...
20 operation (1). Only when the child lock is on, and the channelock will be enabled; when the child lock setup is off, and the channelock is disabled. (2). Lock code: v-chip password can be set up when the code is locked. Enter the 4-digit password which you choose! The factory default password is ...
21 operation 2. Mpaa rating: select the movie ratings from low to high (alert) - g, pg, pg-13, r, nc-17, x and off. 3. Tv pg rating: shown in the figure below: the empty box refers to unlocked; the solid box refers to locked. 4. Reset to default: reset to the factory default value. Channel menu opti...
2 2 operation special menu options special menu options closed captions closed captions 2. An old, bad, or illegally recorded tape is being played. 3. Strong, random signals from a car or airplane interfere with the tv signal. 4. The signal from the antenna is weak. 5. The program wasn’t captioned w...
2 3 maintenance & product specifications maintenance & product specifications power requirement television system television channel television screen external antenna impedance audio output z15lcd1 * : ac100- 120v~ 50/60hz 1.0a z20lcd1 * : ac100- 120v~ 50/60hz 1.2a ntsc vhf : 2 ~ 13, uhf : 14 ~ 69,...
2 4 troubleshooting checklist t t roubleshooting checklist roubleshooting checklist the video function does not work. No picture & no sound no or poor color or poor picture • adjust color in menu option. • keep a sufficient distance between the product and the vcr. • try another channel. The problem...
2 5 troubleshooting checklist the audio function does not work. Picture ok & no sound • press the vol (or volume) button. • sound muted? Press mute button. • try another channel. The problem may be with the broadcast. • are the audio cables installed properly? Unusual sound from inside the product •...
2 6 note note note.
7 2 note note note.
Zenith electronics corporation lcd-tv limited warranty – usa zenith will repair or replace your product, at zenith’s option, if it proves to be defective in material or work- manship under normal use, during the warranty period (“warranty period”) listed below, effective from the date (“date of purc...