Summary of CDV4791
Page 1
Installation manual 2easy 1 user video entry kit.
Page 2
2 easy 1 user video entry kit 2.
Page 3
Camera lens night view led speaker nameplate call button microphone 90 mm 176 mm 23 mm bus pl s1+ s2+ s- 1 2 on 1 2 on mic adjustment lock control jumper doorstation code dip main connect port 1 2 3 spk adjustment rain cover 2 easy 1 user video entry kit cdv4791/2 2. 1: terminal descriptions 2 : cdv...
Page 4
160-165cm 1 2 1 2 3 4 2.2: installation & adjustments mounting without rain cover 2 easy 1 user video entry kit cdv4791/2 160-165cm 1 2 1 2 3 4 mounting with rain cover 4.
Page 5
Name label 1 2 on 4.3 fitting the name label from the rear of the metal section of the cdv91/92 unclip the plastic to open the transparent name plate, insert a name label and replace the plastic cover. 4.4 adjusting camera angle use a screwdriver to loosen the screw and adjust the angle of the camer...
Page 6
2 easy 1 user video entry kit cdv4791/2 the pc6a is a power/bus combiner unit, which is designed for the cdv 2easy 2 wire system to supply power for the external station, internal monitor and other accessories on the bus. It can operate as a normal power/bus combiner or auxiliary psu. The features a...
Page 7
2 easy 1 user video entry kit cdv4791/2 open the ac cover: 1. Push the cover base towards the centre with your fingers; 2. Lift up and pull out the cover. After connecting the ac cable, it is advised to replace the cover. Note: 1. The ac cable is not included in the package, it must comply to the sp...
Page 8
1 2 3 on bit dip1&2 reserved. Left to default. Set to off. When the monitor is in the middle of the line in daisy chain connection. Bit state description dip3 1 2 3 on 1 2 3 on press to display the camera view when in standby mode microphone transmits voice communication mounting hook to secure moni...
Page 9
1.Touch icon on main menu page. 2.Touch unlock button and hold for 2s. 3.A digital keypad will be shown. About local address 00.00 video standard auto system verson 00.01.00 display driver 1.0 front 1.0 ui 1.0 installer setup 123 _ touch the screen anywhere on monitor in standby mode, the main menu ...
Page 10
In default mode, when receive a calling the master and slave monitors will ring at the same time, however the master monitor will display the image while the slave monitors will not. This setting can be changed to allow all the slave monitors to display video from the panel at the same time when rec...
Page 11
Input no. User code input no. User code input no. User code 8201 code=1 8212 code=12 8223 code=23 8202 code=2 8213 code=13 8224 code=24 8203 code=3 8213 code=14 8225 code=25 8204 code=4 8215 code=15 8226 code=26 8205 code=5 8216 code=16 8227 code=27 8206 code=6 8217 code=17 8228 code=28 8207 code=7 ...
Page 12
B a c dps ps5 dbc4 monitor monitor monitor with two to four monitors f arthest monitor the maximum cable distance of the wiring is limited. Using different cables will also affect the maximum distance available from the 2easy system. 5: schematics & wiring 2 easy 1 user video entry kit cdv4791/2 12 ...
Page 13
1 2 5.2 basic wiring configurations - + monitor on l1 l2 pl s1+ s2+ s- monitor monitor monitor monitor 1 2 on id=00 'daisy cha in connection: 2 easy 1 user video entry kit cdv4791/2 13.
Page 14
Off on monitor monitor monitor monitor id=00 1 2 on a b c d impedance switch dip=on,off,off 85~260vac dps ps5 monitors l1 l2 pl s1+ s2+ s- l1 l2 pl s1+ s2+ s- l1 l2 pl s1+ s2+ s- l1 l2 pl s1+ s2+ s- 1 2 on 1 2 on 1 2 on 1 2 on 1# camera dip=on,off,off id=11 id=01 id=10 id=00 4# camera 3# camera 2# c...
Page 15
Eb * lock bus pl s1+ s2+ s- lock 2 nd 1 st 2 nd eb * 1 st eb * lock bus pl s1 + s2 + s- note: c onnecting one lock: connecting two locks: jumper position in 1 & 2 jumper position in 1 & 2 1. Electric locks must be power-on-to-unlock. 2. The door lock output is limited to 12v with holding current max...
Page 16
Lock bus pl s1 + s2 + s- take off the jumper power supply lock bus pl s1 + s2 + s- take off the jumper power supply lock note: 1. The external power supply must be rated according to the lock consumption. 2. The jumper must be removed before connecting. 3. Set up the unlock mode for the monitor for ...
Page 17
2 easy 1 user video entry kit cdv4791/2 input voltage: 100~240vac input frequency: 50~60hzrated output voltage: dc 28v+2v rated output current: 1.5a working temperature: -10 0 c~50 0 csw input voltage: max 230vac, 2a dimension: 140 x 90 x 60mm 17 1) all components should be protected from shock or v...
Page 18
2 easy 1 user video entry kit cdv4791/2 1) all components should be protected from shock or vibration, prevent impacts and sharp knocks. Do not drop 2) please clean with a soft cotton cloth, please do not use a chemical cleaning agent. If necessary, please use a little pure water or dilute soapy wat...