Www.2n.Cz version 2n ® helios ip automation door access intercom configuration manual 2.5.
The 2n telekomunikace joint-stock company is a czech manufacturer and supplier of telecommunications equipment. The product family developed by 2n telekomunikace a.S. Includes gsm gateways, private branch exchanges (pbx), and door and lift communicators. 2n telekomunikace a.S. Has been ranked among ...
Content 1. Terms and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. 2n® helios ip automation configuration . . . . . . . . . . . . . . . 5 3. Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. Actions . . . . . . . . . . . ...
4 2n telekomunikace a.S., www.2n.Cz ® 1. Terms and symbols symbols used in manual safety always abide by this information to prevent injury of persons. Warning always abide by this information to prevent damage to the device. Caution important information for system functionality. Tip useful advice ...
5 2n telekomunikace a.S., www.2n.Cz ® 2. 2n® helios ip automation configuration 2n helios ip ® provides flexible setting options depending on the user's requirements. If the standard setting options (switch/call settings, e.G.) are insufficient for the intended use, apply a special programmable inte...
6 2n telekomunikace a.S., www.2n.Cz ® the figure above shows a typical interconnection of the event, action and condition blocks. It holds true in general that an action is always tied with a selected event and is executed when a selected condition is met. The condition is optional and if none is se...
7 2n telekomunikace a.S., www.2n.Cz ® 2n helios ip ® allows up to 12 blocks to be created and interconnected (regardless of the block type - events, actions and conditions). Multiple actions can be assigned to an event or condition. Thus, you can create 6 actions and assign them to 6 events, or crea...
8 2n telekomunikace a.S., www.2n.Cz ® 3. Events 2n helios ip automation ® defines the following event types: keypressed – key pressed codeentered – numerical code entered cardentered – rfid card entered callstatechanged – call state changed inputchanged – digital input changed httptrigger – http com...
9 2n telekomunikace a.S., www.2n.Cz ® %1, , .., for quick dial buttons %2 %54 any for any button (default value). Separate the values with a comma while defining more keys than one. Suppresstones suppress sound signalling initiated by pressing of a non–programmed quick dial button. The parameter is ...
10 2n telekomunikace a.S., www.2n.Cz ® example event.Codeentered: code=12345 event.Cardentered the block defines the event generated by entering of the rfid card with cardentered the defined id (for rfid card reader models only). Parameters card define the rfid card id; refer to the card reader subs...
11 2n telekomunikace a.S., www.2n.Cz ® parameters state define the call state change. Valid values: ringing – ringing start connected – successful call connection terminated – call termination direction define the call direction. Valid values: incoming – incoming calls outgoing – outgoing calls any ...
12 2n telekomunikace a.S., www.2n.Cz ® input2 – digital input 2 cr_input1 – digital input 1 on card reader cr_input2 – digital input 2 on card reader there may be different lists of valid values for different models; refer 2n helios ip ® to the available digital inputs and outputs subsection. Edge d...
13 2n telekomunikace a.S., www.2n.Cz ® 100ms – 100 milliseconds example event generated 1s after the rise of event on row 1: event.Delay: startevent=1; delay=1s event.Timer the block defines the event generated with a defined delay after another timer specified event with a defined count of repetiti...
14 2n telekomunikace a.S., www.2n.Cz ® event.Timer: startevent=1; period=1s; count=3 event.Httptrigger the block defines the event generated by receiving of an http command httptrigger from the intercom http server. When the http command is received, an event will be generated whose id matches http:...
15 2n telekomunikace a.S., www.2n.Cz ® 4. Actions 2n helios ip automation ® defines the following types of actions: – activateswitch – switch activation setoutput – digital output state setting begincall – outgoing call setup answercall – incoming call answer endcall – call termination sendhttpreque...
16 2n telekomunikace a.S., www.2n.Cz ® example activate switch 1 if the event defined on row 2 arises and the condition defined on row 3 is met: action.Activateswitch: switch=1; event=2; condition=3 action.Setoutput the block defines the action necessary for setting of the intercom output to setoutp...
17 2n telekomunikace a.S., www.2n.Cz ® level define the required output level. This parameter is optional. Valid values: 0 – output deactivation 1 – output activation (default value) example activate output1 if the event defined on row 2 arises: action.Setoutput: output=output1; event=2 action.Begin...
18 2n telekomunikace a.S., www.2n.Cz ® action.Begincall: number=1001; event=2 action.Answercall the block defines the action necessary for answering of an incoming call. Answercall in case no call is coming or the incoming call is not ringing, the action will not initiate any activity. Parameters ev...
19 2n telekomunikace a.S., www.2n.Cz ® action.Sendhttprequest the block defines the action necessary for sending of an http sendhttprequest command to another lan device. The http command helps you control other devices in the lan (ip relay, recording system, another intercom, etc.). Parameters even...
20 2n telekomunikace a.S., www.2n.Cz ® 5. Conditions 2n helios ip automation ® defines the following types of conditions: profilestate – time profile state callstate – current call state inputstate – digital input state logicaland – logical and of conditions logicalor – logical or of conditions logi...
21 2n telekomunikace a.S., www.2n.Cz ® state define the required profile state. This parameter is optional. Valid values: active – active profile (default value) inactive – inactive profile example the condition is met for inactive time profile 1: condition.Profilestate: profile=1; state=inactive co...
22 2n telekomunikace a.S., www.2n.Cz ® example the condition is met for an inactive call: condition.Callstate: state=inactive condition.Inputstate the block defines the condition to be met in case the defined logic level inputstate gets connected to the defined digital input. Parameters input define...
23 2n telekomunikace a.S., www.2n.Cz ® condition.Logicaland the block helps you create groups of conditions. The block is fulfilled if all logicaland the conditions in the defined group are met. Parameters condition define the list of conditions to be met. Separate the conditions with a comma. Examp...
24 2n telekomunikace a.S., www.2n.Cz ® define the condition not to be met. Example the condition is met in case condition 1 is not met: condition.Logicalnot: condition=1 condition.True the block defines the condition to be met each time. True parameters there are no parameters in the true block. Exa...
25 2n telekomunikace a.S., www.2n.Cz ® parameters clockevent define the event at which the current state of the condition is to be recorded. Condition define the condition to be recorded at the rise of the clockevent. Resetvalue set the condition default value upon restart. The parameter is optional...
26 2n telekomunikace a.S., www.2n.Cz ® 1 – condition is met example the condition will be met at the rise of event 1 and not met at the rise of event 2: condition.Flipfloprs: setevent=1; resetevent=2.
27 2n telekomunikace a.S., www.2n.Cz ® 6. Available digital inputs and outputs in this section, the digital inputs and outputs available on each model 2n helios ip ® are described. 2n helios ip vario ® outputs relay1 – relay output on basic unit relay2 – relay output on additional switch (if install...
28 2n telekomunikace a.S., www.2n.Cz ® relay2 – relay output on additional switch (if installed) output2 – digital 12v output on additional switch (if installed) cr_relay1 – relay output on card reader (if installed) cr_output1 – digital 12v output on card reader (if installed) redled – red led indi...
29 2n telekomunikace a.S., www.2n.Cz ® 7. Examples of use calling to dispatching office in case of unauthorised door opening specification call the selected telephone number whenever the tamper switch is disconnected (device opened). Block diagram the rising edge on the tamper input (1: event.Inputc...
30 2n telekomunikace a.S., www.2n.Cz ® block diagram the rising edge on the tamper input (1: event.Inputchanged) initiates calling to the defined telephone number (5: action.Begincall) in case the defined condition is met. The condition (4: condition.Flipfloprs) is validated by the intercom restart ...
31 2n telekomunikace a.S., www.2n.Cz ® intercom settings 1: event.Cardentered: card=0*0000 2: action.Activateswitch: switch=1; event=1 alarm (dispatching office call) caused by over 2-min long door opening specification call the dispatching office in case the door remains open for more than 2 minute...
32 2n telekomunikace a.S., www.2n.Cz ® led flashing during call / electric door lock opening specification enable led flashing during an active call. Block diagram enable led flashing by a combination of the periodic timer (1: event.Timer) and delay (2: event.Delay). These two blocks define the peri...
33 2n telekomunikace a.S., www.2n.Cz ® 2n telekomunikace a.S. Modřanská 621, 143 01 prague 4, czech republic tel.: +420 261 301 500, fax: +420 261 301 599 e-mail: sales@2n.Cz web: www.2n.Cz xxxx.