3Com 3C13701 Quick Reference Manual

Other manuals for 3C13701: Installation Manual, Module Manual
Manual is about: Router 5000 Family and Router 6000 Family

Summary of 3C13701

  • Page 1

    Copyright © 2006, 2007 3com corporation. All rights reserved. Www.3com.Com part number: 10016467 rev. Aa published: october 2007 3c om r outer 5000/6000 f amily q uick r eference g uide overview this command reference applies to the following router 5000/6000 models running software version 3.0. Abo...

  • Page 2

    2 3com router 5000/6000 family command reference displaying command parameters at the prompt, enter the name of the command followed by a space and ? . For example: router5000 -xx> boot ? The following parameters are displayed: attribute-switch exchange the file main-attribute and backup-attribute. ...

  • Page 3

    3com router 5000/6000 family 3 command reference abr-summary use the abr-summary command to configure the route aggregation on the area border router (abr). Ospf area view access-limit use the access-limit command to configure a limit to the amount of supplicants in the current isp domain. Isp domai...

  • Page 4

    4 3com router 5000/6000 family command reference address use the address command to configure a route to the peer voice gateway or assign an x.121 address for a destination host. Voice entity view address sip use the address sip command to set routing policy for reaching the remote voice gateway (vg...

  • Page 5

    3com router 5000/6000 family 5 command reference ani-offset use the ani-offset command to configure the number of digits of the called number to be collected prior to requesting the calling party information. R2 cas view answer use the answer command to configure whether the terminating point is req...

  • Page 6

    6 3com router 5000/6000 family command reference apply origin use the apply origin command to set the routing source of bgp routing information. Routing policy view apply output-interface (for multicast policy routing) use the apply output-interface command to configure an outgoing interface list in...

  • Page 7

    3com router 5000/6000 family 7 command reference arp timer aging use the arp timer aging command to set the aging timer for dynamic arp entries. System view asbr-summary use the asbr-summary command to configure summarization of redistributed routes by ospf. Ospf view ascii use the ascii command to ...

  • Page 8

    8 3com router 5000/6000 family command reference authentication use the authentication command to enable user authentication and authorization for the access service number. Voice access-number view authentication use the authentication command to set the ip address, port number and shared key for t...

  • Page 9

    3com router 5000/6000 family 9 command reference balance use the balance command to configure the number of routes participating in bgp load balancing. Bgp view band-based-sharing use the band-based-sharing command to enable bandwidth-based unbalanced load sharing. System view baudrate use the baudr...

  • Page 10

    10 3com router 5000/6000 family command reference binary use the binary command to set data type to binary for file transfer. Ftp client view boot bootrom use the boot bootrom command to upgrade bootrom. System view boot bootrom use the boot bootrom command to upgrade bootrom. System view bootfile b...

  • Page 11

    3com router 5000/6000 family 11 command reference bridge-set stp enable use the bridge-set stp enable command to disable stp on the port. Interface view bridge-set stp port pathcost use the bridge-set stp port pathcost command to configure the path cost of the bridge port. Interface view bridge-set ...

  • Page 12

    12 3com router 5000/6000 family command reference ca identifier use the ca identifier command to specify the ca this device trusts and have the "name" ca bound with this device. Pki domain view cable use the cable command to set the cable length matching the ce1/pri interface. Ce1/pri interface view...

  • Page 13

    3com router 5000/6000 family 13 command reference cd use the cd command to change the current working directory of the user to the specified directory. User view cd use the cd command to change the current working directory path on the remote ftp server. Ftp client view cdr use the cdr command to co...

  • Page 14

    14 3com router 5000/6000 family command reference cid enable use the cid enable command to enable cid on the fxo interface. Voice subscriber-line view cid select-mode use the cid select-mode command to configure the route selection mode used by the calling party to set up vofr calls. Dlci view cid s...

  • Page 15

    3com router 5000/6000 family 15 command reference clock use the clock command to set the clock mode of atm e3/t3 interface. Atm e3/t3 interface view. Clock use the clock command to set the clock mode on an atm interface. Atm interface view clock use the clock command to specify atm interface to use ...

  • Page 16

    16 3com router 5000/6000 family command reference code nrzi use the code nrzi command to set the digital signal coding format to none-return-to-zero-inverse (nrzi) for a synchronous serial interface. Synchronous serial interface view code nrzi use the code nrzi command to configure the nrzi encoding...

  • Page 17

    3com router 5000/6000 family 17 command reference controller cpos use the controller cpos command to enter cpos interface view. System view controller e1 use the controller e1 command to enter ce1/pri interface view. System view controller e3 use the controller e3 command to enter the ce3 interface ...

  • Page 18

    18 3com router 5000/6000 family command reference crl update-period use the crl update-period command to specify the update period of crl, which is the interval between local downloads of crls from crl access server. Pki domain view crl url use the crl url command to specify the distribution point u...

  • Page 19

    3com router 5000/6000 family 19 command reference ddns refresh use the ddns refresh command to request the ddns service provider to notify the dns server that the bound ip address of the domain name specified by the ddns domainname command has changed. Ddns configuration view ddns server use the ddn...

  • Page 20

    20 3com router 5000/6000 family command reference debugging clns echo use the debugging clns echo command to enable debugging for echo packets. User view debugging clns rd use the debugging clns rd command to enable debugging for rd packets. User view debugging clns routing use the debugging clns ro...

  • Page 21

    3com router 5000/6000 family 21 command reference debugging esis use the debugging esis event command to enable debugging for es-is protocol-related events. You can display event information using this command, such as changes of neighbor states, entries in level 0 routing table, and interface state...

  • Page 22

    22 3com router 5000/6000 family command reference debugging ipsec use the debugging ipsec command to turn ipsec debugging on. User view debugging ipx packet use the debugging ipx packet command to enable ipx packet debugging switch to view the contents of ipx packet received and transmitted. User vi...

  • Page 23

    3com router 5000/6000 family 23 command reference debugging mobile-ip advertise use the debugging mobile-ip advertise command to enable debugging for mobility agent advertisements. User view debugging mobile-ip mobile-router use the debugging mobile-ip mobile-route command to enable debugging for an...

  • Page 24

    24 3com router 5000/6000 family command reference debugging pim sm use the debugging pim sm command to enable pim-sm debugging functions. User view debugging pki use the debugging pki command to enable pki debugging functions. Any view debugging portal use the debugging porta l command to enable por...

  • Page 25

    3com router 5000/6000 family 25 command reference debugging rlogin use the debugging rlogin command to enable remote login (rlogin) debugging. User view debugging rsh use the debugging rsh command to enable rsh debugging. User view debugging sdlc use the debugging sdlc command to enable the sdlc deb...

  • Page 26

    26 3com router 5000/6000 family command reference debugging voice data-flow use the debugging voice data-flow command to enable debugging for voice data processes. User view debugging voice dpl use the debugging voice dpl command to enable the debugging of voice dial program. User view debugging voi...

  • Page 27

    3com router 5000/6000 family 27 command reference debugging voice vofr use the debugging voice vofr command to enable vofr module debugging. User view debugging voice vpp use the debugging voice vpp command to enable the debugging of the vpp module. User view debugging voice vpp r2 use the debugging...

  • Page 28

    28 3com router 5000/6000 family command reference default entity modem compatible-param use the default entity modem compatible-param command in the case that you fail to use standard modem pcm to interoperate with devices from other vendors. Voice dial program view default entity modem protocol use...

  • Page 29

    3com router 5000/6000 family 29 command reference default tag use the default tag command to configure the default tag of ospf when it redistributes an external route. Ospf view default type use the default type command to configure the default type when ospf redistributes external routes. Ospf view...

  • Page 30

    30 3com router 5000/6000 family command reference destination-ip use the destination-ip command to configure the destination ip address in the test. Hwping test group view destination-port use the destination-port command to configure the destination port in the test. Hwping test group view detect u...

  • Page 31

    3com router 5000/6000 family 31 command reference dhcp server bims-server (interface view) use the dhcp server bims-server command to enable and configure bims option support on the current interface. Ethernet interface (or subinterface) view dhcp server bims-server interface (system view) use the d...

  • Page 32

    32 3com router 5000/6000 family command reference dhcp server option (interface view) use the dhcp server option command in interface view to configure a dhcp self-defined option for the dhcp address pool of the current interface. Ethernet interface (or subinterface) view dhcp server option interfac...

  • Page 33

    3com router 5000/6000 family 33 command reference dialer disconnect use the dialer disconnect command to clear the dial-up link or the session link on the specified interface at the pppoe/pppoa client. Any view dialer enable-circular use the dialer enable-circular command to enable circular dcc. Phy...

  • Page 34

    34 3com router 5000/6000 family command reference dialer timer wait-carrier use the dialer timer wait-carrier command to configure the timeout time of wait-carrier timer. Physical or dialer interface view dialer timer warmup use the dialer timer warmup command to set the length of the warmup timer o...

  • Page 35

    3com router 5000/6000 family 35 command reference display aspf all use the display aspf all command to view the information of all aspf policies and sessions. Any view display aspf interface use the display aspf interface command to view the interface configuration of the inspection policy. Any view...

  • Page 36

    36 3com router 5000/6000 family command reference display bgp multicast routing as-path-acl use the display bgp multicast routing as-path-acl command to view in the bgp routing table the mbgp routes that match the specified as path list. Any view display bgp multicast routing cidr use the display bg...

  • Page 37

    3com router 5000/6000 family 37 command reference display bgp routing community use the display bgp routing community command to view the routing information related to the specified bgp community number in the routing table. Any view display bgp routing community-list use the display bgp routing co...

  • Page 38

    38 3com router 5000/6000 family command reference display bridge spanning tree use the display bridge spanning-tree command to view stp state and statistics for traffic analysis and control. Any view display bridge traffic use the display bridge traffic command to view the traffic statistics on an i...

  • Page 39

    3com router 5000/6000 family 39 command reference display controller cpos e1 use the display controller cpos e1 command to view the physical layer configuration information of a specified e1 channel on the specified cpos interface. Any view display controller cpos t1 use the display controller cpos ...

  • Page 40

    40 3com router 5000/6000 family command reference display dhcp relay statistics use the display dhcp relay statistics command to view the statistics of dhcp relay in packet errors, dhcp packets received from clients, dhcp packets received from and sent to servers, and dhcp packets sent to clients (i...

  • Page 41

    3com router 5000/6000 family 41 command reference display dlsw reachable-cache use the display dlsw reachable-cache command to view the reachable-cache of dlsw. Any view display dlsw remote use the display dlsw remote command to view the information of the remote peers. Any view display dlsw remote ...

  • Page 42

    42 3com router 5000/6000 family command reference display encrypt-card fast-switch use the display encrypt-card fast-switch command to view the entries in the fast forwarding cache for the encryption cards. Any view display encrypt-card sa use the display encrypt-card sa command to view sa informati...

  • Page 43

    3com router 5000/6000 family 43 command reference display fib longer use the display fib longer command to display the fib table entries matching the destination address. Different parameters selected leads to different matching methods. Use the display fib command to display the fib table entries w...

  • Page 44

    44 3com router 5000/6000 family command reference display fr pvc-infoc use the display fr pvc-info command to view the frame relay pvc table. Any view display fr statistics use the display fr statistics command to view the current frame relay statistics about receiving and sending packets. Any view ...

  • Page 45

    3com router 5000/6000 family 45 command reference display ike dpd use the display ike dpd command to display the configuration of the specified or all dpd structures about reference count, interval-time, and time_out. Any view display ike peer use the display ike peer command to view the configurati...

  • Page 46

    46 3com router 5000/6000 family command reference display interface null use the display interface null command to view the state about the null interface. Any view display interface pos use the display interface pos command to view the configuration and state information of one or all pos interface...

  • Page 47

    3com router 5000/6000 family 47 command reference display ip policy use the display ip policy command to view the routing policies of local and configured interface policy routings. Any view display ip policy setup use the display ip policy setup command to view the setting information of policy rou...

  • Page 48

    48 3com router 5000/6000 family command reference display ip vpn-instance use the display ip vpn-instance command to view the information related to vpn-instance, such as rd, description, and interfaces of the vpn instance. Any view display ipsec policy use the display ipsec policy command to view i...

  • Page 49

    3com router 5000/6000 family 49 command reference display isdn parameters use the display isdn parameters command to view the system parameters at layers 2 and 3 of the isdn protocol, such as the durations of system timers and frame size. Any view display isdn spid use the display isdn spid command ...

  • Page 50

    50 3com router 5000/6000 family command reference display mac-address use the display mac-address command to display information about mac address entries of an interface or about all mac address entries. Any view display memory use the display memory command to view information on system memory loa...

  • Page 51

    3com router 5000/6000 family 51 command reference display mobile-ip visitor use the display mobile-ip visitor command to display information in the visitor table and pending table of an fa. An fa updates its visitor table and pending table based on registration events of mns. If not specify the ip-a...

  • Page 52

    52 3com router 5000/6000 family command reference display msdp sa-cache use the display msdp sa-cache command to view (s, g) state learnt from msdp peer. Any view display msdp sa-count use the display msdp sa-count command to view the number of sources and groups in msdp cache. Any view display mult...

  • Page 53

    3com router 5000/6000 family 53 command reference display ospf cumulative use the display ospf cumulative command to view the ospf cumulative information. Any view display ospf error use the display ospf error command to view the statistics of error information which ospf received. Any view display ...

  • Page 54

    54 3com router 5000/6000 family command reference display pki crl use the display pki crl command to display and browse through the locally saved crl. Any view display port use the display port command to check whether the current system has hybrid or trunk ports. If there is any, its port name is d...

  • Page 55

    3com router 5000/6000 family 55 command reference display qos cq interface use the display qos cq interface command to view configuration and statistics of customized queues (cq) at interfaces. Any view display qos cql use the display qos cql command to view contents of customized queue lists (cpl)....

  • Page 56

    56 3com router 5000/6000 family command reference display rip interface use the display rip interface command to display information about the specified rip interface or all rip interface. Any view display rip routing use the display rip routing command to display the rip routing table, including no...

  • Page 57

    3com router 5000/6000 family 57 command reference display snmp-agent community use the display snmp-agent community command to view information on the configured communities of snmpv1 or snmpv2. Any view display snmp-agent group use the display snmp-agent group command to view information about the ...

  • Page 58

    58 3com router 5000/6000 family command reference display status interface use the display status interface command to display the state of the specified interface. Any view display status interface ima-group use the display status interface ima-group command to view detailed information about the s...

  • Page 59

    3com router 5000/6000 family 59 command reference display user-interface use the display user-interface command to view information about the specified or all user interfaces. Any view display users use the display users command to view the login information of the users on each user interface. Any ...

  • Page 60

    60 3com router 5000/6000 family command reference display voice entity use the display voice entity command to view the configuration information of voice entities of different types. Any view display voice fax use the display voice fax command to view the fax statistics in the fax module and the st...

  • Page 61

    3com router 5000/6000 family 61 command reference display voice voip data-statistic use the display voice voip data-statistic command to view statistics information of voice data. Any view display voice vpp use the display voice vpp command to view all the statistic information in the vpp module. An...

  • Page 62

    62 3com router 5000/6000 family command reference display x25 x2t switch-table use the display x25 x2t switch-table command to display the dynamic switching routing table and static routing table. Any view display x25 xot use the display x25 xot command to view xot link information. Any view dl-bits...

  • Page 63

    3com router 5000/6000 family 63 command reference dlsw remote use the dlsw remote command to create a remote dlsw peer and specifies its version and filtering rule. System view dlsw reverse use the dlsw reverse command to convert a mac address from ethernet order to token ring order or vice versa. S...

  • Page 64

    64 3com router 5000/6000 family command reference dtmf threshold use the dtmf threshold command to configure the sensitivity of dtmf digit detection. Voice subscriber-line view duplex use the duplex command to set the operating mode of the ethernet interface. Ethernet interface view duplex use the d...

  • Page 65

    3com router 5000/6000 family 65 command reference dvpn service use the dvpn service enable command to enable dvpn on a device. System view e1 bert use the e1 bert command to set test error bit for line bit on ce3 interface. Ce3 interface view e1 channel-set use the e1 channel-set command to bundle t...

  • Page 66

    66 3com router 5000/6000 family command reference em-phy-parm use the em-phy-parm command to configure a wire scheme for the analog e&m subscriber-line. Voice subscriber-line view em-signal use the em-signal command to configure a voice subscriber-line start mode. Voice subscriber-line view enable u...

  • Page 67

    3com router 5000/6000 family 67 command reference esp encryption-algorithm use the esp encryption-algorithm command to set the encryption algorithm adopted by esp. Ipsec proposal view exchange-mode use the exchange-mode command to select an ike negotiation mode. Ike-peer view execute use the execute...

  • Page 68

    68 3com router 5000/6000 family command reference fe1 detect-ais (e1-f interface) use the fe1 detect-ais command to enable alarm indication signal (ais) detect on the e1-f interface. E1-f interface view fe1 frame-format use the fe1 frame-format command to configure the framing format of the e1-f int...

  • Page 69

    3com router 5000/6000 family 69 command reference filter-policy import use the filter-policy gateway import command to filter the learned routing information advertised by the specified address. Use the filter-policy import command to filter the received global routing information. Bgp unicast view ...

  • Page 70

    70 3com router 5000/6000 family command reference flag use the flag command to set the overhead byte of sonet/sdh frames. Cpos interface view flag use the flag command to set the sdh overhead byte. Pos interface view flow control use the flow-control command to enable flow control on the ethernet in...

  • Page 71

    3com router 5000/6000 family 71 command reference fr congestion-threshold use the fr congestion-threshold command to enable congestion management function of a frame relay interface. Frame relay interface view mfr interface view fr de del use the fr de del command to apply a de rule list to the spec...

  • Page 72

    72 3com router 5000/6000 family command reference fr lmi t392dce use the fr lmi t392dce command to set t392 parameter at the dce side. Interface view fr lmi type use the fr lmi type command to configure the frame relay lmi protocol type. Interface view fr map bridge use the fr map bridge command to ...

  • Page 73

    3com router 5000/6000 family 73 command reference fragment use the fragment command to enable the frf.12-compliant fragmentation function on frame relay virtual circuit. Frame relay class view frame-format use the frame-format command to set the frame format of atm oc-3c/stm-1 interface. Atm interfa...

  • Page 74

    74 3com router 5000/6000 family command reference ft1 clock use the ft1 clock command to configure clocking on the t1-f interface. T1-f interface view ft1 code use the ft1 code command to configure line code format for a t1-f interface. T1-f interface view ft1 data-coding use the ft1 data-coding nor...

  • Page 75

    3com router 5000/6000 family 75 command reference ftp timeout use the ftp timeout command to set the idle-timeout timer. System view ftp update use the ftp update command to set the file update mode that the ftp server uses while receiving data. System view fxo-monitoring use the fxo-monitoring enab...

  • Page 76

    76 3com router 5000/6000 family command reference group use the group command to create a peer group. Bgp view group-b use the group-b command to enable or disable group-b stage signal to complete register exchange. R2 cas view gts use the gts command to configure traffic shaping for a behavior. Tra...

  • Page 77

    3com router 5000/6000 family 77 command reference hwatacacs change-password self use the hwtacacs change-password self command to enable the tacacs online user to change the password. User view hwatacacs nas-ip use the hwtacacs nas-ip command to specify the source address of the hwtacacs packet sent...

  • Page 78

    78 3com router 5000/6000 family command reference if-match acl use the if-match acl command to set the match condition for ip address. Route-policy view if-match acl use the if-match acl command to configure the ip address range to match the route-policy. Routing policy view if-match any use the if-...

  • Page 79

    3com router 5000/6000 family 79 command reference if-match mpls-exp use the if-match mpls-exp command to configure the matching rule for exp domain of mpls. Class view if-match mpls-label use the if-match mpls-label command to configure to match public network routes with mpls labels only. Route-pol...

  • Page 80

    80 3com router 5000/6000 family command reference igmp timer other-querier-present use the igmp timer other-querier-present command to configure the overtime value of presence of igmp querier. Interface view igmp timer query use the igmp timer query command to configure the interval at which a route...

  • Page 81

    3com router 5000/6000 family 81 command reference impedance use the impedance command to configure the current electric impedance on a voice subscriber-line. Fxo voice subscriber-line view import-route use the import-route command to redistribute routes from other protocols. Bgp view import-route us...

  • Page 82

    82 3com router 5000/6000 family command reference info-center monitor channel use the info-center monitor channel command to have the info-center output information over the specified channel to the user terminal. System view info-center snmp channel use the info-center snmp channel command to set t...

  • Page 83

    3com router 5000/6000 family 83 command reference interface loopback use the interface loopback command to create a loopback interface or its view. System view interface mfr use the interface mfr command to create a multilink frame relay bundle interface or sub-interface and enter the corresponding ...

  • Page 84

    84 3com router 5000/6000 family command reference ip address ppp-negotiate use the ip address ppp-negotiate command to allow ip address be assigned through negotiation at the interface. Interface view ip address unnumbered use the ip address unnumbered command to enable an interface to borrow the ip...

  • Page 85

    3com router 5000/6000 family 85 command reference ip fast-forwarding use the ip fast-forwarding command to enable unicast fast packet forwarding on both inbound and outbound interfaces. Use the ip fast-forwarding inbound command to enable unicast fast packet forwarding on the inbound interface. Use ...

  • Page 86

    86 3com router 5000/6000 family command reference ip netstream timeout inactive use the ip netstream timeout inactive command to set the inactive aging timer for netstream cache entries. System view ip option source-routing use the ip option source-routing command to enable ip source routing, allowi...

  • Page 87

    3com router 5000/6000 family 87 command reference ip vpn-instance use the ip vpn-instance command to create and configure a vpn-instance. Use the ip vpn-instance command to create a vpn-instance named vpn-name. System view routing protocol (bgp and rip) view ipsec card-proposal use the ipsec card-pr...

  • Page 88

    88 3com router 5000/6000 family command reference ipx netbios-propagation use the ipx netbios-propagation command to configure the router to forward type 20 broadcast packets on the current interface. Interface view ipx network use the ipx network command to configure a network id for an interface. ...

  • Page 89

    3com router 5000/6000 family 89 command reference ipx split-horizon use the ipx split-horizon command to enable split horizon on the current interface. Interface view ipx tick use the ipx tick command to configure the delay of interface sending ipx packets. Interface view ipx update-change-only use ...

  • Page 90

    90 3com router 5000/6000 family command reference isdn number-property use the isdn number-property command to set the type and code scheme of calling or called numbers in incoming or outgoing isdn calls. Isdn interface view isdn overlap-sending use the isdn overlap-sending command to set the system...

  • Page 91

    3com router 5000/6000 family 91 command reference isdn statistics use the isdn statistics command to have the system make statistics on the information received and transmitted at an isdn interface. Use the isdn statistics start command in the view of an interface to start making statistics on the m...

  • Page 92

    92 3com router 5000/6000 family command reference isis timer lsp use the isis timer lsp command to configure minimum is-is lsp interval on the interface. Interface view isis timer retransmit use the isis timer retransmit command to configure the lsp retransmission interval over the point-to-point li...

  • Page 93

    3com router 5000/6000 family 93 command reference limit use the limit command to create rule under corresponding connection limit policy. Connection limit policy view line use the line command to associate the voice entity with a specified voice subscriber-line. Pots voice entity view line use the l...

  • Page 94

    94 3com router 5000/6000 family command reference llc2 receive-window use the llc2 receive-window command to configure the maximum packets that can be sent before the llc2 receives the acknowledgement frame. Ethernet interface view llc2 timer ack use the llc2 timer ack command to configure the llc2 ...

  • Page 95

    3com router 5000/6000 family 95 command reference log-peer-change use the log-peer-change command to turn on the ospf adjacency changes output switch for the current ospf process. Ospf view log startup use the log startup command to turn on the configuration restoration log switch. User view loopbac...

  • Page 96

    96 3com router 5000/6000 family command reference lr percent 1use the lr percent command to configure lr. Traffic behavior view ls use the ls command to query for a specified file/directory. Ftp client view ls use the ls command to view the files in the specified directory as you would with the dir ...

  • Page 97

    3com router 5000/6000 family 97 command reference max-packet-process use the max-packet-process command to set the maximum number of processed packets per second on a certain vlan. System view md5-compatible use the md5-compatible command to configure isis to use the 3com-compatible md5 algorithm. Y...

  • Page 98

    98 3com router 5000/6000 family command reference min-active-links use the min-active-links command to configure the minimum number of available links required for the ima group to operate. Ima group interface view mkdir use the mkdir command to create a directory on the remote ftp server. Ftp clien...

  • Page 99

    3com router 5000/6000 family 99 command reference mobile-ip tunnel path-mtu-discovery use the mobile-ip tunnel path-mtu-discovery command to set the pmtu update policy. System view mobile-ip virtual-network use the mobile-ip virtual-network command to define a virtual network. System view mobile-net...

  • Page 100

    100 3com router 5000/6000 family command reference motorola base-svc use the motorola base-svc command to configure the start svc for voice routing on a dlci. Dlci view motorola encapsulation use the motorola encapsulation command to specify an encapsulation for motorola lcon on the dlci. Dlci view ...

  • Page 101

    3com router 5000/6000 family 101 command reference mpls ldp path-vectors use the mpls ldp path-vectors command to set the maximum value of path vector. System view mpls ldp remote-peer use the mpls ldp remote-peer command to create a remote-peer entity and enter remote-peer view. Remote-peer view sy...

  • Page 102

    102 3com router 5000/6000 family command reference mtracert use the mtracert command to trace the network path from the multicast source to the destination receiver along multicast distribution tree, according to either the multicast kernel routing table or rpf rule to the source. Any view multi-pat...

  • Page 103

    3com router 5000/6000 family 103 command reference nat outbound static use the nat outbound static command to apply on the interface one-to-one address translation configured using the nat static command. Interface view nat overlapaddress use the nat overlapaddress command to map an overlapping addr...

  • Page 104

    104 3com router 5000/6000 family command reference network-entity use the network-entity command to configure the name of network entity title (net) of the is-is routing process. Is-is view normal-connect slow-h245 use the normal-connect slow-h245 command to configure disabling the calling end from ...

  • Page 105

    3com router 5000/6000 family 105 command reference number-match use the number-match command to configure a global number match-policy. Voice dial program view number-substitute use the number-substitute command to create a number-substitute list and enter voice dial program view. Voice dial program...

  • Page 106

    106 3com router 5000/6000 family command reference ospf use the ospf command to enable the ospf protocol. System view ospf authentication-mode use the ospf authentication-mode command to configure the authentication mode and key between adjacent routers. Interface view ospf cost use the ospf cost co...

  • Page 107

    3com router 5000/6000 family 107 command reference packing timer use the packing-timer command to set the maximum waiting time for one pvc. Pvc view pad use the pad command to establish a pad connection with the remote site. User view pad-mode pos enable use the pad-mode pos enable command to enable...

  • Page 108

    108 3com router 5000/6000 family command reference peer allow-as-loop use the peer allow-as-loop command to configure the repeating times of the local as number. Bgp view vpnv4 view vpn instance view peer allow-as-loop use the peer allow-as-loop command to allow the as_path attribute in the received...

  • Page 109

    3com router 5000/6000 family 109 command reference peer filter-policy use the peer filter-policy import command to configure bgp to filter routes received from the peer (group) based on the acl. Use the peer filter-policy export command to configure bgp to filter routes advertised to the peer (group...

  • Page 110

    110 3com router 5000/6000 family command reference peer public-as-only use the peer public-as-only command to configure not to carry the private as number when transmitting bgp updates. Bgp view peer public-as-only use the peer public-as-only command to configure only to carry public as number rathe...

  • Page 111

    3com router 5000/6000 family 111 command reference peer timer use the peer timer command to configure keepalive and holdtime intervals for a peer (group). Bgp view peer upe use the peer upe command to configure bgp peer as the upe of hierarchical bgp/mpls vpn. Bgp view permanent-active use the perma...

  • Page 112

    112 3com router 5000/6000 family command reference pki domain use the pki domain command to enter pki domain view, and configure the parameters of ldap server and for certificate request and authentication. System view pki entity use the pki entity command to name a pki entity and enter pki entity v...

  • Page 113

    3com router 5000/6000 family 113 command reference portal auth-network use the portal auth-network command to configure a network segment for portal authentication. System view portal fast-authentication use the portal fast-authentication command to enable fast portal authentication. System view por...

  • Page 114

    114 3com router 5000/6000 family command reference pos-server source-ip use the pos-server source-ip command to bind the specified application with the source address of a tcp connection. System view pos-server wait-time use the pos-server wait-time command to set the pospad wait timer. System view ...

  • Page 115

    3com router 5000/6000 family 115 command reference ppp lcp mru consistent use the ppp lcp mru consistent command to enable ppp lcp to negotiation maximum receive unit (mru). Interface view ppp lqc use the ppp lqc command to enable ppp link quality control (lqc). Interface view ppp mp use the ppp mp ...

  • Page 116

    116 3com router 5000/6000 family command reference pppoe-client use the pppoe-client command to establish a pppoe session and specify the dialer bundle corresponding to the session. Ethernet interface (subinterface) view virtual ethernet interface view pppoe-server bind virtual-template use the pppo...

  • Page 117

    3com router 5000/6000 family 117 command reference pri-set (ct1/pri interface) use the pri-set command to bundle the timeslots of the ct1/pri interface into a pri-set. Ct1/pri interface view primary accounting use the primary accounting command to configure ip address and port number of the primary ...

  • Page 118

    118 3com router 5000/6000 family command reference public-key-code begin use the public-key-code begin command to enter public key code view. Public key view public-key-code end use the public-key-code end command to return from public key code view to public key view and to save the configured publ...

  • Page 119

    3com router 5000/6000 family 119 command reference queue wfq use the queue wfq command to configure the default-class to use wfq. Traffic behavior view quit use the quit command to return from current view to lower level view, or exit the system if current view is user view. Any view quit use the qu...

  • Page 120

    120 3com router 5000/6000 family command reference qos lr use the qos lr command to limit the transmitting rate of the interface. Interface (including the mfr interface) view qos max-bandwidth use the qos max-bandwidth command to configure the maximum interface bandwidth used when cbq enqueues packe...

  • Page 121

    3com router 5000/6000 family 121 command reference radius scheme use the radius scheme command to configure a radius scheme and enter its view. System view radius trap use the radius trap command to enable the radius server to send traps when it goes down. System view ras-on use the ras-on command t...

  • Page 122

    122 3com router 5000/6000 family command reference reflector cluster-id use the reflector cluster-id command to configure the cluster id of the route reflector. Bgp unicast view bgp multicast view vpnv4 view refresh bgp use the refresh bgp command to request the peer to retransmit routes or retransm...

  • Page 123

    3com router 5000/6000 family 123 command reference remote-ip use the remote-ip command to configure a remote ip address. The address should be the lsr id of the remote lsr. As remote peers adopt lsr id as their transport addresses, the last two remote peers use their lsr id as their transport addres...

  • Page 124

    124 3com router 5000/6000 family command reference reset bgp use the reset bgp peer-address command to reset the connection of bgp with a specified peer. User view reset bgp flap-info use the reset bgp flap-info command to reset the flap statistics of routes. User view reset bgp group use the reset ...

  • Page 125

    3com router 5000/6000 family 125 command reference reset dlsw bridge-entry use the reset dlsw bridge-entry command to clear the entry cache information in the dlsw bridge group. User view reset dlsw circuits use the reset dlsw circuits command to clear the dlsw virtual circuit information. User view...

  • Page 126

    126 3com router 5000/6000 family command reference reset firewall ethernet-frame-filter use the reset firewall ethernet-frame-filter command to clear the acl-based firewall statistics. User view reset firewall-statistics use the reset firewall-statistics command to clear the firewall statistics. Use...

  • Page 127

    3com router 5000/6000 family 127 command reference reset isis peer use the reset isis peer command to reset the is-is data of specified is-is neighbor. User view reset lapb use the reset lapb statistics command to clear the statistics about lapb. Interface view reset loadsharing use the reset loadsh...

  • Page 128

    128 3com router 5000/6000 family command reference reset nat use the reset nat command to clear up the mapping tables of address translation in the memory and release all the memory dynamically allocated to store the mapping tables. User view reset ospf use the reset ospf all command to reset all th...

  • Page 129

    3com router 5000/6000 family 129 command reference reset tcp statistics use the reset tcp statistics command to clear tcp traffic statistic information. After the execution of this command, there’s no prompt information on the screen, and the existing statistics are cleared. User view reset trapbuff...

  • Page 130

    130 3com router 5000/6000 family command reference reset web url-filter parameter counter use the reset web url-filter parameter counter command to clear the statistics of sql injection attack protection. User view reset x25 use the reset x25 command to reset statistics about x.25 on the specified i...

  • Page 131

    3com router 5000/6000 family 131 command reference rip metricin use the rip metricin command to configure the additional route metric added to the route when an interface receives rip packets. Interface view rip metricout use the rip metricout value command to enable rip to send routes out the inter...

  • Page 132

    132 3com router 5000/6000 family command reference route-distinguisher use the route-distinguisher command to configure rd for an mpls vpn instance. A vpn-instance cannot run until it is configured with an rd. Mbgp vpn-instance view route-policy use the route-policy command to create a route-policy ...

  • Page 133

    3com router 5000/6000 family 133 command reference sa duration use the sa duration command to set a sa duration of the ipsec policy. Ipsec policy view ipsec policy template view sa encryption-hex use the sa encryption-hex command to set the sa encryption key manually for the ipsec policy of manual m...

  • Page 134

    134 3com router 5000/6000 family command reference script trigger init use the script trigger init command to configure the modem script that will be executed when the system is powered on or rebooted. User interface view script trigger login use the script trigger login command to configure the mod...

  • Page 135

    3com router 5000/6000 family 135 command reference sdlc window use the sdlc window command to configure the length of the sdlc local response window. Synchronous serial interface view sdlc xid use the sdlc xid command to configure the xid of the sdlc. Synchronous serial interface view secondary acco...

  • Page 136

    136 3com router 5000/6000 family command reference send-busytone use the send-busytone command to enable busy tone sending on the fxo interface. Fxo voice subscriber-line view send-number (in voice entity view) use the send-number command to configure the number sending mode. Pots voice entity view ...

  • Page 137

    3com router 5000/6000 family 137 command reference service vbr-nrt use the service vbr-nrt command to specify the service type of pvc as variable bit rate-non real time (vbr-nrt) and specify the related rate parameters. Pvc view service vbr-rt use the service vbr-rt command to set the service type o...

  • Page 138

    138 3com router 5000/6000 family command reference shdsl rate use the shdsl rate command to set single-pair interface rate of the shdsl interface or just select auto-negotiation mode. You can specify maximum line rate. Atm (g.Shdsl) interface view shdsl snr-margin use the shdsl snr-margin command to...

  • Page 139

    3com router 5000/6000 family 139 command reference sip-call use the sip-call command to enable globally supplementary service. Body style (undo command description goes here) sip client view sip-comp use the sip-comp command to configure a sip compatibility option. Sip client view sip-comp use the s...

  • Page 140

    140 3com router 5000/6000 family command reference snmp-agent target-host use the snmp-agent target-host command to set the destination that receives snmp notifications. Use the snmp-agent target-host command in conjunction with the snmp-agent trap enable command. System view snmp-agent trap enable ...

  • Page 141

    3com router 5000/6000 family 141 command reference sot sdlc-status primary use the sot sdlc-status primary command to set the role of the router to sdlc primary node. Synchronous serial interface view sot sdlc-status secondary use the sot sdlc-status secondary command to set the role of the router t...

  • Page 142

    142 3com router 5000/6000 family command reference spf-schedule-interval use the spf-schedule-interval command to configure the route calculation interval of ospf. Ospf view spf-slice-size use the spf-slice-size c ommand to configure whether to set slice and the duration time each time when is-is pe...

  • Page 143

    3com router 5000/6000 family 143 command reference ssh user service-type use the ssh user service-type command to specify service type for a user. System view ssh2 use the ssh2 command to initiate a connection to the specified ssh server, and specify the preferred key exchange algorithm, encryption ...

  • Page 144

    144 3com router 5000/6000 family command reference startup saved-configuration use the startup saved-configuration command to specify the configuration file used at next startup. User view state use the state command to configure the state of the current isp domain or local user. Isp domain view loc...

  • Page 145

    3com router 5000/6000 family 145 command reference stopbits use the stopbits command to set the stop bits on the user interface. User interface view stub use the stub command to configure the type of an ospf area as the stub area. Ospf area view subscriber-line use the subscriber-line command to ent...

  • Page 146

    146 3com router 5000/6000 family command reference sysname use the sysname command to set the name of the router. System view system-view use the system-view command to enter system view from the current user view. User view t1 bert use the t1 bert command to start a bert test on the specified t1 li...

  • Page 147

    3com router 5000/6000 family 147 command reference tcp timer fin-timeout use the tcp timer fin-timeout command to configure the tcp finwait timer. System view tcp timer syn-timeout use the tcp timer syn-timeout command to configure the tcp synwait timer. System view tcp window use the tcp window com...

  • Page 148

    148 3com router 5000/6000 family command reference test-time begin use the test-time begin command to configure the start time and the lasting time of a test. Hwping test group view test-type use the test-type command to configure the type of the test. Hwping test group view tftp use the tftp comman...

  • Page 149

    3com router 5000/6000 family 149 command reference timeout use the timeout command to configure a timeout time for a test. Hwping test group view timer (digital e&m) use the timer command to configure the timeout values of the signals in the digital e&m signaling. Digital e&m voice subscriber-line v...

  • Page 150

    150 3com router 5000/6000 family command reference timer realtime-accounting tuse the timer realtime-accounting command to configure a real-time accounting interval. Radius view timer realtime-accounting use the timer realtime-accounting command to configure a real-time accounting interval. Tacacs+ ...

  • Page 151

    3com router 5000/6000 family 151 command reference tracert use the tracert command to trace the gateways by which a packet passes from source to destination for network connectivity test and fault location. Any view tracert clns use the tracert clns command to track the nodes along the route that le...

  • Page 152

    152 3com router 5000/6000 family command reference ttl propagate use the ttl propagate command to enable ip ttl duplication of mpls. Mpls view tunnel authentication use the l2tp tunnel authentication command to enable l2tp tunnel authentication. L2tp group view tunnel avp-hidden use the tunnel avp-h...

  • Page 153

    3com router 5000/6000 family 153 command reference undelete use the undelete command to restore a file from the recycle bin. User view undo schedule reboot use the undo schedule reboot command to cancel the configuration of the schedule reboot terminal service. User view undo synchronization use the...

  • Page 154

    154 3com router 5000/6000 family command reference using (ct3 interface) use the using command to configure the operating mode of a ct3 interface. Ct3 interface view vad-on use the vad-on command to enable silence detection function. Voice entity view validate source address use the validate-source-...

  • Page 155

    3com router 5000/6000 family 155 command reference vofr jitter-buffer use the vofr jitter-buffer command to configure a jitter buffer length. Voice view voice bandwidth use the voice bandwidth command to configure maximum bandwidth for voice calls. Frame relay class view voice-config use the voice-c...

  • Page 156

    156 3com router 5000/6000 family command reference vrbd use the vrbd command to view software version details, including product software version and the matched platform software version. Any view vrrp authentication-mode use the vrrp authentication-mode command to configure authentication mode and...

  • Page 157

    3com router 5000/6000 family 157 command reference web java-blocking extension delete use the web java-blocking extension delete command to delete a previously added extension name of java request packets. System view web java-blocking extension delete-all use the web java-blocking extension delete-...

  • Page 158

    158 3com router 5000/6000 family command reference web url-filter parameter delete use the web url-filter parameter delete command to delete a filter keyword previously added. System view web url-filter parameter delete-all use the web url-filter parameter delete-all command to delete all filter key...

  • Page 159

    3com router 5000/6000 family 159 command reference x25 ignore called-address use the x25 ignore called-address command to enable it to ignore the x.121 address of the called dte when x.25 initiates calls. Interface view x25 ignore calling-address use the x25 ignore calling-address command to enable ...

  • Page 160

    160 3com router 5000/6000 family command reference x25 roa-list use the x25 roa-list command to define roa list. System view x25 switch pvc use the x25 switch pvc (packet switching) command to configure one pvc route. Interface view x25 switch svc hunt-group use the x25 switch svc hunt-group command...

  • Page 161

    3com router 5000/6000 family 161 command reference x25 x121-address use the x25 x121-address command to set the x.121 address of an x.25 interface. Interface view x25 xot pvc use the x25 xot pvc command to add a pvc route of xot. Use the undo x25 pvc command to delete the specified pvc route of xot....

  • Page 162

    162 3com router 5000/6000 family command reference.