3Com 3C16894 Quick Reference Manual

Other manuals for 3C16894: Installation Manual, Installation Manual
Manual is about: 3Com 7757: Reference Guide

Summary of 3C16894

  • Page 1

    Copyright © 2006-2007, 3com corporation. All rights reserved. Www.3com.Com part number: 10016396 rev. Aa published: december 2007 3c om s witch 7750 f amily q uick r eference g uide overview this quick reference guide applies to the following switch 7750 models. About the command line interface to u...

  • Page 2

    1146 administrator-address 3com switch 7750 family quick reference guide displaying command parameters at the prompt, enter the name of the command followed by a space and ? . For example: boot ? The following parameters are displayed: attribute-switch exchange the file main-attribute and backup-att...

  • Page 3

    3com switch 7750 family holdtime 1147 quick reference guide holdtime cluster view use the holdtime command to configure the holdtime of a switch. Use the undo holdtime command to restore the default holdtime value. Ip-pool cluster view use the ip-pool command to configure a private ip address range ...

  • Page 4

    1148 acl 3com switch 7750 family quick reference guide acl user interface view use the acl command to apply an acl to filter telnet users. Use the undo acl command to disable the switch from filtering telnet users using the acl. Acl mode system view use the acl mode command to set the traffic classi...

  • Page 5

    3com switch 7750 family apply cost-type 1149 quick reference guide apply cost-type route policy view use the apply cost-type command to set the routing cost type of routing information. Use the undo apply cost-type command to cancel the setting argument. Apply ip next-hop route policy view use the a...

  • Page 6

    1150 arp max-entry 3com switch 7750 family quick reference guide arp max-entry system view use the arp max-entry command to set the total maximum number of arp entries. Use the undo arp max-entry command to restore the default setting. Arp protective-down recover interval system view use the arp pro...

  • Page 7

    3com switch 7750 family ascii 1151 quick reference guide ascii ftp client view use the ascii command to specify that files be transferred in the ascii mode. Attack-protection system view use the attack-protection command to set global telnet protection. After you execute this command, the system pro...

  • Page 8

    1152 balance 3com switch 7750 family quick reference guide balance bgp view use the balance command to configure bgp load balance. Use the undo balance command to cancel the load balance configuration. Bgp system view use the bgp command to enable bgp and enter the bgp view. Use the undo bgp command...

  • Page 9

    3com switch 7750 family boot bootrom 1153 quick reference guide boot bootrom user view use the boot bootrom command to update the boot rom. Boot bootrom default user view use the boot bootrom default command to use the current startup file to upgrade the boot roms. Boot bootrom default user view use...

  • Page 10

    1154 cd 3com switch 7750 family quick reference guide cd ftp client view use the cd command to change the work directory on the remote ftp server. Cd sftp client view use the cd command to change the current path on the remote sftp server. If you did not specify the remote-path argument, the current...

  • Page 11

    3com switch 7750 family compare-different-as-med 1155 quick reference guide compare-different-as-med bgp view/bgp multicast address family view use the compare-different-as-med command to enable comparison of med values from different as neighboring routes when determining the best route. Use the un...

  • Page 12

    1156 dampening 3com switch 7750 family quick reference guide dampening bgp view use the dampening command to make bgp route attenuation valid or modify various bgp route attenuation parameters. Use the undo dampening command to make the characteristics invalid. Databits user interface view use the d...

  • Page 13

    3com switch 7750 family default-cost 1157 quick reference guide default-cost ospf area view use the default-cost command to configure the cost of the default route transmitted by ospf to the stub or nssa area. Use the undo default-cost command to restore the default cost of the default route transmi...

  • Page 14

    1158 dhcp relay information strategy 3com switch 7750 family quick reference guide dhcp relay information strategy system view use the dhcp relay information strategy command to instruct a dhcp relay agent to perform specified operations to dhcp request packets that carry option 82. Use the undo dhc...

  • Page 15

    3com switch 7750 family dhcp server nbns-list 1159 quick reference guide dhcp server nbns-list system view, vlan interface view use the dhcp server nbns-list command to configure wins server ip address(es) for the specified dhcp interface address pool(s). Use the undo dhcp server nbns-list command t...

  • Page 16

    1160 dhcp-snooping information enable 3com switch 7750 family quick reference guide dhcp-snooping information enable system view use the dhcp-snooping information enable command to enable dhcp snooping option 82. Use the undo dhcp-snooping information enable command to disable dhcp snooping option 8...

  • Page 17

    3com switch 7750 family display acl remaining entry 1161 quick reference guide display acl remaining entry any view use the display acl remaining entry slot command to display the remaining acl entries on a specified slot. The displayed content includes the entry resource type, total entries resourc...

  • Page 18

    1162 display bgp routing-table 3com switch 7750 family quick reference guide display bgp routing-table any view use the display bgp routing-table command to display all the bgp routing information. Display bgp routing-table as-path-acl any view use the display bgp routing-table as-path-acl command t...

  • Page 19

    3com switch 7750 family display connection 1163 quick reference guide display connection any view use the display connection command to display information about the specified user connection or all user connections, so as to troubleshoot user connections. Display cpu any view use the display cpu co...

  • Page 20

    1164 display dhcp-snooping vlan 3com switch 7750 family quick reference guide display dhcp-snooping vlan any view use the display dhcp-snooping vlan command to display the ip-mac mapping relations recorded by the dhcp-snooping-enabled switch in the specified vlan. Display diagnostic-information any ...

  • Page 21

    3com switch 7750 family display gvrp statistics 1165 quick reference guide display gvrp statistics any view use the display gvrp statistics command to display the gvrp statistics of specified or all trunk ports. Display gvrp status any view use the display gvrp status command to display the global g...

  • Page 22

    1166 display ip interface 3com switch 7750 family quick reference guide display ip interface any view use the display ip interface command to display information about one specific or all interfaces. Display ip ip-prefix any view use the display ip ip-prefix command to display an address prefix list...

  • Page 23

    3com switch 7750 family display ipx routing-table 1167 quick reference guide display ipx routing-table any view use the display ipx routing-table command to view the ipx routing information. Display ipx service-table any view use the display ipx service-table command to view the contents of the ipx ...

  • Page 24

    1168 display local-user 3com switch 7750 family quick reference guide display local-user any view use the display local-user command to display information about a specific or all local users, so as to troubleshoot local user configuration. Display logbuffer any view use the display logbuffer comman...

  • Page 25

    3com switch 7750 family display msdp peer-status 1169 quick reference guide display msdp peer-status any view use the display msdp peer-status command to display the detailed information of the msdp peer state. Display msdp sa-cache any view use the display msdp sa-cache command to display (s, g) st...

  • Page 26

    1170 display ntdp 3com switch 7750 family quick reference guide display ntdp any view use the display ntdp command to display the global ntdp information. The information includes the range (in hop count) within which topology information is collected, the interval to collect topology information (t...

  • Page 27

    3com switch 7750 family display ospf retrans-queue 1171 quick reference guide display ospf retrans-queue any view use the display ospf retrans-queue command to display the information about the ospf retransmission queue. Display ospf routing any view use the display ospf routing command to display t...

  • Page 28

    1172 display poe-profile 3com switch 7750 family quick reference guide display poe-profile any view use the display poe-profile command to display detailed configuration information of the created poe profile for a switch. Display port any view use the display port command to check whether there are...

  • Page 29

    3com switch 7750 family display qos-interface traffic-bandwidth 1173 quick reference guide display qos-interface traffic-bandwidth any view use the display qos-interface traffic-bandwidth command to view the configuration information about bandwidth guarantee. Display qos-interface traffic-limit any...

  • Page 30

    1174 display rmon history 3com switch 7750 family quick reference guide display rmon history any view use the display rmon history command to display the rmon history information about a specified port. The information about the latest sample, including utilization, the number of errors, the total n...

  • Page 31

    3com switch 7750 family display snmp-agent group 1175 quick reference guide display snmp-agent group any view use the display snmp-agent group command to view group name, security model, state of various views and storage models. Display snmp-agent mib-view any view use the display snmp-agent mib-vi...

  • Page 32

    1176 display stp root 3com switch 7750 family quick reference guide display stp root any view use the display stp root command to display information about the root ports in the mstp region where the switch resides. Display supervision-module information any view use the display supervision-module i...

  • Page 33

    3com switch 7750 family display udp statistics 1177 quick reference guide display udp statistics any view use the display udp statistics command to view the statistics about udp packets. Display udp-helper server any view use the display udp-helper server command to display the information about the...

  • Page 34

    1178 dldp delaydown-timer 3com switch 7750 family quick reference guide dldp delaydown-timer system view use the dldp delaydown-timer command to set the delaydown timer. Use the undo dldp delaydown-timer command to restore the default delaydown timer setting. Dldp interval system view use the dldp i...

  • Page 35

    3com switch 7750 family dot1x authentication-method 1179 quick reference guide dot1x authentication-method system view use the dot1x authentication-method command to set the 802.1x authentication method. Use the undo dot1x authentication-method command to revert to the default 802.1x authentication ...

  • Page 36

    1180 dot1x version-check 3com switch 7750 family quick reference guide dot1x version-check system view, ethernet port view use the dot1x version-check command to enable 802.1x client version checking for specified ethernet ports. Use the undo dot1x version-check command to disable 802.1x client vers...

  • Page 37

    3com switch 7750 family filter-policy export 1181 quick reference guide filter-policy export bgp view/bgp multicast address family view use the filter-policy export command to filter the advertised routes and only the routes passing the filter can be advertised by bgp. Use the undo filter-policy exp...

  • Page 38

    1182 frequency 3com switch 7750 family quick reference guide frequency nqa test group view use the frequency command to configure an automatic test interval. Use the undo frequency command to disable an automatic test. Ftp user view use the ftp command to establish a control connection with an ftp s...

  • Page 39

    3com switch 7750 family gvrp 1183 quick reference guide gvrp system view, ethernet port view use the gvrp command to enable gvrp globally (in system view) or for a port (in ethernet port view). Use the undo gvrp command to disable gvrp globally (in system view) or on a port (in ethernet port view). ...

  • Page 40

    1184 hwtacacs scheme 3com switch 7750 family quick reference guide hwtacacs scheme system view use the hwtacacs scheme command to enter hwtacacs scheme view and create the specified hwtacacs scheme if it does not exist. Use the undo hwtacacs scheme command to delete an hwtacacs scheme. Icmp redirect...

  • Page 41

    3com switch 7750 family igmp group-policy 1185 quick reference guide igmp group-policy vlan interface view use the igmp group-policy command to set the filter of multicast groups on the vlan interface to control the access to ip multicast groups. Igmp group-policy vlan port view use the igmp group-p...

  • Page 42

    1186 igmp timer query 3com switch 7750 family quick reference guide igmp timer query vlan interface view use the igmp timer query command to configure the interval at which a router interface sends igmp query messages. Use the undo igmp timer query command to restore the default value. Igmp version ...

  • Page 43

    3com switch 7750 family igmp-snooping router-aging-time 1187 quick reference guide igmp-snooping router-aging-time system view use the igmp-snooping router-aging-time command to configure the aging time of the router port. Use the undo igmp-snooping router-aging-time command to restore the default a...

  • Page 44

    1188 info-center loghost 3com switch 7750 family quick reference guide info-center loghost system view use the info-center loghost command to enable information output to loghost by setting the ip address of the loghost. Use the undo info-center loghost command to cancel the configuration. Info-cent...

  • Page 45

    3com switch 7750 family ip address 1189 quick reference guide ip address vlan interface view use the ip address command to specify an ip address and subnet mask for the vlan interface. Use the undo ip address command to remove the ip address and subnet mask of the vlan interface. Ip as-path-acl syst...

  • Page 46

    1190 ip netstream export source 3com switch 7750 family quick reference guide ip netstream export source system view or netstream aggregation view use the ip netstream export source command to configure the source ip address of netstream export packets, which will be used as the source address of ud...

  • Page 47

    3com switch 7750 family ip userlog nat export host 1191 quick reference guide ip userlog nat export host system view use the ip userlog nat export host command to set the address and port number of the global destination server for log packets. Use the undo ip userlog nat export host command to rest...

  • Page 48

    1192 ipx rip mtu 3com switch 7750 family quick reference guide ipx rip mtu vlan interface view use the ipx rip mtu command to configure the ipx rip update packet size. Use the undo ipx rip mtu command to restore the default size. Ipx rip multiplier system view use the ipx rip multiplier command to c...

  • Page 49

    3com switch 7750 family ipx service 1193 quick reference guide ipx service system view use the ipx service command to add a static service entry to the service information table. Use the undo ipx service command to delete a static service entry from the service information table. Ipx split-horizon v...

  • Page 50

    1194 isis timer holding-multiplier 3com switch 7750 family quick reference guide isis timer holding-multiplier interface view use the isis timer holding-multiplier command to configure the number of invalid hello packets for an is-is neighbor. When a specified number of hello packets are not receive...

  • Page 51

    3com switch 7750 family lcd 1195 quick reference guide lcd ftp client view use the lcd command to display the local work directory on the ftp client. Level local user view use the level command to set the priority level of the user. Use the undo level command to restore the default priority level of...

  • Page 52

    1196 logging-host 3com switch 7750 family quick reference guide logging-host cluster view use the logging-host command to configure a logging host on the management device for the member devices in the cluster. Use the undo logging-host command to remove the public logging host for the member device...

  • Page 53

    3com switch 7750 family mac-address multicast interface 1197 quick reference guide mac-address multicast interface system view use the mac-address multicast command to manually add a multicast mac address entry. Use the undo mac-address multicast command to remove a multicast mac address entry. Mac-...

  • Page 54

    1198 mac-authentication timer 3com switch 7750 family quick reference guide mac-authentication timer system view use the mac-authentication timer command to configure the timers used in centralized mac address authentication. Use the undo mac-authentication timer command to restore a timer to its de...

  • Page 55

    3com switch 7750 family mirroring-group monitor-slot 1199 quick reference guide mirroring-group monitor-slot system view use the mirroring-group monitor-slot command to configure the destination mirroring i/o module, which must be ls81vsnp or ls82vsnp. In order to mirror a port to a i/o module, the ...

  • Page 56

    1200 move 3com switch 7750 family quick reference guide move user view use the move command to move a file to a specified directory. You can also assign a new name for the file. Msdp system view use the msdp command to enable msdp and enter msdp view. Use the undo msdp command to clear all configura...

  • Page 57

    3com switch 7750 family multicast-vlan subvlan 1201 quick reference guide multicast-vlan subvlan system view use the multicast-vlan subvlan command to configure one or multiple vlans as the sub-vlan(s) of the multicast vlan. Use the undo multicast-vlan subvlan command to cancel the sub-vlans of the ...

  • Page 58

    1202 nat ftp server 3com switch 7750 family quick reference guide nat ftp server vlan interface view use the nat ftp server command to configure a non-standard internal ftp server. Use the undo nat ftp server command to remove a non-standard internal ftp server configuration. Nat outbound vlan inter...

  • Page 59

    3com switch 7750 family network 1203 quick reference guide network bgp view/bgp multicast address family view use the network command to advertise the network segment route to the bgp routing table. Use the undo network command to cancel the existing configuration. Network-entity is-is view use the ...

  • Page 60

    1204 ntp-service broadcast-client 3com switch 7750 family quick reference guide ntp-service broadcast-client vlan interface view use the ntp-service broadcast-client command to configure ntp broadcast client mode. Use the undo ntp-service broadcast-client command to disable ntp broadcast client mode...

  • Page 61

    3com switch 7750 family originating-rp 1205 quick reference guide originating-rp msdp view use the originating-rp command to allow msdp peer to use the specified interface ip address as the rp address in the sa message when the msdp peer creates sa messages. Use the undo originating-rp command to ca...

  • Page 62

    1206 packet-filter 3com switch 7750 family quick reference guide packet-filter parity user interface view use the parity command to set the check mode of the user interface. Use the undo parity command to revert to the default check mode. Passive ftp client view use the passive command to set the da...

  • Page 63

    3com switch 7750 family peer default-route-advertise 1207 quick reference guide peer default-route-advertise bgp view use the peer default-route-advertise command to send the default route to the peer group. Use the undo peer default-route-advertise command to cancel the sending of the default route...

  • Page 64

    1208 peer public-as-only 3com switch 7750 family quick reference guide peer public-as-only bgp view/bgp multicast address family view use the peer public-as-only command to configure not to carry the as number when transmitting bgp update packets. Use the undo peer public-as-only command to configur...

  • Page 65

    3com switch 7750 family pim 1209 quick reference guide pim system view use the pim command to enter pim view to configure the global pim parameters. You cannot use the pim command to enable the pim protocol. Use the undo pim command to exit pim view to system view and clear the global pim configurat...

  • Page 66

    1210 poe mode 3com switch 7750 family quick reference guide poe mode ethernet port view and poe profile view use the poe mode command to configure the poe mode on the current port. Use the undo poe mode command to restore the poe mode on the current port to the default mode. Poe power max-value syst...

  • Page 67

    3com switch 7750 family port hybrid pvid vlan 1211 quick reference guide port hybrid pvid vlan ethernet port view use the port hybrid pvid vlan command to set the default vlan id for the hybrid port. Use the undo port hybrid pvid command to restore the default vlan id of the port. Port hybrid vlan e...

  • Page 68

    1212 port-security authorization ignore 3com switch 7750 family quick reference guide port-security authorization ignore ethernet port view use the port-security authorization ignore command to configure the port to ignore the authorization information delivered by the radius server. Use the undo po...

  • Page 69

    3com switch 7750 family primary accounting 1213 quick reference guide primary accounting radius scheme view use the primary accounting command to set the ip address and port number of the primary radius accounting server. Use the undo primary accounting command to restore the default ip address and ...

  • Page 70

    1214 public-key-code end 3com switch 7750 family quick reference guide public-key-code end public key edit view use the public-key-code end command to return from public key edit view to public key view and save the public keys you set. Public-key-code end public key edit view use the public-key-cod...

  • Page 71

    3com switch 7750 family radius nas-ip 1215 quick reference guide radius nas-ip system view use the radius nas-ip command to set the source address used by the nas to send radius packets. Use the undo radius nas-ip command to restore the default setting. Radius scheme system view use the radius schem...

  • Page 72

    1216 rename 3com switch 7750 family quick reference guide rename sftp client view use the rename command to rename a specified file or directory on an sftp server. Reset rip view use the reset command to reset the system configuration parameters of rip. Reset acl counter user view use the reset acl ...

  • Page 73

    3com switch 7750 family reset igmp group 1217 quick reference guide reset igmp group user view use the reset igmp group command to delete an existing igmp group from the vlan interface. The deleted group can be added to the vlan interface again. Reset igmp-snooping statistics user view use the reset...

  • Page 74

    1218 reset multicast routing-table 3com switch 7750 family quick reference guide reset multicast routing-table user view use the reset multicast routing-table command to clear the routing entries in the multicast core routing table and remove the corresponding forwarding entries in the mfc forwardin...

  • Page 75

    3com switch 7750 family reset vrrp statistics 1219 quick reference guide reset vrrp statistics user view use the reset vrrp command to clear the statistics information about vrrp. Retry radius scheme view use the retry command to set the maximum number of transmission attempts of radius requests. Us...

  • Page 76

    1220 rip metricout 3com switch 7750 family quick reference guide rip metricout interface view use the rip metricout command to configure the additional route metric added to the rip routes to be transmitted on an interface. Use the undo rip metricout command to restore the default value of this addi...

  • Page 77

    3com switch 7750 family router id 1221 quick reference guide router id system view use the router id command to configure the id of a bgp router. Use the undo router id command to cancel the router id that has been set. Rrpp domain system view use the rrpp domain command to create an rrpp domain and...

  • Page 78

    1222 schedule reboot delay 3com switch 7750 family quick reference guide schedule reboot delay user view use the schedule reboot delay command to schedule a reboot on the switch, and set the reboot waiting delay. Use the undo schedule reboot command to cancel the scheduled reboot. Scheme isp domain ...

  • Page 79

    3com switch 7750 family set authentication password 1223 quick reference guide set authentication password user interface view use the set authentication password command to set the local password. Use the undo set authentication password command to remove the local password. Set backboard enhance s...

  • Page 80

    1224 slave restart 3com switch 7750 family quick reference guide slave restart user view use the slave restart command to restart the slave module. Slave switchover user view use the slave switchover command to perform master/slave switchover manually. Slave update configuration user view use the sl...

  • Page 81

    3com switch 7750 family snmp-agent packet max-size 1225 quick reference guide snmp-agent packet max-size system view use the snmp-agent packet max-size command to set the maximum size of snmp packet that the agent can send/receive. Snmp-agent sys-info system view use the snmp-agent sys-info command ...

  • Page 83

    3com switch 7750 family ssh server rekey-interval 1227 quick reference guide ssh server rekey-interval system view use the ssh server rekey-interval command to set the update interval for the server key. Use the undo ssh server rekey-interval command to cancel the current configuration. Ssh server t...

  • Page 84

    1228 stop-accounting-buffer enable 3com switch 7750 family quick reference guide stop-accounting-buffer enable radius scheme view use the stop-accounting-buffer enable command to enable the switch to buffer the stop-accounting requests that bring no response. Use the undo stop-accounting-buffer enab...

  • Page 85

    3com switch 7750 family stp interface edged-port 1229 quick reference guide stp interface edged-port system view use the stp interface edged-port enable command to configure the specified ethernet port(s) as edge ports in system view. Use the stp interface edged-port disable command to configure the...

  • Page 86

    1230 stp no-agreement-check 3com switch 7750 family quick reference guide stp no-agreement-check ethernet port view use the stp no-agreement-check command to enable the rapid transition feature for a port. Use the stp no-agreement-check command to disable the rapid transition feature. Stp pathcost-s...

  • Page 87

    3com switch 7750 family stp tc-protection threshold 1231 quick reference guide stp tc-protection threshold system view use the stp tc-protection threshold command to set the upper threshold of the times for a switch to remove its mac address table within 10 seconds. Use the undo stp tc-protection th...

  • Page 88

    1232 super password 3com switch 7750 family quick reference guide super password system view use the super password command to set the password for users to switch to a higher user level. To prevent unauthorized accesses, you can use this command to require users to provide the password when they sw...

  • Page 89

    3com switch 7750 family terminal trapping 1233 quick reference guide terminal trapping user view use the terminal trapping command to enable terminal trap information display. Use the undo terminal trapping command to disable this function. Test-enable nqa test group view use the test-enable command...

  • Page 90

    1234 timer lsp-refresh 3com switch 7750 family quick reference guide timer lsp-refresh is-is view use the timer lsp-refresh command to set lsp updating period. Use the undo timer lsp-refresh to resume the default configuration. Timer quiet radius scheme view use the timer quiet command to set the wa...

  • Page 91

    3com switch 7750 family traffic-accounting traffic-group 1235 quick reference guide traffic-accounting traffic-group system view use the traffic-accounting traffic-group command to create a traffic group or enter the view of an existing traffic group. Use the undo traffic-accounting traffic-group co...

  • Page 92

    1236 udp-helper server 3com switch 7750 family quick reference guide udp-helper server vlan interface view use the udp-helper server command to specify a destination server for the udp broadcast packets to be forwarded. Use the undo udp-helper server command to remove a configured destination server...

  • Page 93

    3com switch 7750 family vlan 1237 quick reference guide vlan system view use the vlan command to enter a vlan view. If the vlan identified by the vlan-id argument does not exist, this command creates the vlan and then enters the vlan view. Use the undo vlan command to remove a vlan. Vlan all system ...

  • Page 94

    1238 voice vlan mac-address 3com switch 7750 family quick reference guide voice vlan mac-address system view use the voice vlan mac-address command to set an oui address used for a voice vlan to identify voice devices. Use the undo voice vlan mac-address command to disable an oui address from being ...