1. DL manuals
  2. 3Com
  3. Network Hardware
  4. 3C433279A
  5. Release Note

3Com 3C433279A Release Note

Manual is about: SuperStack II Remote Access System 1500

Summary of 3C433279A

  • Page 1

    Part no. 1.024.2320 rev ca june 2000 ® r elease n otes s uper s tack ® ii r emote a ccess s ystem 1500 r elease 2.5 these release notes contain information for release 2.5 of the superstack ® ii remote access system 1500 (ras 1500). It includes the following: ■ new features ............................

  • Page 2

    2 r elease n otes s uper s tack ® ii r emote a ccess s ystem 1500 r elease 2.5 new features the following are new features in this release: mschap version 1 and mschap version 2 ras 1500 includes support for local, remote authentication dial in user services (radius) and nt nos authentication. In ad...

  • Page 3

    New features 3 file compression release 2.5 includes improved file compression for internal file storage, increasing the amount of free space on the flash of the router unit. This allows for larger configuration files stored locally on the flash, and reduces the frequency of ras 1500 going into ‘fla...

  • Page 4

    4 r elease n otes s uper s tack ® ii r emote a ccess s ystem 1500 r elease 2.5 udp pat release 2.5 includes support for user data protocol (udp) pat over the wan interface. Udp pat sets a static address mapping translation for a connection and associates a user name with that connection. Udp pat tra...

  • Page 5

    New features 5 note: pat can only be used when the isp has provided only one ip address. This one ip address will dynamically change with each new connection. Dynamic nat release 2.5 includes support for dynamic network address translation (nat) over the wan interface. Dynamic nat configures and ass...

  • Page 6

    6 r elease n otes s uper s tack ® ii r emote a ccess s ystem 1500 r elease 2.5 below is an example of dynamic nat. The command, add nat dynamic user natd count 4 public_pool_start 2.2.2.2 sets (the count of) “4” consecutive isp-assigned addresses beginning with the isp-assigned address “2.2.2.2” to ...

  • Page 7

    New features 7 you can also set static nat using cli. The cli command for adding static nat over the wan interface is as follows: add nat static user this command should be followed sequentially by the following sub commands. See the table below for definitions of the parameters. Private_address pub...

  • Page 8

    8 r elease n otes s uper s tack ® ii r emote a ccess s ystem 1500 r elease 2.5 addresses are “broadcast” addresses and are not available for nat. The second address in the contiguous range is reserved for the ras 1500 and also is not available for nat. Both dynamic and static nat can be used simulta...

  • Page 9

    Operational information 9 operational information the following operational information is associated with this release: closing a telnet issue resolved closing a telnet session by clicking the box in the top right corner of the window will now properly close the session. Lingering user sessions hav...

  • Page 10

    10 r elease n otes s uper s tack ® ii r emote a ccess s ystem 1500 r elease 2.5 modifying dlci the digital (data) link connection identifier (dlci) of a frame relay user, cannot be modified directly from the lan-to-lan and shared isp pages of the ras 1500 web configurator. To modify the dlci, you mu...

  • Page 11

    Operational information 11 ras1500>disable datalink ppp interface rm0/wan:1 ras1500>delete user ras1500>delete datalink ppp interface rm0/wan:1 b) you may add a new entry in the lan-to-lan or the shared isp, through the web configurator, based on your needs. Frame relay local management interface th...

  • Page 12

    Relnotes2.5.Fm page 12 thursday, june 8, 2000 2:42 pm.