1. DL manuals
  2. 3Com
  3. Wireless Access Point
  4. 3CRWX275075A - Wireless LAN Managed Access Point 2750
  5. Quick Start Manual

3Com 3CRWX275075A - Wireless LAN Managed Access Point 2750 Quick Start Manual

Other manuals for 3CRWX275075A - Wireless LAN Managed Access Point 2750: Quick Start Manual
Manual is about: AP2750 Managed Access Point

Summary of 3CRWX275075A - Wireless LAN Managed Access Point 2750

  • Page 1

    Quick start guide ap2750 managed access point 3crwx275075a the 3com ap2750 managed access point provides ieee 802.11a or 802.11b/g wireless access to the network. The access point is designed for use with a 3com wireless lan switch, and requires hardware installation only. All configuration for the ...

  • Page 2

    2 3com ap2750 managed access point features feature description power port the access point can be powered either via power over ethernet (poe), or by an external power supply (not included) that is plugged into the power port. Serial port the serial port is not supported. Ethernet port the ethernet...

  • Page 3: Observing Safety Precautions

    3 observing safety precautions this equipment must be installed in compliance with local and national building codes, regulatory restrictions, and fcc rules. For the safety of people and equipment, only professional network personnel should install the access point. 1 unpacking the access point make...

  • Page 4: Attaching The Antennas

    4 3 attaching the antennas carefully unpack the standard detachable antennas. Screw the antennas on to the antenna connectors on the access point and hand-tighten them. After network startup, you may need to adjust the antennas to fine-tune coverage in your area. For best results, adjust the antenna...

  • Page 5

    5 the figures below show the mounting bracket being mounted to a wall, and then a cable being routed through the large opening on the back of the mounting bracket. 4 connect the ethernet cable (and power cable, if applicable) to the port(s) on the front of the access point. 5 snap the access point o...

  • Page 6: Tabletop Mounting

    6 tabletop mounting to install the access point on a flat surface such as a table or desktop: 1 remove the backing from the four rubber feet and attach them on the bottom of the mounting bracket that is attached to the access point. 2 place the access point on the table. 3 connect the ethernet cable...

  • Page 7: Checking The Led Indicators

    7 6 checking the led indicators when the access point is connected to power, leds indicate activity as follows (solid led indicates connection; blinking led indicates activity): troubleshooting refer to the mobility system configuration guide or to the 3com wireless lan switch reference manual to ob...

  • Page 8: Regulatory Information

    8 regulatory information the 3com ap2750 managed access point (3crwx275075a) must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety sta...

  • Page 9

    9 • increase the distance between the equipment and the receiver • connect the equipment to outlet on a circuit different from that to which the receiver is connected • consult the dealer or an experienced radio/tv technician for help the user may find the following booklet prepared by the federal c...

  • Page 10

    10 canada - industry canada (ic) this device complies with rss 210 of industry canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this...

  • Page 11

    11 europe - eu declaration of conformity marking by the above symbol indicates compliance with the essential requirements and other relevant provisions of the r&tte directive of the european union (1999/5/ec). This equipment meets the following conformance standards: en300 328, en301 893, en301 489-...

  • Page 12

    12 a copy of the signed declaration of conformity can be downloaded from the product support web page for the ap2750 (3crwx275075a) at http://www.3com.Com. German hiermit erklärt 3com corporation, dass sich dieser/diese/dieses managed accces point in Übereinstimmung mit den grundlegenden anforderung...

  • Page 13

    13 europe - restrictions for use of 2.4ghz frequencies in european community countries this device may be operated indoors or outdoors in all countries of the european community using the 2.4ghz band: channels 1 - 13, except where noted below. • in italy the end-user must apply for a license from th...

  • Page 14

    14 • the 5ghz radio's autochannelselect/smartselect setting described in the user guide must always remain enabled to ensure that automatic 5ghz channel selection complies with european requirements. The current setting for this feature is found in the 5ghz radio configuration window as described in...

  • Page 15

    15 reduce power to 25% and recheck link rate: 5 repeat steps 3 and 4 using a "transmit power" of quarter (-6db) and check if majority of station link rates are decreased from 54mbps. If the link rates using the -6db setting are now: • lower than the maximum possible values, the -6db power reduction ...

  • Page 16

    Copyright © 2004 3com corporation. All rights reserved. 3com and the 3com logo are registered trademarks of 3com corporation. All other company and product names may be trademarks of the respective companies with which they are associated. Dia27507-5aaa 02 published december 2004.