- DL manuals
- 3Com
- Switch
- 5500 SI - Switch - Stackable
- Quick Reference Manual
3Com 5500 SI - Switch - Stackable Quick Reference Manual
3C
OM
S
WITCH
5500 F
AMILY
Q
UICK
R
EFERENCE
G
UIDE
Overview
This Quick Reference Guide applies to the following Switch 5500 models running software version 3.2:
About the Command Line Interface
To use and navigate the command line interface of your unit, please refer to the following points for assistance:
■
When initially accessing the command line interface, press Enter when prompted. The User View
menu for the unit
displays. This is indicated by the chevron brackets around the name of the unit at the prompt, for example,
(where xx is either EI or SI).
■
When in the System View menu, square brackets appear around the name of the unit at the
prompt, for example,
[sw5500-xx]
.
■
You must be in the System View menu to access the configurable CLI commands.
■
Some commands can be entered directly at any prompt from anywhere in the interface.
■
If you enter part of a command followed by a ? (with no space between), the CLI will show you
all the commands
that begin in that way.
■
The term ‘view’ may be used interchangeably with the term ‘menu’.
■
The
undo
c
ommand is placed before the command you wish to undo, for example,
undo setauthentication
password.
■
■
Enter the first few characters of a command and press TAB to enter the full command without
having to input the
entire command (where there is only one command that starts with the entered characters).
■
Use the Up Arrow key at the prompt to repeat the previous command string.
■
Use the Delete key to delete the character after the cursor; the Backspace key deletes the character
before the cursor.
■
When entering physical port numbers, Enter the port number as
x/0/z
, where x is the unit
number and z is the
physical port number.
Switch 5500-SI 28-Port (3CR17151-91)
Switch 5500-SI 52-Port (3CR17152-91)
Switch 5500-EI 28-Port (3CR17161-91)
Switch 5500-EI 52-Port (3CR17162-91)
Switch 5500-EI PWR 28-Port (3CR17171-91)
Switch 5500-EI PWR 52-Port (3CR17172-91)
Switch 5500-EI 28-Port FX (3CR17181-91)
Switch 5500G-EI 24-Port (3CR17250-91)
Switch 5500G-EI 48-Port (3CR17251-91)
Switch 5500G-EI PWR 24-Port (3CR17252-91)
Switch 5500G-EI PWR 48-Port (3CR17253-91)
Switch 5500G-EI 24-Port SFP (3CR17258-91)
Copyright © 2006, 3Com Corporation. All rights reserved.
www.3Com.com
Part Number: 10014924-AA Rev. AA
Published: June, 2006
Summary of 5500 SI - Switch - Stackable
Page 1
3c om s witch 5500 f amily q uick r eference g uide overview this quick reference guide applies to the following switch 5500 models running software version 3.2: about the command line interface to use and navigate the command line interface of your unit, please refer to the following points for ass...
Page 2
3com switch 5500 family quick reference guide displaying command parameters at the prompt, enter the name of the command followed by a space and ? . For example: boot ? The following parameters are displayed: attribute-switch exchange the file main-attribute and backup-attribute. Boot-loader select ...
Page 3
3com switch 5500 family 3 quick reference guide acl use the acl command to reference acl and implement the acl control to the telnet users. User interface view acl use the acl command to define an acl identified by a number, and enter the corresponding acl view. System view active region-configurati...
Page 4
3com switch 5500 family quick reference guide arp check enable use the arp check enable command to enable the checking of an arp entry so the device does not learn the arp entry where the mac address is a multicast mac address. System view arp static use the arp static command to manually configure ...
Page 5
3com switch 5500 family 5 quick reference guide boot boot-loader backup-attribute use the boot boot-loader backup-attribute command to assign the backup attribute to an app file on one switch or all switches in the fabric, so as to use this app file as the backup boot file upon next startup of switc...
Page 6
3com switch 5500 family quick reference guide clock datetime use the clock datetime command to set the current system time and date. User view clock summer-time use the clock summer-time command to set the name, time range and offset of the daylight saving time. User view clock timezone use the cloc...
Page 7
3com switch 5500 family 7 quick reference guide debugging use the debugging command to enable the system debugging. User view debugging arp packet use the debugging arp command to enable arp debugging. User view debugging dhcp client use the debugging dhcp client command to enable dhcp client debugg...
Page 8
3com switch 5500 family quick reference guide debugging multicast status-forwarding use the debugging multicast status-forwarding to enable multicast forwarding status debugging functions. User view debugging ntp-service use the debugging ntp-service command to debug different ntp services. User vie...
Page 9
3com switch 5500 family 9 quick reference guide default type use the default type command to configure the default type when ospf redistributes external routes. Ospf view delete use the delete command to delete a specified file from the storage device of the switch. User view delete use the delete c...
Page 10
3com switch 5500 family quick reference guide dhcp-server use the dhcp-server command to map the current vlan interface to a dhcp server group. Vlan interface view dhcp server detect use the dhcp server detect command to enable the private dhcp server detecting function. System view dhcp server dns-...
Page 11
3com switch 5500 family 11 quick reference guide dhcp server voice-config interface use the dhcp server voice-config interface command to configure option 184 and its sub-options, which will be sent to dhcp clients by a dhcp server as well when the dhcp server assigns ip addresses of specified addre...
Page 12
3com switch 5500 family quick reference guide display brief interface use the display brief interface command to display the configuration information about one specific or all ports in brief, including the port type, connection state, connection rate, duplex attribute, link type and default vlan id...
Page 13
3com switch 5500 family 13 quick reference guide display dhcp client use the display dhcp client command to view detailed information about address allocation at dhcp client. Any view display dhcp-security use the display dhcp-security command to display one or all user address entries, or a specifi...
Page 14
3com switch 5500 family quick reference guide display drv use the display drv command to display mnt module driver debugging information. Any view display fan use the display fan command to display the working state of the built-in fans. Any view display fib use the display fib command to view the s...
Page 15
3com switch 5500 family 15 quick reference guide display history-command use the display history-command command to view the commands previously entered during this login session, up to a specified maximum. Any view display hwtacacs use the display hwtacacs command to view configuration information ...
Page 16
3com switch 5500 family quick reference guide display ip routing-table ip_address1 ip_address2 use the display ip routing-table ip_address1 mask1 ip_address2 mask2 command to view the route information for the specified address range. Any view display ip routing-table ip-prefix use the command displ...
Page 17
3com switch 5500 family 17 quick reference guide display logbuffer use the display logbuffer command to display the status of the log buffer and the records in the log buffer. Any view display loopback-detection use the display loopback-detection command to display whether loopback detection functio...
Page 18
3com switch 5500 family quick reference guide display multicast forwarding-table use the display multicast forwarding-table to view the information of ip multicast forwarding table. Any view display multicast routing-table use the display multicast routing-table to view the information of ip multica...
Page 19
3com switch 5500 family 19 quick reference guide display ospf peer use the display ospf peer command to view detailed ospf peer information. Any view display ospf peer brief use the display ospf peer brief command to display the brief information about the ospf neighbors in different areas, includin...
Page 20
3com switch 5500 family quick reference guide display poe power use the display poe interface power command, you can view the power information of a specific port or all ports on the switch. Any view display poe power supply use the display poe powersupply command to view the parameters of the power...
Page 21
3com switch 5500 family 21 quick reference guide display qos-interface traffic-statistic use the display qos-interface traffic-statistic command to view the traffic statistics information. Any view display qos-profile use the display qos-profile command to view qos profile configuration information....
Page 22
3com switch 5500 family quick reference guide display rsa local-key-pair public use the display rsa local-key-pair public command to display the public key of the server host key pair. If no key pair is generated, the system prompts “rsa keys not found”. Any view display rsa peer-public-key use the ...
Page 23
3com switch 5500 family 23 quick reference guide display ssh-server source-ip use the display ssh-server source-ip command to display the source ip address of the ssh server. If no source ip address is specified, 0.0.0.0 is displayed. Any view display ssh user-information use the display ssh user-in...
Page 24
3com switch 5500 family quick reference guide display transceiver-information interface use the display transceiver-information interface command to display information about a specified optical port, including: any view display trapbuffer use the display trapbuffer command to display the status of ...
Page 25
3com switch 5500 family 25 quick reference guide dldp use the dldp command to either enable or disable the dldp on either all the optical switches or current switch. System view ethernet port view dldp authentication-mode use the dldp authentication-mode command to set the dldp authentication mode a...
Page 26
3com switch 5500 family quick reference guide dot1x port-control use the dot1x port-control command to configure the mode for 802.1x to perform access control on the specified interface. Ethernet port view dot1x port-method use the dot1x port-method command to configure the base for 802.1x to perfor...
Page 27
3com switch 5500 family 27 quick reference guide file prompt use the file prompt command to modify the prompt mode of file operations on the switch. System view filter-policy export use the filter-policy export command to configure to set the filtering conditions of the routing information advertise...
Page 29
3com switch 5500 family 29 quick reference guide gvrp registration use the gvrp registration command to configure the gvrp registration type on a port. Ethernet port view header use the header command to configure the system to display a header during user log in. System view help use the help comma...
Page 30
3com switch 5500 family quick reference guide igmp group-limit use the igmp group-limit command to configure the maximum number of multicast groups that can be added to a vlan interface. Vlan interface view igmp group-policy use the igmp group-policy command to set the filter of multicast groups on ...
Page 31
3com switch 5500 family 31 quick reference guide igmp version use the igmp version command to specify the version of igmp that a router uses. Vlan interface view import-route using the import-route command, you can import the external routing information of another routing protocol. Ospf view import...
Page 32
3com switch 5500 family quick reference guide info-center timestamp loghost use the info-center timestamp loghost command to set the format of time stamp to be sent to log host. System view info-center trapbuffer use the info-center trapbuffer command to output information to the trap buffer. System...
Page 33
3com switch 5500 family 33 quick reference guide lacp port-priority use the lacp port priority command to configure port priority value. Ethernet port view lacp system-priority use the lacp system-priority command to configure system priority value. System view language-mode use the language-mode co...
Page 34
3com switch 5500 family quick reference guide loopback-detection per-vlan enable use the loopback-detection per-vlan enable command to enable loopback detection function for all vlans with trunk ports and hybrid ports. Ethernet port view ls use the ls command to display the files in the specified di...
Page 35
3com switch 5500 family 35 quick reference guide memory auto-establish enable use the memory auto-establish enable command to allow the routing protocol connection that is forcibly disconnected to recover automatically when the idle memory of the switch reaches this value. System view memory { safet...
Page 36
3com switch 5500 family quick reference guide multicast-source-deny use the multicast-source-deny command to enable the multicast source deny feature. System view ethernet port view multicast-suppression use multicast-suppression to configure the amount of multicast traffic that will be accepted on ...
Page 37
3com switch 5500 family 37 quick reference guide ntdp timer hop-delay use the ntdp timer hop-delay command to set delay for collected devices to forward topology collection requests. System view ntdp timer port-delay use the ntdp timer port-delay command to set the delay that a port waits to forward...
Page 38
3com switch 5500 family quick reference guide ospf authentication-mode using the ospf authentication-mode command, you can configure the authentication mode and key between adjacent routers. Vlan interface view the passwords for the authentication keys of routers on the same network segment must be ...
Page 39
3com switch 5500 family 39 quick reference guide password use the password command to configure or change the system login password for a user. Local user view password-control use the password-control command to configure login passwords. System view password-control enable use the password-control...
Page 40
3com switch 5500 family quick reference guide pim dm use the pim dm to enable pim-dm (dense mode). Interface view pim neighbor-limit use the pim neighbor-limit command to limit the pim neighbors on an interface. No neighbor can be added when the limit is reached. Vlan interface view pim neighbor-pol...
Page 41
3com switch 5500 family 41 quick reference guide port hybrid pvid vlan use the port hybrid pvid vlan command to configure the default vlan id of the hybrid port. Ethernet port view port hybrid vlan use the port hybrid vlan command to add the port to the specified vlan(s). The port needs to have been...
Page 42
3com switch 5500 family quick reference guide preference using the preference command, you can configure the ospf protocol route preference. Ospf view preference use the preference command to configure the route preference of rip. Rip view primary accounting use the primary accounting command to con...
Page 43
3com switch 5500 family 43 quick reference guide qos cos-local-precedence-map use the qos cos-local-precedence-map command to configure “cos local-precedence” mapping table system view qos-profile use the qos-profile command to create a qos profile and enter the corresponding view. For an existing p...
Page 44
3com switch 5500 family quick reference guide reset counters interface use the reset counters interface command to reset the statistical information on the port and count the related information again on the port for the user. User view reset dhcp server conflict use the reset dhcp server conflict c...
Page 45
3com switch 5500 family 45 quick reference guide reset multicast routing-table use the reset multicast routing-table command to clear route entries from the core multicast routing table, as well as mfc forwarding entries. User view reset ndp statistics use the reset ndp statistics command to reset t...
Page 46
3com switch 5500 family quick reference guide reset vrrp statistics use the reset vrrp command to clear the statistics information about vrrp. User view resilient-arp enable use the resilient-arp enable command to enable the resilient arp function. System view resilient-arp interface vlan-interface ...
Page 47
3com switch 5500 family 47 quick reference guide rip work use the rip work command to enable the rip on an interface. This is the default. Interface view rmdir use the rmdir command to delete the specified directory from the remote sftp server. Sftp client view rmon alarm use the rmon alarm command ...
Page 48
3com switch 5500 family quick reference guide secondary accounting use the secondary accounting command to configure a secondary tacacs accounting server. Hwtacacs view secondary authentication use the secondary authentication command to configure a secondary tacacs authentication server. Hwtacacs v...
Page 49
3com switch 5500 family 49 quick reference guide shutdown use the shutdown command to shut down the specified msdp peer. Msdp view silent-interface using the silent-interface command, you can prevent an interface from transmitting ospf packets. Ospf view snmp-agent community use the snmp-agent commu...
Page 50
3com switch 5500 family quick reference guide snmp-agent usm-user use the snmp-agent usm-user command to add a new community name or, if you use the v3 parameter, a new user to an snmp group. System view snmp-host use the snmp-host command to configure the public snmp host for members inside a clust...
Page 51
3com switch 5500 family 51 quick reference guide ssh user username authentication-type use the ssh user username authentication-type command to define authentication type for a designated user. System view ssh2 use the ssh2 command to enable the connection between ssh client and server, define key e...
Page 52
3com switch 5500 family quick reference guide stp bpdu-protection use the stp bpdu-protection command to enable the bpdu protection function. System view stp bridge-diameter use the stp bridge-diameter command to set the network diameter of a switched network, which is represented in terms of the ma...
Page 53
3com switch 5500 family 53 quick reference guide stp mcheck use the stp mcheck command to perform the mcheck operation for the current port. Ethernet port view stp mode use the stp mode command to set the mstp operation mode of the switch. System view stp pathcost-standard use the stp pathcost-stand...
Page 54
3com switch 5500 family quick reference guide stub using the stub command, you can configure the type of an ospf area as “stub”. Ospf area view summary use the summary command to activate rip-2 automatic route summarization. This is the default. Rip view super use the super command to give users acc...
Page 55
3com switch 5500 family 55 quick reference guide terminal monitor use the terminal monitor command to enable the log debugging/log/trap on the terminal monitor. User view terminal trapping use the terminal trapping command to enable terminal trap information display. User view test-enable use the te...
Page 56
3com switch 5500 family quick reference guide timer quiet use the timer quiet command to set the waiting time before the primary server resumes the active state. Hwtacacs view timer realtime-accounting use the timer realtime-accounting command to set the real-time accounting interval. Hwtacacs view ...
Page 57
3com switch 5500 family 57 quick reference guide undo snmp-agent use the undo snmp-agent command to disable all versions of snmp running on the server. System view unicast-suppression use unicast-suppression to configure the amount of unicast traffic that will be accepted on a port. Ethernet port vi...
Page 58
3com switch 5500 family quick reference guide vlan-vpn uplink enable use the vlan-vpn uplink enable command to configure a port to be a vlan-vpn uplink port. Ethernet port view vlink-peer use the vlink-peer command to create and configure a virtual link. Ospf area view voice-config use the voice-con...
Page 59
3com switch 5500 family 59 quick reference guide vrrp vrid track use the vrrp vrid track command to set a vlan interface to be tracked. Vlan interface view vrrp vrid track detect-group use the vrrp vrid command to enable the auto detect function when employing vrrp. Vlan interface view vrrp vrid vir...