- DL manuals
- 909
- Chainsaw
- 20VCSG
- Instruction Manual
909 20VCSG Instruction Manual
Summary of 20VCSG
Page 1
Black cyan magenta yellow code: 20vcsg date: 130827 edition: 6 op: dcr instruction manual 20vcsg 20v lithium-ion pruning chainsaw 20vcsg im ed6.Indd 1 28/8/13 8:03:13 am.
Page 2
2 contents warranty power tools for full details please visit us at www.909.Com warranty 2 introduction 3 environmental protection 3 description of symbols 3 specifications 3 general safety rules 4 additional safety rules for electric chainsaws 5 additional safety rules for the charger 6 additional ...
Page 3
3 description of symbols the rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Double insulated for additional protection. Conforms to relevant stand...
Page 4
4 general safety rules warning. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains...
Page 5
5 b) do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. C) disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing acces...
Page 6
6 • never cut into the ground. • never cut into wire fences. • never cut into saplings. • never cut into prepared wood. • use the chainsaw to cut wood only. • use the bar cover when moving the electric chainsaw away from the working site. • during transport the battery must be removed to avoid accid...
Page 7
7 • do not disassemble the charger. Phone to speak with an experienced 909 customer service representative or contact an authorised service centre for assistance. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when you us...
Page 8
8 • if you wish to charge a second battery pack, unplug the charger from the mains supply and leave it for at least 15 minutes. After this time you can charge a second battery pack. Additional safety rules related to the battery pack and battery safety • use only the 909 batteries supplied with the ...
Page 9
9 when to charge the battery new battery packs are shipped in a low charge condition and must be fully charged before use. It takes approximately 8 hours to fully charge a new battery and 3 - 5 hours once the battery has been used in the tool a few times. Charging of batteries should not be undertak...
Page 10
10 12. On/off trigger switch 13. Battery/plug pack charger: 3-5 hour 15. Oil level indicator 16. Handle assembly 17. Handle assembly release knob 18. Anti-kickback 19. Front guard 20. Battery release tab 21. Battery led’s 10 1 16 19 18 2 4 15 7 17 9 8 5 6 12 know your product 1. Front handle 2. Oil ...
Page 11
11 assembly prior to using the chain saw the chain and bar need to be fitted to the saw and the handle assembly requires fitting to the chainsaw housing. Prior to performing any adjustments ensure the battery has been removed from the saw to prevent any accidental starting. Handle the chain with car...
Page 12
12 2. Retighten the side cover clamp knob firmly oil filling note: the chain saw is shipped without oil in it. The chain saw must never be used without oil . Warning: always ensure that the chainsaw is switched off and the battery removed before making any adjustments. 1. Remove oil tank cap (2) and...
Page 13
13 pack to over heat. When a preset cell temperature is detected, the battery pack will automatically stop operating and will not restart until the battery pack has cooled to a safe level. In this condition, do not force-cool the pack by placing in a freezer or similar device. Refer to the “ overloa...
Page 14
14 5. Remove the battery from the charger and the charger from the mains power. The red light should go off. To obtain the best life for the battery never allow the tool to completely drain the battery and come to a complete stand still before recharging. The battery should be placed on charge whene...
Page 15
15 using the chainsaw the scope of this small pruning chain saw is for small limbs and pruning applications. This saw is not designed for heavy duty or fast cutting actions. If the saw is pushed, the overload will operate and the saw will stop. The saw will cut as specified, but is limited to small ...
Page 16
16 avoid jamming always cut into the compression wood first until the cut starts to close. Always make the compression cut beneath if the log or limb is suspended from one end, and on top if it is supported at both ends. Cut from the other side towards the compression cut. Make a habit of using a we...
Page 17
17 make sure you start your cut where limb will not pinch saw during cutting. To avoid pinching, start cut on freely hanging limbs from above limb, start cut on limbs under tension from under limb, if pinch occurs, turn saw off, lift limb, and remove saw. Cutting logs cutting a log resting on the tw...
Page 18
18 care of guide bar uneven bar wear causes most guide bar problems, incorrect sharpening of chain cutter and depth gauge settings often cause this, when bar wears unevenly, it widens guide bar groove, this causes chain clatter ad river popping. Saw will not cut straight, replaces guide bar if this ...
Page 19
19 2. Check that the lubrication system is adequate. 3. Clean the bar and sprocket area. 4. Turn the bar over everyday. 5. Check the bar wear. 6. Ensure that the oil flow hole is unobstructed. 7. Clean the chain guide on the bar. 8. Check the chain tension, sharpen the blades and check their conditi...
Page 20
20vcsg im ed6.Indd 20 28/8/13 8:03:44 am.