- DL manuals
- A-Neu Video
- Matrix Switcher
- HD-88LA
- Instruction Manual
A-Neu Video HD-88LA Instruction Manual
Summary of HD-88LA
Page 2
Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...
Page 3
1 table of contents contents package contents ...............................................................1 introduction & features ................................................. 2 specifications ....................................................................... 3 front panel ...............
Page 4
Features introduction the hd-88la is high-performance 8x8 matrix routing switcher for hdmi signals. This switcher supports data rates up to 6.75 gbps, enabling 1080p hdmi formats and uxga/wuxga/dvi resolution to any hd display. High definition digital signals can be selected and distributed to any (...
Page 5
Specifications specifications • type of hdmi switcher: 8x hdmi inputs to 8x hdmi outputs matrix switcher • hdmi support: hd 1080p@60hz, h36-bit deep color, 3d (1.4a) formats • hdcp/cec support: hdcp 2.0 compliant, cec compliant • video bandwidth: double data rates: 340mhz, total 6.75gbps bandwidth •...
Page 6
4 front panel front panel q power switch the power switch turns the unit on and off. The lcm will illuminate red to indicate that the switcher is on and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration wil...
Page 7
5 front panel front panel i function key - all disables (mute) video on all destinations or selects the same source to all destinations. Option 1 - press all followed by off button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - press all followed by sourc...
Page 8
6 front panel front panel d function key - memory the system will show store presets, up to a total of 16. Presets are stored in local memory using source keys 1 thru 8 or destination keys 1 thru 8 as the memory preset location. - configure desired matrices. - press memory button. - press 1 thru 8 o...
Page 9
7 rear panel rear panel power jack: dc jack - inner od ᴓ 2.1mm (+ ) outside od ᴓ 5.5mm (gnd) power input - 12vdc, 5a ir extender jack: female jack - inner od ᴓ 3.5 mm remote port : db-9pin female connector remote port : control the switcher rj-45 female connector ethernet port: note: the ethernet po...
Page 10
Typical application installing diagram sample connection using ir transmitters and ir receiver to control a projector via hdbaset™ transmitter and hdbaset™ receiver. Note: 1. Ir control projector over hdbaset™ extender: use hdbaset™ transmitter & hdbaset™ receiver 2. Audio input : uspport dvi audio ...
Page 11
Typical application installing diagram sample connection using dvi & audio input and link to the audio amplifier via spdif digital signal output. Note : 1. Use dvi and audio input via dvi player device. 2. Hdmi display support dvi input via hdmi hdtv support dvi input 3. Spdif output via coax cable ...
Page 12
Remote control before making any connections to the switcher. Observe the following: > ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) > ensure that the power switch is off > ensure that all system grounds (earth) are connected to a common point. > avoid powerin...
Page 13
Remote control ir remote custom and data codes (nec standard) how to setup ir codes : model number : hd-88la custom code : 38c7 power on : 38c7 a15e power off : 38c7 a25d all : 38c7 b04f off : 38c7 b14e edid : 38c7 b748 lock : 38c7 b54a recall : 38c7 b24d memory : 38c7 b44b enter : 38c7 b34c press d...
Page 14
12 ir extender note: the external ir jack has voltage on the “ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off. *** when you plug the external ir exte...
Page 15
Edid function edid function setup edid setup to change the edid setup step 1. Press the edid button the display will show the currently selected edid mode step 2. Press source #1 or #2 button row the button will flash blue and the display will show the current embedded edid status. Step 3. Press the...
Page 16
Edid function note : the already learned edid cannot be modified. You can only rebuild a new learning edid. For example: when the source has “learned” the edid data from a destination, it will save that edid information into eprom and the edid data cannot change. Please select new learning destinati...
Page 17
Edid function edid function : learning learning edid single to single example : learn destination #8 edid to source #5. Step 1. Press the edid button the button will flash blue and the display will show the current embedded edid status. Step 2. Press the destination #8 button row copy the destinatio...
Page 18
Edid function auto modedefinition common resolution and audio switcher will find highest common resolution and audio from all destination edid to link source. Example for single source destination > press #1 and then source > press #1 destination device #1 will set to the highest common resolution a...
Page 19
17 ethernet serial interface ethernet serial interface connect a pc or control system. Version compatible v2.0 for a complete list of commands, please reference external document extended ethernet protocol instruction manual. Example of the commanded string to route input 3 to output 4 output04 03; ...
Page 20
Rs-232 serial interface rs-232 serial interface connect a pc or control system. Version compatible v2.0 for a complete list of commands, please reference external document extended rs-232 protocol instruction manual. Example of the commanded string to route input 3 to output 4 output04 03; rs-232 se...
Page 21
Gui interface 1a: supports routing using lines 19.
Page 22
Gui interface 1b: supports routing using cross points 20
Page 23
Gui interface 2: select different matrix sizes 21.
Page 24
Gui interface 3: support com ports 1 thru 4 22.
Page 25
23 end of document terms and conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signi...