AAxeon FCM-3312SX User Manual
PN: 6306X3312000XXX
Trademarks
Contents subject to revision without prior notice.
All trademarks remain the property of their owners.
Copyright Statement
This publication may not be reproduced as a whole or in
part, in any way whatsoever unless prior consent has been
obtained from owner.
FCC Warning
The OPTOLINX GIGABIT MEDIA CONVERTER has
been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC
Rules. These standards are designed to provide
reasonable protection against harmful interference when
this device is operated in a commercial environment. This
device generate, use, and can radiate radio frequency
energy and may cause harmful interference to radio
communications unless installed in accordance with this
User’s Guide. Operation of this device in a residential
area is likely to cause harmful interference in which cases
the user is responsible for taking appropriate remedial
action at his/her own expense.
CE Mark Warning
This is class A products. In a domestic environment this
product may cause radio interference in which case the
user will need to consider adequate preventative
methods.
Checklist
The carton should contain the following items:
-
OPTOLINX GIGABIT MEDIA CONVERTER
-
User’s guide
Please notify your sales representative immediately if any
items are missing or damaged.
1. Overview
The OPTOLINX GIGABIT MEDIA CONVERTER is
designed to meet the massive needs for Gigabit network
deployment. This solution allows users to extend a copper
based Gigabit network via fiber cable to a maximum
distance up to 30KM.
The OPTOLINX GIGABIT MEDIA CONVERTER is fully
compliant with IEEE802.3z & 802.3ab standards. It can be
installed into a series of FCM-CHS2 Converter Chassis.
The installation & operation procedures are simple &
straightforward. Operation status can be locally monitored
through a set of Diagnostic LED located in the front panel;
or - if installed within a Management Chassis, via network
management system remotely.
Features
-
100Base-TX and IEEE 802.3ab
10/100/1000Base-TX to 1000Base-FX
Converter
-
Standard : IEEE 802.3z, 802.3ab & 802.3u
-
Store and Forward Switching Mechanism
-
Supports 256K Byte Packet Buffer
-
Supports Loop Back and Diagnostic Test
-
Interface: 1 * RJ-45 connector
1 *SX.LX Fiber Optic SC
-
MDI/MDIX Auto-Crossover supported
-
LED: Power , Status, FDX ,Speed
TP Link/ACT, FO Link /ACT
-
Plug-and-Play installation
-
Supports SNMP proxy
3. Installation
•
Remove the Converter Chassis front panel protective
plate from the selected installation slot.
•
Carefully slide the converter module into the
Converter Chassis and ensure the converter golden
finger connection with the socket, and rotate the
OPTOLINX GIGABIT MEDIA CONVERTERBTFX
bracket screw into the Converter Chassis
•
Attach fiber cable from the OPTOLINX GIGABIT
MEDIA CONVERTERBTFX fiber port to the fiber
network. The fiber connections must be matched –
transmit socket to receive socket.
•
Attach a UTP cable from the 1000Base-TX network to
the RJ-45 port on the OPTOLINX GIGABIT MEDIA
CONVERTERBTFX
•
Check if the Power LED lights up. The TP Link and FX
Link LED will both light up when all the cable
connections are satisfactory.
Gigabit TX
Fiber Transceive
r
Fig. 2 Basic Network Connection
Gigabit Fiber
Network
GIGABIT TX
Fig-1 LED, Connector and Jumper
Fiber Transceive
r
TX
FX
FDX/
COL
Fiber
Transceiver
RJ-45
Connector
.
Status
PWR
Speed
Diag