Airfonix AFX-19AR050 User manual - page 14
EN
14
www.airfonix.com
Setting Zone Codes for Your Installation
The Airfonix R and T Series are highly versatile. The six scenarios illustrated on pages 10 through 12
require corresponding zone codes that you will now set. If you have any questions please contact
Customer Service at at (888) 778-2446 or www.airfonix.com.
Before You Begin
One or Two Receivers.
•
Active or Passive Speakers.
•
NOTE: Follow the black heading for passive and the blue heading for active
speakers on the chart below.
One or Two Zones.
•
Power of Each Connected Speaker.
•
NOTE: Scenarios 1 through 3 use different codes for setup with 4 ohm
or 8 ohm speakers.
LEFT Mono, RIGHT Mono, or Stereo Channels.
•
Use the charts below to determine the correct settings for each unit:
1 Transmitter/1 Receiver 1 ZONE
Scenario 1 (4 ohm)
1 Transmitter/2 Receivers 1 ZONE
Scenario 2 (4 ohm)
1 Transmitter/2 Receivers 2 ZONES
Scenario 3 (4 ohm)
Transmitter
Receiver
Stereo
4 ohm, 25W/ch
Transmitter
Receiver
Mono LEFT
4 ohm, 50W
Receiver
Mono RIGHT
4 ohm, 50W
Transmitter
Receiver
Stereo
4 ohm, 25W/ch
Receiver
Stereo
4 ohm, 25W/ch
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
1 Transmitter/1 Receiver 1 ZONE
Scenario 1 (8 ohm)
1 Transmitter/2 Receivers 1 ZONE
Scenario 2 (8 ohm)
1 Transmitter/2 Receivers 2 ZONES
Scenario 3 (8 ohm)
Transmitter
Receiver
Stereo
8 ohm, 25W/ch
Transmitter
Receiver
mono LEFT
8 ohm, 36W
Receiver
mono RIGHT
8 ohm, 36W
Transmitter
Receiver
Stereo
8 ohm, 25W/ch
Receiver
Stereo
8 ohm, 25W/ch
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
1 Transmitter/1 Receiver 1 ZONE
Scenario 4
1 Transmitter/2 Receivers 1 ZONE
Scenario 5
1 Transmitter/2 Receivers 2 ZONES
Scenario 6
Transmitter
Receiver
Stereo
Active Speakers
Transmitter
Receiver
Mono LEFT
Active Speakers
Receiver
Mono RIGHT
Active Speakers
Transmitter
Receiver
Stereo
Active Speakers
Receiver
Stereo
Active Speakers
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
Setting
OFF
ON
IMPORTANT: Pay close attention when making these connections. The receiver set with the left channel codes
connects to your speaker using the left output connectors and the receiver set with the right channel codes connects
to your speaker using the right output connectors. The system will not work unless these connections are correct.
!
Disconnect the power from all units. Locate the three dip switches on the bottom
of each unit. Use a small flat screwdriver to push the first and second dip switches to
ON or leave in OFF position to match the code for your installation.
IMPORTANT: Do not adjust the third dip switch. Leave it in the OFF
position after pairing. The factory default position is OFF for all switches.
!
Setting
OFF
ON
Setting
OFF
ON
Use a small screwdriver to set the correct codes for each unit:
First go through the bulleted list to determine if you are using: