1. DL manuals
  2. Airlink101
  3. Wireless Router
  4. AR504
  5. Quick Installation Manual

Airlink101 AR504 Quick Installation Manual

Other manuals for AR504: User Manual
Manual is about: Airlink101 Broadband Router User's Manual

Summary of AR504

  • Page 1

    Quick installation guide model # ar504 ver. 1a.

  • Page 2

    Section 1 connect the router note: prior to connecting the router, be sure to power off your computer, dsl/cable modem, and the router. Step 1 connect one end of a network cable to the wan port of the router and connect the other end of the cable to the dsl/cable modem. Step 2 with another network c...

  • Page 3

    Section 2 verify connection to router step 1 go to start, run, type command (for windows 95/98/me) or cmd (for windows 2000/xp) and click ok. You will see the command prompt as below. Step 2 type ping 192.168.1.1 and press enter. You should get four reply responses back. Step 3 if you get request ti...

  • Page 4

    Step 5 type ipconfig/renew and press enter. You should get an ip address of 192.168.1.X (where x is a number between 2 - 254). Proceed to section 3, configure the router. If you don’t get an ip address, reset the router by holding in the reset button at the back of the router for 10 seconds while it...

  • Page 5

    Step 8 after your ip address is released, click renew. You should get an ip address of 192.168.1.X (where x is a number between 2 - 254). If you don’t get an ip address, reset the router by holding in the reset button at the back of the router for 10 seconds while it is on and try renew again. Secti...

  • Page 6

    Step 3 click on wizard from the main menu to open the setup wizard. Step 4 click next to begin the setup wizard. Step 5 select your wan type (internet connection type) and click next. If you are not sure what your internet connection type is, please contact your internet service provider (isp) for a...

  • Page 7

    Step 6 follow the steps below according to your internet connection type. Static ip fill in the applicable fields according to the information provided by your isp. Click next when done and proceed to step 7 . Cable modem if your isp has provided you with a host name, enter it in the host name field...

  • Page 8

    Road runner fill in the applicable fields according to the information provided by your isp. Click next when done and proceed to step 7 . Dsl fill in the applicable fields according to the information provided by your isp. Click next when done and proceed to step 7 . Note: depending on the isp, you ...

  • Page 9

    Pptp fill in the applicable fields according to the information provided by your isp. Click next when done and proceed to step 7 . L2tp fill in the applicable fields according to the information provided by your isp. Click next when done and proceed to step 7 ..

  • Page 10

    Step 8 click ok to confirm reboot. Step 9 wait for the router to reboot and proceed to section 4, verify connection status. Step 7 click reboot to apply your settings..

  • Page 11

    Section 4 verify connection status step 1 login to the router’s web configuration page and click on the status link from the main menu. Step 2 verify that the wan status displays valid numbers (instead of all 0’s). If you use cable modem and you see all 0’s, click on the renew button. If you use dsl...

  • Page 12

    Section 5 troubleshooting for cable modem users only step 1 go to the router’s setup wizard. Step 2 at the cable modem setting (dynamic ip address), click on the clone mac button and click next. Step 3 once you clicked the renew or connect button, you should see some numbers under wan status. This m...

  • Page 13

    For cable modem and dsl users step 1 power off the cable/dsl modem, router, and computer and wait for 5 minutes. Step 2 turn on the cable/dsl modem and wait for the lights on the modem to settle down. Step 3 turn on the router and wait for the lights on the router to settle down. Step 4 turn on the ...