1. DL manuals
  2. Airmaster
  3. Sports & Outdoors
  4. Aero bounce 120
  5. Assembly And Operating Manual

Airmaster Aero bounce 120 Assembly And Operating Manual

Manual is about: Trampoline series

Summary of Aero bounce 120

  • Page 1

    Assembly and operating manual the content in this document is subject to change without notice. © copyright mactrends international ltd 2013. All rights reserved..

  • Page 2

    Assembly and operating manual the mega bounce 140 14ft the aero bounce 120 12ft the supa bounce 100 10ft the bounce 80 8ft airmaster advises that the use of this trampoline and or any accessory product is considered a high intensity activity which could result in injury. By purchasing this product a...

  • Page 3

    1. General instructions 1.1 purpose ► the product is intended for home/domestic use only and is not suitable for professional uses. ► please refer to the maximum weight as per specification sheet. Overloading the trampoline above the recommended user weight will cause damage which is not covered by ...

  • Page 4

    Warning - when in use 1. Please ensure that the safety enclosure net zipper is 100% closed and that all three entrance hooks are connected before jumping. 2. Users must not intentionally jump into the safety net; it is designed to stop persons from falling from the trampoline but not for intentional...

  • Page 5

    3. Maintenance instructions ► as previously stated in the safety section it is vital that the trampoline is checked regularly, at least once a month and more often if under sustained use. Special attention should be paid to the nut, bolt and washer assemblies making sure that they are firmly tight. ...

  • Page 6

    1 3 5 2 3 16 15 10 9 8 6 airmaster trampoline parts list 4 7 17 14 18 21 20 19 22 23 11 13 24 25 12.

  • Page 7

    Box #1 no. Parts name parts code and size for 8ft qty parts code and size for 10ft qty parts code and size for 12ft qty parts code and size for 14ft qty picture p-otp04a1-08- tr p-otp04a1-10- tr p-otp04a1-12- tr p-otp04a1-14- tr Ф38*1.5 *1307mm Ф38*1.5 *1232mm Ф42*1.5 *1470mm Ф42*1.5 *1710mm p-otp04...

  • Page 8

    P-otp04a1-ps- sm p-otp04a1-ps- sm 1920mm 1920mm p-otp04a1-up p-otp04a1-up Ф25*1.2 935mm Ф25*1.2 935mm p-otp04a1-mp p-otp04a1-mp Ф25*1.2 935mm Ф25*1.2 935mm p-otp04a1-lp p-otp04a1-lp Ф25*1.2 272mm Ф25*1.2 272mm p-otp04a1-08- sm p-otp04a1-10- sm p-otp04a1-12- sm p-otp04a1-14- sm d2440mm d3050mm d3660m...

  • Page 9

    Box #2 no. Parts name parts code and size for 8ft qty parts code and size for 10ft qty parts code and size for 12ft qty parts code and size for 14ft qty picture p-otp04a1-12- sp p-otp04a1-14- sp 177mm 177mm p-otp04a1- bh-lp p-otp04a1- bh-lp Ф38*1.5 733mm Ф38*1.5 733mm p-otp04a1- bh-mp p-otp04a1- bh-...

  • Page 10

    P-otp04a1-12- tb-p1 p-otp04a1-14- tb-p1 210*100mm 210*100mm parts name parts code and size for 8ft qty parts code and size for 10ft qty parts code and size for 12ft qty parts code and size for 14ft qty picture screw m6*77 p-otp04a1- sw-m6-77 10 p-otp04a1- sw-m6-77 14 p-otp04a1- sw-m6-77 14 p-otp04a1...

  • Page 11

    Parts name parts code and size for 8ft qty parts code and size for 10ft qty parts code and size for 12ft qty parts code and size for 14ft qty picture nuts p-otp04a1-nt 6 p-otp04a1-nt 6 p-otp04a1-nt 6 p-otp04a1-nt 6 m6 plastic caps p-otp04a1-pc- m6 5 p-otp04a1-pc- m6 5 p-otp04a1-pc- m6 5 p-otp04a1-pc...

  • Page 12

    3 4 1 select a top rail. Continue to assemble all the top rails into pairs as shown. 2 connect two top rails together. • note: please refer to the parts list for quantity of parts you are assembling as they can vary from model to model. 7 8 connect the two legs to each foot as shown. 5 6 locate the ...

  • Page 13

    9 10 11 12 take an assembled foot and leg assembly. And connect with a pair of connected top rails. 13 14 15 16 take two assembled top rail/foot and leg units, turnover and connect together. The connected pairs should stand up unsupported. Continue connecting the rest of the sections together. • not...

  • Page 14

    17 18 when joining the final two sections to form a circle, it helps to anchor your leg against the trampoline leg vertically below the connection. This will provide extra leverage, making it easier to line up and slide the two joints together. 19 the completed frame should appear as shown above. • ...

  • Page 15

    22 23 after you have connected the first spring to the frame walk around to the opposite side of the frame matching each d-ring to a matching slot as you walk (this will ensure that you will not have to disconnect and refit springs later on in this exercise). Once at the other side of the frame atta...

  • Page 16

    26 27 select one each of a safety net lower and upper pole and fit together. Note the 2 poles can easily be distinguished as the upper pole has a plastic cap on the top. The lower pole does not have this plastic cap. 30 31 take a sleeve. Slide the open end over the top of the curved pole (plastic ca...

  • Page 17

    34 35 take one assembled safety pole and attach to the frame with the nuts and bolts supplied. In the process place the plastic spacers as supplied between the saftey pole and the frame. Connect the now completed curved safety net poles to the trampoline as shown above. 6 36 attach the basketball ho...

  • Page 18

    7 40 slide one of the assembled fibreglass rods halfway around the safety net hem -until each end is just showing. Repeat the same exercise with the second rod however in this instance ensure that the end being pushed through the hem is the opposite end of the rod already pushed through on the other...

  • Page 19

    8 • very important note: make sure when attaching the net pockets onto the safety net pole, that the saftey net is not twisted by attaching the pocket to the safety net pole either to the left or right of the one it should be on. As a point of reference the net opening zip should be running perfectl...

  • Page 20

    9 51 52 move to the back of the trampoline to position 2, (opposite side to the zip entrance). Slide a metal d-ring through the slit in the safety net seam and attach a spring connecting the jumping mat and frame in the same manner as before. 53 54 move to positions 3 and 4 repeating the process. To...

  • Page 21

    10 55 56 now repeat the same exercise for positions 5 through 8. Once completed attach the remainder of the springs in the manner already described and use the spring attachment tool as required. As a reminder make sure the each d-ring is correctly positioned with the long edge fitted flush in its r...

  • Page 22: Baske

    Baske 1. Place th firm the 2. Place th correspo 3. Attach holder, nut m5 etball he correspond e support pole he hoop hold onding holes the basketb screw the b x 1. Hoop ding bolts (the e. Der (metal p on the front p ball hoop on bolt m575mm set as e m812mm x plate) and sc plate nto the hoo m x 1 in,...

  • Page 23

    5. Screw t plate. 7. You nea the bolt m arly finish… 8100mm in to the met tal 6. Put scre 8. Plac finis the other s ew the nut m ce the netting shed! Pring onto t 8 in. G and velcro the bolt m8 it onto the h 8, and hoop..

  • Page 24: You Are Now Finished

    11 you are now finished enjoy the mega bounce 140 14ft the aero bounce 120 12ft the supa bounce 100 10ft the bounce 80 8ft.