Airmux-200 installation and operation manual point-to-point wireless tdm/ip multiplexer.
Airmux-200 point-to-point wireless tdm/ip multiplexer installation and operation manual notice this manual contains information that is proprietary to rad data communications ltd. ("rad"). No part of this publication may be reproduced in any form whatsoever without prior written approval by rad data...
Limited warranty rad warrants to distributor that the hardware in the airmux-200 to be delivered hereunder shall be free of defects in material and workmanship under normal use and service for a period of twelve (12) months following the date of shipment to distributor. If, during the warranty perio...
General safety instructions the following instructions serve as a general guide for the safe installation and operation of telecommunications products. Additional instructions, if applicable, are included inside the manual. Safety symbols this symbol may appear on the equipment or in the text. It in...
Handling energized products general safety practices do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the off position or a fuse is blown. For dc-powered products, altho...
Installing the outdoor units (odus) observe the following safety measures when installing the outdoor units. • masts/poles should comply with local standards. • only trained professional installers should install or dismantle outdoor units. The installer is responsible for meeting all building and s...
Connection of data and telecommunications cables data and telecommunication interfaces are classified according to their safety status. The following table lists the status of several standard interfaces. If the status of a given port differs from the standard one, a notice will be given in the manu...
To reduce the risk of fire, use only no. 26 awg or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunications 26 awg ou de section supérieure. Some ports are suitable for connection to intra-building or non-exposed wiring or cab...
-- connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance (rad) could void t...
Installing airmux-200 units 1 quick start guide installation of airmux-200 should be carried out only by a qualified technician. If you are familiar with airmux-200, use this guide to prepare the units for operation. 1. Installing airmux-200 units equipment required: • rj-45 crimp tool (if pre-assem...
Quick start guide airmux-200 installation and operation manual 2 installing airmux-200 units 5. Connect the rj-45 connectors to both ends of the cable, use the pinout table and diagram below: idu rj-45 wire color function odu rj-45 1 white/green ethernet (rxn) 1 2 green ethernet (rxt) 2 3 white/oran...
Airmux-200 installation and operation manual quick start guide installing airmux-200 units 3 do not stand in front of a live outdoor unit. 3. Align the site a odu in the direction of the site b odu. 4. Connect power to the site b idu. After approximately 20 seconds the odu beeper starts beeping, thi...
Quick start guide airmux-200 installation and operation manual 4 installing airmux-200 units 15. After selection of the radio channel and the link rate (as determined in the link budget calculator utility), verify that the link quality bar in the airmux manager is within the green range for tdm serv...
Installation and operation manual i contents chapter 1. Introduction 1.1 overview..................................................................................................................... 1-1 application ........................................................................................
Table of contents ii airmux-200 installation and operation manual chapter 5. Diagnostics and troubleshooting 5.1 error detection and alarms.......................................................................................... 5-1 5.2 collecting and saving statistics.................................
Table of contents installation and operation manual iii 5-1. Preferences dialog box, event log tab.................................................................................. 5-3 5-2. Loopbacks dialog box.............................................................................................
Table of contents iv airmux-200 installation and operation manual.
Overview 1-1 chapter 1 introduction 1.1 overview airmux-200 is a carrier-class, high capacity, point-to-point broadband wireless transmission system. Airmux-200 combines legacy tdm and ethernet services over 5.725–5.850 ghz license-exempt bands and is suitable for deployment in fcc, esti, or can reg...
Chapter 1 introduction airmux-200 installation and operation manual 1-2 overview table 1-1 explains the possible combinations of airmux-200 and gives typical ranges according to supported data rates. Table 1-1. Airmux-200 throughput air-interface rate [mbps] throughput full duplex [mbps] throughput ...
Airmux-200 installation and operation manual chapter 1 introduction physical description 1-3 1.2 physical description airmux-200 system consists of an outdoor unit (odu) and an indoor unit (idu). Figure 1-2 illustrates an airmux-200 unit assembly. Figure 1-2. Airmux-200 unit with integrated antenna ...
Chapter 1 introduction airmux-200 installation and operation manual 1-4 technical specifications 1.3 technical specifications air-interface technology ofdm frequency band 5.725–5.850 ghz, ism duplexing method time division duplex (tdd) capacity configurable up to 48 mbps (see table 1-1 ) modulation ...
Airmux-200 installation and operation manual chapter 1 introduction technical specifications 1-5 indicators pwr (green) power status idu (green) idu status odu (green/red) odu-to-idu link status air i/f (green/red) air interface status service (green/red) e1/t1 signal status power source 100–240 vac...
Chapter 1 introduction airmux-200 installation and operation manual 1-6 technical specifications.
Airmux-200 system 2-1 chapter 2 installation and setup this chapter describes installation and setup procedures for airmux-200 system. After installing the unit, refer to chapter 3 for configuration instructions and chapter 4 for operation instructions. In case a problem is encountered, refer to cha...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-2 package contents 2.2 site requirements and prerequisites for the idu, allow at least 90 cm (36 in) of frontal clearance for operating and maintenance accessibility. Allow at least 10 cm (4 in) clearance at the rear of ...
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-3 2.4 equipment required the following is a list of the equipment required for installing the airmux-200 hardware. • rj-45 crimp tool (if pre-assembled odu/idu cable is not used) • drill (for wall ...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-4 installation and setup figure 2-1 illustrates a typical installation of airmux-200 with an external antenna. Figure 2-1. Typical installation diagram mounting the odu the odu is the transmitting and receiving element o...
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-5 prior to connecting cables to the odu, the protective earth terminal (screw) of the odu must be connected to an external protective ground conductor or to a grounded mast. Only a qualified person...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-6 installation and setup installing airmux-200 management software airmux-200 management application is distributed on cd-rom as an executable file. The application has the following pc requirements: • memory: 128 mb ram...
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-7 starting the airmux manager software to start airmux manager: 1. Connect the management station to the lan. 2. Double-click the airmux manager icon on the desktop, or from the start menu, point t...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-8 installation and setup figure 2-4. Main menu aligning the airmux-200 odus perform the airmux-200 odu alignment using the beepers located inside the odus. To speed up the installation time, alignment of an airmux-200 li...
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-9 beeper sequence =beeper on =beeper off description [approx. 1s] best signal so far signal quality increased no change in signal signal quality decreased [approx. 2s] no air link figure 2-5. Beepe...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-10 installation and setup figure 2-6. Link installation wizard 3. Click next to proceed with the installation procedure. The system dialog box opens (see figure 2-7 ).
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-11 figure 2-7. Installation wizard, system dialog box 4. Enter a ssid (system id). The ssid must include at least eight alphanumeric characters. Up to 24 characters are allowed. • both sites of a l...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-12 installation and setup quality bars figure 2-8. Installation wizard, channel select dialog box 9. Select the required operating channel. The pull down list shows the ism frequencies available. The manual option allows...
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-13 figure 2-9. Installation wizard, rates dialog box 11. Select a suitable air interface rate according to the services required. Table 1-1 lists throughput rates and capacities. 12. Click evaluate...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-14 installation and setup figure 2-10. Installation wizard, services dialog box 15. In the service dialog box, select one of the following: e1/t1 – select the e1/t1 field, if you intend to transmit e1/t1 data and etherne...
Airmux-200 installation and operation manual chapter 2 installation and setup installation and setup 2-15 figure 2-11. Installation wizard, finish screen 17. Click finish to complete the installation wizard. When the wireless link is established between the site a and site b units, the link status i...
Chapter 2 installation and setup airmux-200 installation and operation manual 2-16 installation and setup.