1. DL manuals
  2. Airsight
  3. IP Camera
  4. XX39A
  5. User Manual

Airsight XX39A User Manual

Other manuals for XX39A: User Manual, Quick Installation Manual
Manual is about: Indoor Wireless/Wired IP Network Camera (with H.264 image compression)

Summary of XX39A

  • Page 1

    Indoor wireless/wired ip network camera (with h.264 image compression) model xx39a user manual.

  • Page 2

    2 contents 1. Introduction ........................................................................................................................................ 3 1.1 features ............................................................................................................................

  • Page 3: 1. Introduction

    3 1. Introduction important notice the various screens throughout this owner’s manual will look different depending on the browser you use. Full functionality is available when using internet explorer (ie) with activex (ocx) installed. Limited functionality is available with other browsers, such as ...

  • Page 4

    4 1.1 features ☆ powerful high-speed video protocol processor ☆ high-sensitivity 1/4’’ cmos sensor ☆ picture total 300k pixels ☆ supports pan and tilt (pt) control, pan 320°, tilt 120° ☆ optimized h.264 mjpeg video compression for transmission ☆ multi-level user management and passwords definition ☆...

  • Page 5

    5 1.3 product views 1.3.1 rear view 1.3.2 bottom view.

  • Page 6

    6 1.4 pc system requirements system configuration requirements: cpu: 2.06 ghz or above. Memory : 256m or above. Network card: 10m or above. Display card : 64m or above memory. Recommended operating system: windows xp, windows vista, windows 7. 1.5 hardware installation follow the steps below to set ...

  • Page 7

    7 2. Installation and settings system requirement : operating system: windows 2000 / xp / vista / 7 network protocol: tcp/ip network structure: applies to all network connections 10/100m lan platform browser: internet explorer 6.0 or above. Firefox, google, safari, or chrome. 2.1 network connection ...

  • Page 8

    8 figure 1.2 2.2 browser settings (for ie only) ocx will be downloaded automatically when you login to the ip camera, but you might have to set the ie browser to enable the ocx to be downloaded automatically after signing in. Steps as below: 1. Close the firewall of your computer. 2. Change the acti...

  • Page 9

    9 figure 1.4 you can also click “start” menu->“internet explorer”, and choose “internet attributes”, or via “control panel ” ->“internet explorer”, to access security settings. Note : make sure that your firewall or anti-virus software doesn’t block the software or activex. If you couldn’t see live ...

  • Page 10

    10 2.4 ipcam ip address search tool (for ie browser only) step 1: use tool “searchipcam.Exe” to find ip address of lan. Figure 1.5 step 2: double click “search ipcam” on your desktop, the camera’s ip & mac address will be displayed. If you want to search again, click “search”. Figure 1.6 step 3: dou...

  • Page 11

    11 figure 1.7 2.5 install the ocx activex (for ie only) install the ocx activex for the first time login; click the icon on the right bottom, download the ocx file, then double click to install it automatically. After ocx installed fully, then input the user name and password to login the camera. 2....

  • Page 12

    12 figure 1.8.

  • Page 13: 3. Software Operation

    13 3. Software operation 3.1 software operation for ie browser choose your desired language, input correct user name and password, then click “login” user name : admin password: leave blank, i.E. No password. Figure 1.9 choose languages here for mobile phone login for ocx installation (ie only) clic...

  • Page 14

    14 3.2 software operation for chrome, firefox, safari: choose the suitable language, input correct user name and password, then click “login” user name : admin password: leave blank, i.E. No password. Figure 2.1 choose the login mode. Quicktime : choose quicktime, login to the camera directly. If th...

  • Page 15

    15 choose languages here for mobile phone login click to login using other browsers (excluding ie). Figure 2.3 3.1 functions 3.1.1 three main functions (for ie): figure 2.4 live video: click it, back to live video window from “playback” or “params settings” playback： click to query and playback the ...

  • Page 16

    16 3.1.2 two main functions (for safari, chrome, firefox) figure 2.5 live video: click it, back to live video window from “playback” or “params settings” params settings： setting the camera’s parameters (details see 4 params settings) 3.2 for live video (for ie browser) 3.2.1 top menu: figure 2.6 pl...

  • Page 17

    17 clear alarm: click to stop the alarm manually when there is an alarm triggered, and pop-up prompt as below: figure 2.8 osd settings: click it will pop-up the osd settings interface, including osd color, frequency, image mirror and flip. Figure 2.9 osd: means “on-screen display” osd color: includi...

  • Page 18

    18 figure 3.1 mirror and flip mirror : select this checkbox to see a mirror image. Uncheck it to go back to normal. Flip : select this checkbox to flip the image upside down. Uncheck it to go back to normal. Figure 3.2 note : you can choose mirror and flip function if you set up the camera in a spec...

  • Page 19

    19 figure 3.4 osd: means “on-screen display” osd color: including disabled, black, red, green, blue, purple, gray, silver, yellow, olive, turquoise, white, light blue etc. Figure 3.5 frequency: including 50hz, 60hz, outdoor. 50hz/60hz for the users who use 50hz/60hz frequency, outdoor for the users ...

  • Page 20

    20 figure 3.7 note : you can choose mirror and flip function if you set up the camera in a special position, upside down for example. 3.3.2 top menu for vlc mode: figure 3.8 adaptive size of the display. Click it, will get adaptive size the true size of the display. Click it, will back to the true s...

  • Page 21

    21 figure 3.9 pt control: set pan/tilt as upward, downward, leftward, rightward, up-left, down-left, up-right, down-right, etc directions. Center: click this icon, the camera will pan/tilt, then stop at the center. Normally it will rotate 1 rotation. Up: click this icon, camera will move up, you can...

  • Page 22

    22 cruise: preset cruise, camera can cruise according to the different presets you set. Click this icon, the camera will rotate up and down, i.E., vertical tilt, click to stop it click this icon, the camera will rotate left and right, i.E., horizontal pan, click to stop it click this icon, io output...

  • Page 23

    23 figure 4.3 there are 9 icons at the bottom of the user interface which show the status of each channel of the camera. Gray color: means there is no device connected to the main device from this channel. Green color: means the device is connected for this channel, and it works ok. Red color: means...

  • Page 24

    24 figure 4.5 set preset: it supports 9 preset positions. First, control the camera to rotate to the special position you need to set, click set preset button it will pop-up a dialog frame (figure 4.5), choose any number (1-9). Call preset: it supports 9 preset positions. If you want to monitor an i...

  • Page 25: 4. Params Settings

    25 4. Params settings 4.1 device info. Click “params settings” icon select “device info”, it will show the basic information such as “device id ”, “device client”, “device host”, “description”, “ip address”, “upnp status”, “ddns status” etc. Default device name is “ip camera”, users can change the c...

  • Page 26

    26 4.2 video info. Click “video info” to enter the interface as below: 4.2.1 for ie, camera will show as below: figure 4.9 4.2.2 for safari, chrome, firefox, camera will show as below: figure 5.0

  • Page 27

    27 there are two options for stream, main-stream and sub-stream, you can set the stream based on the actual operation environment, for example, if the bandwidth is good enough, set main-stream as initial-stream, or choose sub-stream if better. Set the parameters of main-stream and sub-stream as belo...

  • Page 28

    28 for ie, camera will show as below: figure 5.3 for safari, chrome, firefox, camera will show as below: figure 5.4 note : when the device runs, only can select bit rate or image quality either. 4.3 audio settings click “audio settings” to enter the interface: 4.3.1 for ie, camera will show as below...

  • Page 29

    29 4.3.2 for safari, chrome, firefox, camera will show as below: figure 5.6 built-in headset : choose built-in mic as the audio input device. External headset : choose external headset as the audio input device. 4.4 motion detection ● alarm output: select it to enable alarm output, unselect to stop....

  • Page 30

    30 motion detection zone armed : can set all zones to be armed, or a specified zone armed. Before setting a specified zone, you should set "motion detection" to "on", then press left mouse, drag the mouse onto video area to set the detection zone, and save it, supports 3 areas. Figure 5.8 ● detect a...

  • Page 31

    31 figure 6.1 action with alarm these are actions optional for motion detection. Figure 6.2 4.4.2 motion detection settings for safari, chrome, firefox: click “motion detection” to enter the interface: figure 6.3 ● motion detection: set motion detection armed function on/off..

  • Page 32

    32 figure 6.4 ● sensitivity: set detection sensitivity as low, middle, high, higher, highest. Figure 6.5 ● alarm duration: set each alarm duration, can be forever, 5s, 10s, 15s, 30s, 60s. Figure 6.6 linkage with alarm these are actions optional for motion detection. Figure 6.7.

  • Page 33

    33 4.5 alarm settings alarm output : select it to enable alarm output, unselect to stop. Sd-card record : select it to enable record to sd card, unselect to stop. Send e-mail : select it to enable e-mail alert function, unselect to stop. (mail service details see 4.14). Ftp upload : select it to ena...

  • Page 34

    34 figure 7.0 ● lose sd-card alarm: set alarm triggered on/off if the sd-card is lost. Figure 7.1 ● alarm input: set alarm input on/off, it supports no/nc external alarm device, choose the correct mode to make sure it works well, it refers to the i/o pin6 (input2) and pin7 (input1). Figure 7.2 ● act...

  • Page 35

    35 4.5.2 alarm settings for safari, chrome, firefox click ”alarm” to enter the interface: figure 7.4 ● external alarm: set external alarm function on/off. Figure 7.5 ● alarm duration: set external alarm output duration (relay close time), can be forever, 5s, 10s, 15s, 30s, 60s. Figure 7.6.

  • Page 36

    36 ● lose sd-card alarm: set alarm triggered on/off if the sd-card is lost (removed). Figure 7.7 ● alarm input: set alarm input on/off, it supports no/nc external alarm device, choose the correct mode to make sure it works well, it refers to the i/o pin6 (input2) and pin7 (input1). Figure 7.8 ● acti...

  • Page 37

    37 4.6.1 for ie, camera will show as below: figure 8.0 4.6.2 for safari, chrome, firefox, camera will show as below: figure 8.1 network type : there are three modes: static address, dhcp, pppoe ..

  • Page 38

    38 for ie, camera will show as below: figure 8.2 for safari, chrome, firefox, camera will show as below: figure 8.3 4.6.1 static address set network parameters manually 4.6.1.1 for ie, camera will show as below: figure 8.4.

  • Page 39

    39 4.6.1.2 for safari, chrome, firefox, camera will show as below: figure 8.5 4.6.2 dhcp choose dhcp, the camera will get ip address automatically. 4.6.2.1 for ie, camera will show as below: figure 8.6 4.6.2.2 for safari, chrome, firefox, camera will show as below: figure 8.7.

  • Page 40

    40 ● media port: default is 38401. ● web port: default is 80. ● mobile port: default is 2012. ● rtsp port: default is 554. Note: don’t change the media port, web port, mobile port, rtsp port if not necessary. 4.6.3 pppoe set parameters here to enable pppoe function. 4.6.3.1 for ie, camera will show ...

  • Page 41

    41 ● media port: default is 38401. ● web port: default is 80. ● mobile port: default is 2012. ● rtsp port: default is 554. ● enable pppoe: choose open to enable pppoe function. ● pppoe user: the account provided by isp ● pppoe password: the password provided by isp. ● pppoe ip addr. If pppoe dial-up...

  • Page 42

    42 figure 9.2 figure 9.3 if you don’t know the dns server, you can set it the same as gateway..

  • Page 43

    43 4.6.4 ddns: enable ddns function. 4.6.4.1 for ie, camera will show as below: figure 9.4 4.6.4.2 for safari, chrome, firefox, camera will show as below: figure 9.5 there are 2 options: factory ddns : this domain is provided by the manufacturer. Third party ddns : this domain is provided by a 3rd p...

  • Page 44

    44 4.7 wireless lan settings click ”wireless lan settings” to enter the interface: 4.7.1 for ie, camera will show as below: figure 9.6 4.7.2 for safari, chrome, firefox, camera will show as below: figure 9.7.

  • Page 45

    45 click the icon “search” to scan the wireless network in this environment automatically. Using wireless lan : set wi-fi on/off. Ssid : the id of wireless network, it should be the same ssid as the connected wi-fi router. Network type : two modes: 1. Infra (infrastructure mode), if using normal ap,...

  • Page 46

    46 4.9 ptz settings click “ptz settings” to enter the interface: 4.9.1 for ie, camera will show as below: figure 10.0 4.9.2 for safari, chrome, firefox, camera will show as below: figure 10.1.

  • Page 47

    47 ptz settings means once external pan tilt connected to the device, should set the camera’s rs485 communicate protocol the same as the pan tilt, then could control the ptz remotely. Protocol : support pelco-d pelco-p ptzdscp lilin minking. Baud rate : support 1200, 2400, 4800, 9600, 19200. Address...

  • Page 48

    48 4.10.2 for safari, chrome, firefox, camera will show as below: figure 10.3 every camera supports 16 users, and every user can be divided into three grades including super administrator , administrator, operator, visitor. Click add, will pop-up the window as below: for ie, camera will show as belo...

  • Page 49

    49 4.11 log click “log” to enter the interface: 4.11.1 for ie, camera will show as below: figure 10.5 4.11.2 for safari, chrome, firefox, camera will show as below: figure 10.6 record user information, including account, date, time, visitor ip address etc..

  • Page 50

    50 4.12 date time settings click “date time settings” to enter the interface: 4.12.1 for ie, camera will show as below: figure 10.7 4.12.2 for safari, chrome, firefox, camera will show as below: figure 10.8 date time : display the current date and time time zone : set the current time zone time mode...

  • Page 51

    51 for ie, camera will show as below : figure 10.9 for safari, chrome, firefox, camera will show as below: figure 11.0 ntp server : choose the relevant ntp sever when set time mode as ntp time. 4.13 multi-device settings for ie browser note: multi-device only can be set under ie browser, for firefox...

  • Page 52

    52 click search, all the cameras connected in the lan will be listed, then select a number from the bottom window, click edit, will pop-up a parameter settings window: figure 11.2 choose the id, input host, web port, media port, username, and password manually, click ok to submit. 4.14 mail service ...

  • Page 53

    53 4.14.2 for safari, chrome, firefox, camera will show as below: figure 11.4 enable smtp : set e-mail function on/off. Addresser : set sender’s name. Outbox : set sender’s email address. Inbox : set receiver’s email box. (supports 3 emails simultaneously) add email address delete email address whic...

  • Page 54

    54 4.15 ftp service settings set ftp service, snapshots will be delivered to appointed ftp server when alarmed. Click “ftp service settings” to enter the interface: 4.15.1 for ie, camera will show as below: figure 11.5 4.15.2 for safari, chrome, firefox, camera will show as below: figure 11.6.

  • Page 55

    55 enable ftp : set ftp function on/off. Ftp server : set ftp server address. Ftp port : set the port of ftp server, default is 21. Ftp user : set the user name of ftp server. Ftp password : set the password of ftp server. Upload folder : set the path of remote ftp server. Make sure that the folder ...

  • Page 56

    56 4.16.2 for safari, chrome, firefox, camera will show as below: figure 11.8 device name : display the name of sd card. Total size : display the total size of sd card free space/available space : display the free space of sd card state : display the state of sd card. Format: click it to delete all ...

  • Page 57

    57 4.17 local settings for ie browser note: local settings shows under ie activex mode only. Click “local settings” to enter the interface: figure 11.9 enable alarm audio : set audio on/off once alarmed. Enable alarm rec : set alarm record function on/off. Alarm rec time : set alarm record duration ...

  • Page 58

    58 4.18.2 for safari, chrome, firefox, camera will show as below: figure 12.1 ● reboot device: click to reboot the camera. ● restore factory settings: click it, all the parameters will be set back to factory settings. ● upgrade device firmware: click “browse/choose file”, choose the correct system f...

  • Page 59

    59 5. Playback for ie browser only note: playback function shows under ie activex mode only. Click login the playback interface, this is for sd card files playback. Figure 12.2 click search icon, will pop-up a window for search file, set the mode or time, click ok to submit, then all the correlative...

  • Page 60

    60 search mode : there are 4 search modes optional. Figure 12.4 1. Type : means search by the file type. Figure 12.5 2. Time : means search by the appointed record time figure 12.6 3. Type and time : means search by both file type and appointed record time. 4. All : means all the files. After search...

  • Page 61

    61 to start replay. Users can check the replay file information here, do other operation such as stop, pause , previous, next, fast backward, fast forward etc. Figure 12.7 image enlarge and reduce during playback, users can enlarge the image to see the video details, it supports 2x, 4x, 8x zoom. Cli...

  • Page 62

    62 6. Frequently asked questions 1. I have forgotten the administrator username and/or password there is a [rst] button on the rear panel, keep the power on, hold the reset button for 30 seconds, it will restore back to factory default settings as below: username : admin password : none, i.E. No pas...

  • Page 63

    63 solution : modify the physical address of ip camera. Possible reason 5 : web port has been modified. Solution : contact as network administrator to obtain related information. Possible reason 6 : unknown. Solution : press reset to restore to factory settings then connect it again, the default ip ...

  • Page 64

    64 note: if you are unable to do it, it means your directx is not installed properly or hardware doesn't support this function. 9. Fail to use ddns possible reason 1 : the pc or ip camera can’t connect to the internet. Solution : check the internet connection and settings. Possible reason 2 : port f...

  • Page 65

    65 fill in the web port, for example port 85, ip address as 192.168.1.100, click save. (1) repeat step 3 above, it will pop-up the window again, fill in the media port as 38401, ip address as 192.168.1.100, then save. (2) then check the “device info” –“ddns status”, it will show ddns: http://test.Ai...

  • Page 66

    66 figure 13.3.

  • Page 67: 7. Specifications

    67 7. Specifications image sensor image sensor 1/4" color cmos sensor display resolution 640 x 480 pixels (300k pixels) lens f: 6 mm, f:2.0 (ir lens) mini. Illumination 0.5 lux viewing angle 60 degree audio input built-in microphone/1 channel audio input output 1 channel audio output audio compressi...

  • Page 68

    68 8. Obtaining technical support we hope your experience with your ip network camera is enjoyable, but if you experience any issues or have any questions that this user's guide has not answered, please visit www.X10.Com/support, e-mail support@x10.Com or call 1-800-442-5065. If your camera does not...