Anthem Integrated 2 Owner's Manual - page 3
- IN TIME
all audio electronic products, the ultimate sonic
er of the Integrated 2 will not be realized until and
the unit receives a minimum of approximately 70
of signal break-in time (i.e. the Integrated 2 is on
tputting a signal).
MENT FOR PR OPE R VE NTILAT I O N
t least 4” (15 cm) of clear space above the
ted 2 chassis for proper ventilation, making sure the
slots in the chassis cover remain unobstructed.
e sure that the Integrated 2 is placed on a secure,
nd level surface (not on carpet).
Y INSTRUCTIONS
ation - Although your Integrated 2 generates only nom-
t in use, be sure that the ventilation slots in the top
ave at least 4” of unobstructed air space above them.
er and Moisture - This product should not be used
w a t e r. To prevent fire or shock hazard, do not expose
duct to rain or moisture.
- This product should be situated away from heat
s such as radiators, heat registers, stoves, or other
ces which produce heat.
er Sources - This product should be connected to an
wer source of the proper rated voltage. The original
g container will stipulate the AC voltage this unit can
e with correctly.
ning - A regular dusting with a soft, non-abrasive
ll generally keep the finish of the faceplate and chas-
ing like new. At no time should you allow any liquid to
n contact with the Integrated 2; it may run into the
nic circuitry and cause damage which will not be cov-
der your warranty.
cing - Do not open this product. No user serviceable
side. Refer servicing to an authorized service technician.
Use Periods - The power cord of this product should
ugged from the outlet when left unused for an
ed period of time.
ot remove the Integrated 2 cover while the unit is
connected to an AC power source. Cover screws
all through the ventilation slots and cause electrical
e to the Integrated 2.
PACKING MAT E R I A L S
Please retain all of the packing material and shipping boxes
for your Integrated 2. They are custom designed to prevent
shipping damage from occurring. Sonic Frontiers, Inc. will
accept no responsibility for any damage occurring to an
Integrated 2 that is shipped in packing material other than
the original Sonic Frontiers packing material.
DISC LAIME R OF L IABILITY
Under no circumstances does Sonic Frontiers, Inc.
assume liability or responsibility for injury or damages
sustained in the use or operation of this equipment or for
damages to any other equipment connected to it.
Sonic Frontiers, Inc. reserves the right to make design
changes or improvements without the obligation to revise
prior versions. All specifications are subject to change
without notice.
LIMITED FIVE YEAR W A R R A N T Y
Sonic Frontiers, Inc. warrants to the purchaser that each
Integrated 2 is free of manufacturing defects for a period
of five (5) years from the date of purchase. This five (5)
year limited non-transferable warranty excludes all vacuum
tubes, which we warrant for a period of twelve (12)
months. To receive this warranty, the original purchaser
must complete and mail to Sonic Frontiers, within thirty
(30) days from the date of purchase, the enclosed
Warranty Registration Card. Sonic Frontiers, Inc. will then
validate the warranty to the original purchaser. This war-
ranty is subject to the following conditions and limitations:
1. Warranty applies only to the original purchaser.
2. This warranty is void and inapplicable if the product has
been handled other than in accordance with the instruc-
tions in this Operating Manual, abused or misused, dam-
aged by accident, neglect or in being transported, or the
defect is due to the product being tampered with, modi-
fied or repaired by anyone other than Sonic Frontiers, Inc.
or an authorized Sonic Frontiers repair depot.
3. Warranty does not cover normal maintenance.
A
SELECT OR SWITCH
This knob is rotated to select a Line Level Input (P).
The Selector Switch is bypassed when the Tape/EPL
(External Processor Loop) mode is selected by
depressing the Tape/EPL-Source button (F), or when
SSP mode is selected by depressing the SSP button (D).
B
BALANCE CONTROL
This knob controls the relative balance of the left and
right channels to compensate for any discrepancies
caused by speaker placement, source imbalance, etc.
Full rotation to the left or right of the center detent will
fully attenuate the left or right channel.
C
VOL UME C ONTROL
This knob allows variable control over the Integrated 2’s
output level. Turn it clockwise and the music gets louder!
D -
SSP (SURROUND SOUND PROCESSOR) INPUT BUTTON
This button selects an external Surround Sound Processor
(SSP) input signal. When selected all preamp functions
are completely disabled. The only way to deselect SSP
mode is to press the SSP button a second time.*
E
HEADPHONE INPU T J ACK
The Headphone Jack accepts 1/4” stereo headphone
plugs. Upon insertion of the headphone plug, the main
amplifier outputs are disabled. All other preamp func-
tions remain operational. Removal of the headphone
plug restores the main output signal.
F
TAPE /EPL (EXTERNAL PROC ESSOR LO OP)-
SO URC E BUTTON
When this button is in the SOURCE position (button is
not depressed) the signal is routed through the
Selector Switch (A) to the Tape/EPL Output (N).
Listening and taping is done in this mode. When the
button is depressed, the source signal is taken from a
tape or processor source through the Tape/EPL Inputs
(O) bypassing the selector switch.
G
INFRA RED RE CEIVER
The Infra Red signal from the Integrated 2’s remo
control is received here, to operate the Volume, M
and SSP controls.
H
L E D
When the LED is lit the Integrated 2 is “ON”, rece
power.
When the Power Button (K) is depressed the LED
be dimly lit Green. After the power-up delay has
timed-out (approx. 40 seconds) the LED will be li
bright green. Upon activating the SSP button (D),
LED will be lit orange. When in Mute mode the ind
tor LED will flash ON-OFF at approximately 1 seco
intervals.
I
MON O/S TE RE O BUTTON
When in the ON position (button depressed), the
Mono function is enabled. This function sums all
selected input signals together, and directs them
both channels. As long as the button is depresse
left or a right mono signal will be sent to both cha
of the preamplifier. All other preamplifier functions
operate normally.
J
M U T E - O P E R ATE BU TT ON
When in the OPERATE state, this button will allow
normal function. When in the MUTE state, the mu
signal is prevented from reaching the Outputs (R)
(L). To indicate a muted condition, the indicator L
(H) will flash OFF-ON at approximately 1 second i
vals.
Please Note that Muting does not work wh
SSP Mode.
K
ON-OFF BUTT ON
When in the ON position (button depressed), line
age is received by the Integrated 2 circuitry from
AC source. Due to the warm up characteristics o
tubes, it will take 40 seconds for the tubes to pas
signal. It is suggested that the Volume be turned
for this first minute. After the power-up time-out
(approx. 40 sec.) set the desired volume level. W
in the OFF position (not depressed), the Integrate
is not receiving power and is not operational.
C O N T R O L F U N C T I O N S
NOTE: Unterminated (open) inputs may produce hum from the
system loudspeakers when selected.
* This input also functions as an “Amplifier Only” input.