Audio Design Associates ADA 6.1 Operation & installation manual - page 11
Page 9
Connection of the Power-On Trigger
The ADA 6.1 has a feature that permits it to be turned on or to bypass from an external source. This
trigger can permit you to remotely control the activation of the ADA 6.1. When incorporated with
systems that use some type of control system, a touch screen, buttons can be setup on the touch
screen that would activate this trigger on demand.
The ADA Cinema Reference with software version 1.84 or greater has a setting in setup that permits
AUX DC 2 to trigger the ADA 6.1 on when it is decoding a true 5.1 source signal. When decoding
anything other than a 5.1 signal, the Cinema Reference will set the ADA 6.1 into bypass. If the user
wishes to bypass the ADA 6.1 during playback of 5.1 material, one can still turn off the front panel
switch on the ADA 6.1. To activate the Cinema Reference’s 6.1 Trigger, enter the Cinema Reference’s
Pro Setup Mode (see Cinema Reference manual).
Once in Pro Setup, turn the MODE knob until AUX DC TRIG2 appears and then press the MODE
knob.
The top line of the display will read the source selected and the bottom line will read either AUX DC
TRIG2 ON, AUX DC TRIG2 OFF, or 6.1 ADAPTER. Turn the MODE knob until 6.1 ADAPTER
is selected. Do not select AUX DC TRIG2 ON, because it will hold the trigger on regardless
of 5.1 detection. For sources that do not play 5.1 material, you may also lock in AUX DC
TRIG2 OFF.
Turn the INPUT knob one click to display the next source. Turn the MODE knob to display either
6.1 ADAPTER or AUX DC TRIG2 OFF.
Turn the INPUT knob again and repeat the above step for each input on the system.
Turn the VOLUME knob to exit Pro Setup.
To connect the Cinema Reference to the ADA 6.1, use a two conductor low voltage wire (18-22 Gauge)
and connect pin 1(-) to pin 1(-) and pin 2(+) to pin 2(+).
1
1
2
2
3
4
3
5
6
4
7
8
5
1
2
6
REC
OSD
MAIN
REC
1
7
8
REC
2
3
4
L
R
LS
RS
SUB
C
L
R
L
R
L
R
L
R
OUT
AUDIO OUTPUTS
AUDIO INPUTS
VIDEO INPUTS
VIDEO OUT
S-VIDEO OUT
1
2
3
4
DIGITAL AUDIO INPUTS
S-VIDEO INPUTS
LOW VOLTAGE
AC INPUT
115V-60Hz/230V-50Hz
AC OUTPUT
10A Max Switched
ADA Bus™
1 2 3 4
DATA PORT
Serial Data
12VDC OUT
100mA Max Per
DC 1
1- 2+
DC 2
1- 2+
HDTV/RGB
COMPONENT
VIDEO
SWITCHER
Use With DVD
Players or
Digital Video
Tape Players
1
2
OUT
Y
Cr
Cb
LASER DISC PLAYER
Dolby Digital (AC-3)
RF Switcher & AC-3
RF Demodulator
1
2
Connections!
In order to play an AC-3 Laser
Disc, you must connect the Digital
AC-3 Output to a Digital Audio
Input (RCA Type Coax) below.
DC Input Mute Switch
OFF
ON
CAUTION: Disconnect Supply Cord Before Servicing.
ATTENTION: Debrancher Avant Le Depannage.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION!
RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR
MADE IN U.S.A.
WARNING! Risk Of Hazardous Energy!
Make Proper Connections.
AVERTISSEMENT! Energie Electrique Dangereuse!
Faire Des Connexions Propres Pour L'Hautparleur.
Voir La Notice De Fonctionnement.
Use Same
Value Fuse
115V-1AS.B.
230V-.5AS.B.
Voltage
Selector &
Safety Fuse
On This Side
115 V
115V
230V
15
Manufactured under license from Dolby Laboratories Licensing Corp.
"Dolby", "Dolby Digital", "Pro Logic", & the Double-D Symbol are the trademarks of Dolby Laboratories Licensing Corp.
Manufactured under license from DTS Technology, LLC. DTS Digital Surround is a trademark of DTS Technology LLC.
Manufactured under license from Lucasfilm Ltd. U.S. patent numbers 5,043,970; 5,189,703; and 5,222,059.
Foreign patents pending. Lucasfilm and THX are registered trademarks of Lucasfilm Ltd.,
Cinema Reference
1
2
3
OPTICAL INPUTS
In order to play an AC-3 Laser Disc,
you must connect the Digital AC-3
Output to a Digital Audio Input.
R
INPUTS
OUTPUTS
LT SURR
RT SURR
LT SURR
1(-) 2(+)
12VDC
TRIGGER
12VAC
MAIN
POWER
MANUAL
RT SURR
BACK LT
BACK RT
ADA 6.1 Surround Back Processor
Manufactured in the U.S.A.
TRIGGER
MANUAL
6
L