B&B Electronics EIS-EXTEND-C Quick Start Manual
EIS-EXTEND-C-5009qsg
International Headquarters: 815-433-5100
www.bb-elec.com
European Headquarters: +353 91 792444
www.bb-europe.com
1
Items Included
2
Hardware Installation
3
Front Panel & LED Chart
4
DIP Switch Settings
Quick Start Guide
EIS-EXTEND-C
Ethernet Coaxial Extender
Front Panel LED’s (Ethernet and Line Connections)
Port LEDs
Status
Description
Steady
Power on
(Pwr stands for POWER)
Pwr
Off Power
off
Steady
Valid Ethernet connection
established
(Lnk stands for LINK)
Flashing Transmitting or receiving
Ethernet data
(Act stands for ACTIVITY)
Lnk/Act
Off
No valid Ethernet connection
nor transmitting/receiving
Ethernet data
Steady
Ethernet connection in full
duplex mode
(Fdx stands for FULL-DUPLEX)
Flashing Collision
occurred
Ethernet
(RJ-45)
Fdx
Off
Ethernet connection in half-
duplex mode
Rmt
Steady
Operating in remote mode
Loc
Steady
Operating in local mode
Err Steady
Error
occurred
Line
(BNC)
Lnk
Steady
A valid connection established
between local & remote
Top LEDs (BNC Line Connections)
LEDs Status Speed Distance
Green
1~ 5Mbps
up to 2600M
1
Amber
6~10Mbps
up to 2400M
Green
11~16Mbps
up to 2000M
2
Amber
17~20Mbps
up to 1800M
Green
21~29Mbps
up to 1600M
3
Amber
30~43Mbps
up to 1400M
Green
44~54Mbps
up to 1200M
4
Amber
55~63Mbps
up to 1000M
Green
64~74Mbps
up to 600M
5
Amber
75~85Mbps
up to 200M
1.
Apply Rubber feet to bottom of media converter and
select a suitable mounting location. Can be wall
mounted using slots on the bottom of case.
2.
Do not locate in areas subject to high moisture or
potentially wet conditions. Locate where the
temperature range does not exceed -10 to 60° C.
Make sure unit receives adequate ventilation.
3.
This Ethernet Extender is a plug-and-play device.
Connect the supplied AC to DC power adaptor to the
receptacle on the rear panel of the Ethernet Extender,
and then attach the plug into a standard AC outlet.
o
Ethernet
Coaxial
Extender
o
AC to DC Power Adaptor
o
This Quick Start Guide
o
Rubber
Feet
o
BNC to F-Type Adaptor
The LED indicators give you instant feedback on status of
the Ethernet Extender. Both port speeds are auto sensed.
Ethernet Extender mode settings are made very simple by
means of a switch at the rear panel of the Ethernet
Extender. One device must be set to local (Loc) and the
other to remote (Rmt) before devices are connected.
It makes no difference which unit is designated local and
remote as long as they are not both set the same.
The EIS-EXTEND-C provides one channel for
Ethernet over existing coaxial cable.
4.
Set the DIP switch located on the rear of the Ethernet
Extender to Loc (Local) or Rmt (Remote). Ethernet
Extenders work in pairs and must have one unit set as
Loc, the other as Rmt.
5.
Connect the Ethernet cable to the RJ-45 port on the
front of Ethernet Extender.
6.
Connect the coaxial cable to the BNC port on the front
of the Ethernet Extender. Opposite end connects with
paired Ethernet Extender located elsewhere. Coax
cable must be terminated with male BNC or F
connectors. BNC to F-Type adaptor required for F
style connector (included).
Note: Distance and speed may vary. The above table
represents the maximum performance which can be
expected under ideal conditions.