B&B Electronics iMcV-DS3 Operation Manual

Other manuals for iMcV-DS3: Operation Manual
Manual is about: SNMP-manageable module

Summary of iMcV-DS3

  • Page 1

    Imcv-ds3/e3/sts repeater operation manual ii fcc radio frequency interference statement this equipment has been tested and found to comply with the limits for a class a computing device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful ...

  • Page 2

    Iii table of contents fcc radio frequency interference statement .................................................... Ii limited lifetime warranty .................................................................................. Ii about the imcv-ds3/e3/sts ............................................

  • Page 3

    2 managed modules to manage imcv-ds3/e3/sts modules, an snmp agent must be present; the imediachassis requires an snmp management module. For a managed environment, first manually configure all of the desired dip switch selectable features to match what will be configured through the snmp management...

  • Page 4

    4 function switch settings result [(d) = default] loopback (iview 2 configurable) s1-1: off loopback disabled (d) s1-1: on loopback enabled loopback type (iview 2 configurable) s1-2: off coax (d) s1-2: on fiber jitter attenuation (iview 2 configurable) s1-3: off jitter attenuator on receive side s1-...

  • Page 5

    6 transmit liu waveshape (line build-out) this switch selects the optimal transmit waveshape for the line build-out distance on the coax line. The transmit waveshape can be set for a distance of either 0 to 255 feet or over 255 feet. This feature corrects problems related to cabling (i.E. Cross-talk...

  • Page 6

    8 remote unit this option allows the user to enable remote unit on the module. The remote unit feature is designed to work only as the remote module of the local/remote pairin the required master/slave configuration. With remote unit enabled, the user can easily perform the following: • test the lin...

  • Page 7

    10 pseudorandom bit sequence.” configure the local device for loopback, conduct the test, then check the pbeo led to verify errors were not received (refer to the led section for more information). 11 led operation the imcv-ds3/e3/sts module features several diagnostic leds per port. The led functio...

  • Page 8

    12 troubleshooting general troubleshooting • during installation, first test the fiber and bnc connections with all troubleshooting features disabled; then enable these features, if desired, just before final installation. This will reduce the features’ interference with testing. • when working with...

  • Page 9

    14 b&b electronics technical support tel: (800) 346-3119 (in the u.S. And canada) monday-friday, 7:00am-7”00pm cst +353 91 792444 (europe) monday through friday 8:00am - 5:00pm gmt fax: (815) 433-5109 u.S. And canada +353 91-79244s5 europe e-mail: support@bb-elec.Com u.S. And canada techsupport@bb-e...

  • Page 10

    16 electrostatic discharge precautions electrostatic discharge (esd) can cause damage to any product, add-in modules or stand alone units, containing electronic components. Always observe the following precautions when installing or handling these kinds of products 1. Do not remove unit from its pro...

  • Page 11

    International headquarters b&b electronics 707 dayton road ottawa, il 61350 usa phone (815)433-5100 — general fax (815) 433-5105 email: support@bb-elec.Com website: www.Bb-elec.Com european headquarters b&b electronics westlink commercial park oranmore, co. Galway, ireland phone +353 91-792444 — fax...