B&D Controll-A-Door 4 Instructions Manual - page 2
START BY READING THESE IMPORTANT SAFETY RULES
These safety alert symbols mean CAUTION - a personal safety or property damage instruction. Read these
instructions carefully. This garage door operator is deisgned and tested to offer reasonable safe service
provided it is installed and operated in strict accordance with the following safety rules.
Failure to comply with the following instructions may result in serious personal injury or property damage.
Caution: If your garage has no service entrance door, an emergency access device must be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
Keep garage door balanced. Sticking or binding doors
must be repaired. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under extreme
tension can cause serious personal injury.
Do not attempt
any adjustment. Call for professional garage door
service.
Do not wear rings, watches or loose clothing while
installing or servicing a garage door operator.
To avoid serious personal injury from entanglement,
remove
all ropes connected to the garage door before
installing the door operator.
Installation and wiring must be in compliance with your local
building and electrical codes.
Connect the power cord
only to properly earthed mains.
Lightweight doors of fiberglass, aluminium or steel
must be substantially reinforced to avoid door
damage. (See page 4). The best solution is to check with
your garage door manufacturer for an operator installation
reinforcement kit.
The safety reverse system test is very important.
Your garage door
must reverse on contact with a 25mm (1’)
obstacle placed on the floor. Failure to properly adjust the
operator may result in serious personal injury fro a closing
garage door.
Repeat the test once a month and make
any needed adjustments.
This unit should not be installed in a damp or wet
space.
Do not use the force adjustments to compensate for
a binding or sticking garage door. Excessive force will
interfere with the proper operation of the Safety Reverse
System or damage the garage door.
Fasten the
caution label adjacent to the lighted door control
button as a reminder of safe operating procedures.
Disengage all existing garage door locks to avoid
damage to garage door.
Install the lighted door control button (or any additional push
buttons)
in a location where the garage door is visible,
but out of the reach of children. Do not allow children
to operate push button(s) or remote control(s).
Serious personal injury from a closing garage door may result
from misuse of the operator.
Caution: Activate operator only when the door is in
full view, free of obstructions and operator is
properly adjusted. No one should enter or leave the
garage while the door is in motion. Do not allow
children to play near the door.
Use manual release only to disengage the trolley and, is
possible only when the door is closed.
Do not use the red
handle to pull the door open or closed.
Disconnect electric power to the garage door
operator before making repairs or removing covers.
This product is provided with a cable of special design which,
if damaged, must be replaced by a cable of the same
type; such a cable may be obtained from your local B&D
distributor and must be fitted by a specialist.
Contents:
Safety Rules: Page 1
Door Types: Page 1 - Illustration 1
Tools Required: Illustration 2
Hardware Provided:
Page 1 - Illustration 3
Before you Begin: Page 2
Completed Installation:
Page 2 - Illustration 4
Assembly:
Page 2 - Ilustrations 5 - 10
Installation:
Pages 3-4 Illustrations 11-20
Programming the Code:
Page 4 - Illustration 21
Adjustment:
Pages 4-5 - Illustrations 22-24
Install the Protector System
(Optional): Page 5 - Illustration 25
Activation of your Operator: Page 5
Care of your Operator: Page 5
Problems: Page 6
Maintenance of your Operator: Page 7
Specifications: Page 7
Warranty: Page 7
Door Types
- 1
A. Sectional Door with Curved Track - See 20 A - Connect door arm.
B. One-Piece Door with Horizontal Track Only
Tools Required
- 2
See Illustration
Hardware Provided
- 3
Assembly Hardware:
Installation Hardware:
(1) Washered Screws (2)
(7) Lock Nuts
(12) Carriage Bolts (2)
(17) Rope
(23) Ring Fasteners
(2) Hex Screws (2)
(8) Flat Washers (2)
(13) Wood Screws (4)
(18) Handle
(24) Rail Grease
(3) Nuts (2)
(9) Hex Screws (2)
(14) Screws (2)
(19) Insulated Staples
(25) Tension Assembly
(4) Lock Washers (2)
(10) Trolley Threaded
(15) Cleavis Pins (2)
(20) Anchors (2)
(26) 8mm Anchors (4)
(5) Master Links (2)
Shaft (1)
(16) Hex Screws (5)
(21) Lock Washers (8)
(27) Sheet Metal
(6) Carriage Bolts (4)
(11) Clevis Pin (1)
(22) Nuts (9)
Screws (2)