B&D Panelift B&D Storm-Shield PFI Installation Instructions Manual - page 6
It is recommended that this door is installed by a professorial door installer using a professional and specialized tool kit.
1.4 TOOLS
AVAILABLE B&D STANDARD FASTENER PACKS
FASTENER
STANDARD FASTENER
PACK PART NO.
STANDARD FASTENER PACK DESCRIPTION
Screw, Coach 5/16-9TpIx50
FK0011
Kit, Screw, Coach 5/16-9TpIX50 100pk
FK0012
Kit, Screw, Coach 5/16-9TpIX50 500pk
Screw, Coach 5/16-9TpIx80
FK0013
Kit, Screw, Coach 5/16-9TpIx80 100pk
FK0014
Kit, Screw, Coach 5/16-9TpIx80 500pk
plug, Nylon 5/16x50
FK0015
Kit, plug, Nylon 5/16x50 100pk
FK0016
Kit, plug, Nylon 5/16x50 500pk
plug, Nylon 5/16x80
FK0017
Kit, plug, Nylon 5/16x80 100pk
FK0018
Kit, plug, Nylon 5/16x80 500pk
Screw Tek 14G-20TpIx25
Flange Hex Head zp
FK0019
Kit, Screw Tek 14-20x25 100pk
FK0020
Kit, Screw Tek 14-20x25 500pk
Screw Tek 14G-20TpIx35
Flange Hex Head zp
FK0021
Kit, Screw Tek 14-20x35 100pk
FK0022
Kit, Screw Tek 14-20x35 500pk
Screw Masonary M8x75
Flange Hex Head
FK0023
Kit, Screw Anka M8x75 Flange Hex Head 50pk
FK0024
Kit, Screw Anka M8x75 Flange Hex Head 100pk
Screw, Coach M10x90
FK0037
Kit, Screw Coach M10x90 100pk
plug Nylon 14x70 M10
FK0038
Kit, plug Nylon 14x70 M10 100pk
Screw Masonary M10x75
FK0028
Kit, Screw Masonary M10x75 100pk
bolt & Nut 1/4"1/2"UNC
FK0040
Kit, bolt & Nut 1/4x1/2 UNC 100pk
bolt & Nut 5/16"7/8"UNC
FK0041
Kit, bolt & Nut 5/16x7/8 UNC 100pk
6
panelift
®
pFT, panelift
®
Icon
™
pFI, b&D Storm-Shield
™
pFI and Insul-Shield
™
Installation Instructions
Revision 9 - March 2016
IMPORTANT INFORMATION ON FASTENERS
The installer must select and use fasteners appropriate to the material into which they are being fixed.
For B&D Storm-Shield
™
PFI doors ensure you are complying to the latest high wind compliant details.
To download the latest drawings visit the B&D website at
www.bnd.com.au
IMPORTANT NOTES:
1. For b&D Storm-Shield™ pFI doors ensure you are complying to the latest compliance details.
2. For installation to substrate materials not covered in the above chart, the installer should seek expert advice.
3. The above fasteners are specifically selected for b&D panelift pFT & pFI doors only.
4. Substitute fasteners are not recommend unless approved.
5. The above chart specifies the fasteners for new substrate materials only. Seek specialist advice regarding pre-existing substrate materials.
6. It is important that correct washer and plug is used and the correct pilot hole drilled where specified.