- DL manuals
- B&D
- Door Opening System
- Roll-A-Door R1D
- Installation Instructions Manual
B&D Roll-A-Door R1D Installation Instructions Manual
Summary of Roll-A-Door R1D
Page 1
Series 1 includes r1d, r1f, r1r, r1m, r1me windrated installation instructions part no. 52214. Revision 2 december 2013 disclaimer these instructions are intended for professional garage door installers note: all references are taken from inside looking out roll-a-door ®.
Page 2
Revision 2 december 2013 contents 1.0 before you start 3 1.1 safety checklist 3 1.2 fastener recommendations for fitting garage doors 4 1.3 requirements before installation 5 1.4 fixing requirements 6 1.5 tools checklist 6 1.6 parts checklist 6 2.0 installation 7 2.1 install first bracket 7 2.2 inst...
Page 3
Revision 2 december 2013 1.0 before you start your new b&d roll-a-door ® has been designed to provide security, attractive appearance and smooth, low effort operation. Your door will not provide optimum performance unless it is installed correctly. For satisfactory door operation please follow the i...
Page 4
Revision 2 december 2013 1.2 fastener recommendations for fitting garage doors important information on fasteners coach bolts/screws supplied with this product are not suitable. The installer must select and use fasteners appropriate to the material into which they are being fixed. Refer to drawings...
Page 5
Revision 2 december 2013 opening requirements the door is designed to be mounted behind the opening, therefore you will need to measure and check: opening width - as the door overlaps each side by 55mm or more, the door should be 110mm wider than the opening. A wider door can be fitted as long as ad...
Page 6
Revision 2 december 2013 the installer must select and use fasteners appropriate to the material into which they are being fixed. Refer to fastener recommendations on page 4 and drawings s01e, s02e, s03e. Note: it is the installer’s responsibility to ensure that the fixing methods are sound. 1.4 fix...
Page 7
Revision 2 december 2013 2.0 installation 2.1 install first bracket a) measure the door curtain width and mark where edge of the curtain will be, allowing for over lap on each side of the opening. B) add clearance of 35 to 75mm from edge of curtain to inside edge of bracket to determine positioning ...
Page 8
Revision 2 december 2013 2.3 place door on brackets a) check the axle length and cut if sideroom is limited. Before cutting, make sure the floating axle is free and centred. Centre will be found by rotating the axle a quarter turn in either direction then releasing . With centre found, make a clear ...
Page 9
Revision 2 december 2013 2.7 attaching stop to attach metal stops to bottom rail of door. A) hook stop behind lip in rail, as shown. B) secure from underneath the rail with screws supplied. You will need to trim the weatherseal flush with the end of the bottom rail. 1 2 wood chock roll-a-guide restr...
Page 10: Sampl
Revision 2 december 2013 2.8 s02h sampl e only contac t b&d d irect or v isit www.B nd.Com .Au for t he latest u pdates 10 series 1 windrated installation instructions.
Page 11: Sampl
Revision 2 december 2013 2.9 s03h sampl e only contac t b&d d irect or v isit www.B nd.Com .Au for t he latest u pdates 11 series 1 windrated installation instructions.
Page 12: Sampl
Revision 2 december 2013 2.10 s04h sampl e only contac t b&d d irect or v isit www.B nd.Com .Au for t he latest u pdates 12 series 1 windrated installation instructions.
Page 13
Revision 2 december 2013 2.12 fitting handle fit the handle to the outside of the door using the screws, nuts and washers provided. Nylofelt legs g o under nylofelt and snap over curtain edge legs (a) (b) hook this end first lock c orrugatio n (c) double sided adhesive tape lock bar c over lock body...
Page 14
Revision 2 december 2013 2.13 centre lift lock nylofelt legs g o under nylofelt and snap over curtain edge legs (a) (b) hook this end first lock c orrugatio n (c) double sided adhesive tape lock body lock arm cut- lock bar cover lock bar cover faceplate (c) (g) (f) (i) (d) lock bar a) raise the curt...
Page 15
Revision 2 december 2013 2.14 final adjustment 1. If the door is hard to operate in any direction check that the door is not jamming in the guides. Check: a) the guide clearances; b) that guides are plumb; c) that the guide surfaces are clean and free from oil; d) that locking bars are the correct l...
Page 16
Revision 2 december 2013 2.16 fixing alternatives 1. Alternative bracket fitting an “a2”extended leg bracket should be used in conjunction with the standard “a” style bracket. “a” bracket “a2” extended leg bracket secure w ith masonry anchors secure if possible coach bolts heavier coach screw s or 3...
Page 17
3.0 after installation care general care of your roll-a-door ® cleaning bluescope colorbond ® finish your b&d roll-a-door ® door has been pre-painted with a silicone modified polyester formulation, which is one of the best paint films commercially available today. However, all exposed surfaces requi...