Summary of Pearl BLQF
Page 1
1.
Page 2: Table of Contents
2 table of contents page 3. Parts & hardware list 6. Step 1- remove track supports 7. Step 2- table assembly 8. Step 3- end leg assembly 11. Step 4- middle leg assembly 13. Step 5- rotate the frame 14. Step 6- support rail assembly 15. Step 7- track assembly 18. Step 8- ratchet stop assembly 20. Ste...
Page 3
3 pole section, 5’ (8) pole coupler (4) baby lock pearl frame parts & hardware list left pole bracket assembly (1) support rail (2) table section with plastic top 5’ (2) m6 x 12mm socketed washer head cap screw[ track support screws (12) (comes in track supports on table sections) track support, 5’ ...
Page 4
4 bungee clamps (4) lower middle leg (1) upper middle leg (1) batting bar bracket assembly (w/clamp) (2) m6 x 25mm socketed washer head cap screw: batting bar bracket screws (8) m8x25mm socketed button head cap screw (for thick metal on support rail) (12) nut, m8 nylon lock (4) metal washer, m8 (5) ...
Page 5
5 5mm allen wrench (1) pole end assembly with short bolt (2) pole end assembly with long bolt (1) 4mm allen wrench (1) hand wheel assy qf09318-720 short bolt ratchet wheel qf09318-730 qf09318-730 long bolt ratchet wheel hand wheel assy qf09318-720 short bolt ratchet wheel qf09318-730 qf09318-730 lon...
Page 6: Step 1
6 step 1: remove track supports parts needed 2-table section tools required 4mm allen wrench (provided) note: the track support finish could be damaged if not protected or if placed onto a rough surface. Handle with care. 1-1: place the table sections with the track supports face down onto a protect...
Page 7: Step 2
7 step 2: table assembly parts needed 2-table section 2-table splice 12- m8x16mm socketed button head cap screw qf09318-07 tools required 5mm allen wrench (provided) 2-1: with the table sections face down (large round screw holes for track supports up), slide the two table sections together end to e...
Page 8: Step 3
8 step 3: end leg assembly parts needed 1-table assembly 2-upper end leg a 2-upper endleg b 2-lower end leg 4-leveling glide 12-m8x16mm socketed button head cap screw qf09318-07 8-m8x25mm socketed button head cap screw qf09318-06 4-nylon washer tools required 5mm allen wrench (provided) 3-1: with th...
Page 9: Step 3
9 fig. 3-3 detail 3-3 step 3 end leg assembly (continued) 3-3: slide one (1) lower corner leg onto the two (2) upper corner legs on each end of the frame as shown in fig. 3-2 on the previous page and fig. 3-3. Choose the preferred height of the frame based on the table in fig. 3-4. Place an m8x16mm ...
Page 10: Step 3
10 fig. 3-5 step 3 corner leg assembly (continued) detail 3-4 3-4: thread a leveling glide into each end of the corner leg assemblies, leaving about 1/2” of the threads exposed to make it easier to level the frame later. (fig. 3-5 and detail 3-5) detail 3-5.
Page 11: Step 4
11 step 4 middle leg assembly step 4: middle leg assembly parts needed 1-table assembly 1-upper middle leg 1-lower middle leg 5-m8x16mm socketed button head cap screw qf09318-07 1-m8 nylon washer qf05300-157 2-leveling glide tools required 5mm allen wrench 4-1: place the upper middle leg on the cent...
Page 12: Step 4
12 step 4 middle leg assembly (continued) 4-2: slide the lower middle leg onto the upper middle leg, and insert an m8x16mm qf09318- 07 with nylon washer qf05300-157 into the same height setting as the corner legs. Fully tighten the m8x16mm qf09318-07 with the 5mm allen wrench. (fig. 4-2) 4-2: thread...
Page 13: Step 5
13 step 5: uprighting the frame parts needed 1-frame assembly tools required helper note: the end screws have been temporarily installed and lightly tightened into the end of the frame to support the legs while uprighting it. Care should be taken with the legs until they are fully tightened. (fig. 5...
Page 14: Step 6
14 step 6: support rail assembly parts needed 1-frame assembly 2-support rail 8-m8x25mm socketed button head cap screw qf09318-06 (already in frame ends) tools required 5mm allen wrench (provided) 6-1: remove the four (4) lightly-tightened m8x25mm qf09318-06 end screws from the frame, as shown in fi...
Page 15: Fig. 5-1
15 fig. 5-1 qf09318-02 fig. 5-2 qf09318-02 fig. 5-3 qf09318-02 fig. 5-4 qf09318-02 fig. 5-1 qf09318-02 fig. 5-2 qf09318-02 fig. 5-3 qf09318-02 fig. 5-4 qf09318-02 step 7 track assembly 7-3: to prepare for joining the sections together, screw one m5x8mm qf09318-304 into the third hole from the splice...
Page 16: Step 7
16 fig. 7-3 plastic track track support insert the other end of the coupler into second prepared track support section. Hold the two adjoining track support sections tightly together and thread an m5x8mm qf09318-304 into the first hole of the second track support and lightly tighten. You may need to...
Page 17: Step 7
17 step 7 track assembly (continued) fig. 7-5 fig. 7-6 track support plastic track 7-9: place the machine onto the carriage and again, roll it the entire length of the frame, working the tracks into the wheels as you go. Lightly tighten the front track support screws as you move down the table. Chec...
Page 18: Step 8
18 step 8 ratchet stop assembly 8-4: following the parts order shown in fig. 8-1, thread one m6 x 48mm qf09318-204 through a ratchet-stop, ratchet-stop bushing, pole bracket (with ratchet-stop holder inserted) and finally into the ratchet-stop mount. Pay close attention to the orientation of the rat...
Page 19: Step 8
19 detail 8-1a detail 8-1b detail 8-1c step 8 ratchet stop assembly (continued) finger.
Page 20: Step 9
20 step 9: pole bracket assembly parts needed 1-frame assembly 1-pole bracket assembly with latches (right) 1-pole bracket assembly without latches (left) 4-m8x25 socketed button head cap screw qf09318-06 4-m8 flat washer qf09318-09 4-m8 lock nut qf09318-08 tools required 5mm allen wrench (provided)...
Page 21: Step 10
21 step 10 pole coupler assembly fig. 10-1 fig. 9-1 fig. 9-2 fig. 8-1 fig. 9-4 fig. 9-3 pole coupler pole section step 10: pole coupler assembly parts needed 8-pole sections 4-pole couplers 10-1: join two pole sections together by inserting a pole coupler into the end of one pole section (as shown i...
Page 22: Fig. 9-1
22 fig. 9-1 fig. 9-2 fig. 8-1 fig. 9-4 fig. 9-3 step 11: pole end assembly parts needed 4-pole assembly 5-pole end 2-short-bolt ratchet wheel assembly 1-long-bolt ratchet wheel assembly 1-hand wheel assembly 1-hand wheel insert tools required 17/13mm wrench (provided) 11-1: check one pole end to ens...
Page 23: Step 11
23 11-7: repeat steps 11-5 and 11-6 to add a second pole end to the other open end of the pole assembly just built and one pole end to each of the remaining 3 pole assemblies (fig. 11-5). Set the pole with two pole ends aside as the batting storage pole. Short-bolt ratchet-wheel assembly 11-8: check...
Page 24: Step 11
24 fig. 11-9 take-up pole 11-13: repeat step 11-10 to prepare the long-bolt ratchet wheel assembly for insertion. Ratchet wheel and hand wheel insertion 11-14: insert one short-bolt ratchet wheel assembly into the open end of a pole assembly as shown in fig. 11-8. Check that the pole end is inserted...
Page 25: Step 12
25 step 12: pole end assembly parts needed 2-batting bar bracket assembly 2-batting bar bracket clamp 8- m6x25mm socketed washer head cap screw qf05300-113 tools required m4 allen wrench (provided) 12-1: note: this step includes a recommendation for the position of the batting bar bracket. This posi...
Page 26: Steps 13 & 14
26 step 13: pole to frame assembly parts needed 1-frame assembly 1-batting storage pole 1-quilt-top pole 1-backing pole 1-take-up pole 13-1: place the poles on the frame as shown in fig. 13-1. The poles will snap past the plastic fingers, which are shown in detail 8-2a. Step 14: rubber end cap assem...
Page 27: Steps 15 & 16
27 step 15: bungee clamp assembly parts needed 1- frame assembly 4- bungee clamps qf09318-110 15-1: thread the bungee clamp cord from the inside of the frame through the bungee slot and then pull the cord in a downward movement to lock the bungee clamp into place. (fig. 15-1) 15-2: follow step 14-1 ...
Page 28: Steps 17 & 18
28 step 17: attach leaders parts needed 1-frame assembly with hook & loop tape applied to poles 3- leaders (sold separately blql) 17-1: mark the center of the leaders on both the hook & loop tape and the hemmed edge. Mark the center of the quilt top pole, backing pole and take-up pole with a permane...